Toshiba e-STUDIO206 Place paper in the drawer, Adjust the side guides to the desired paper size

Page 37

6 Place paper in the drawer.

yThe maximum number of sheets can be placed in one go is 250 (80 g/m2). Be sure that the stack height of paper is not higher than the line indicated at the inner side of the guide.

P.31 “Acceptable media types”

yFan the paper well before placing it in the drawer, otherwise multiple feeding could occur.

yPlace the paper face up. You may tell its “face” by the note on its wrapping paper.

7 Adjust the side guides to the desired paper size.

Be sure that a gap of approx. 0.5 mm (less than 1.0 mm in total) is left between the paper and each side guide (shown as “A” in the picture). If the gap is inappropriate, this could cause a paper misfeed.

A

Preparation 2 - Placing Copy Paper 35

Image 37

Contents Operators Manual for Copying Functions Page Preface PrefaceWorking environment For Germany onlyPage Lineup of our manuals Before Reading This ManualDescription of original/paper direction How to read this manual Signal in this manualTrademarks Contents 100 Copying in Same Page Order as Originals Sort Copying111 Cleaning charger 101 Cleaning transfer charger 102Contents Recommended toner cartridges Toshiba Quality Is Second to NoneCartridge detecting function Toner remaining check functionToner Supplies / PartsGeneral Functions extended by various options Features of e-STUDIO166/206Ecological energy-saving design When installing or moving General Precautions10 cm 80 cm Other pointsWhen using the equipment Position of Certification label, etc When handling supplies During maintenance or inspectionPoration Disclaimer NoticeEnergy Star programme Environmental InformationDescription of Each Component Preparation 1 Turning Power onPreparation 2 Placing Copy Paper Front / Right side Description of Each ComponentPlaten Cover Automatic Document Feeder optional, MR-2017Left side / Inner side Receiving tray Scanning area USB terminal 4-pinOriginal scale Platen sheetConfiguration of options Control panel Density adjustment buttons/lamps Original mode button/lampsLED display Copy qty. / zoom display selecting button/lampDrawer button/lamps Original setting lampCopy button/lamps Original button/lampsTurning power on Preparation 1 Turning Power onTurning power OFF To turn the equipment into the energy saving mode manually Saving energy when not in use Energy saving modeCancelling the energy saving mode Acceptable media types Preparation 2 Placing Copy PaperFeeder Media type Paper size Maximum sheet Capacity *1 Paper types not acceptable Recommended paperStoring paper Media type Product namePress down the paper plate Placing paper in drawersWiden the gap with both hands Place paper in the drawer Adjust the side guides to the desired paper sizeRegister the paper size into the equipment Do not let your fingers be caught when closing the drawerRegistering standard size A3, A4, A4-R, A5-R, B4 Preparation 3 Registering Size of Paper PlacedCode No Registering other standard sizesPreparation 3 Registering Size of Paper Placed Press the Start button Placing Originals Using Bypass TrayMaking Copies Setting position Type of origi When the built-in memory has become full during scanningPlacing Originals Acceptable originalsPlacing originals on the original glass Placing booklet-type originals such as books or catalogues Precautions for Automatic Document Feeder optional Using Automatic Document Feeder optionalWhen black streaks appear on the copied image Media types Maximum size Maximum number Paper weightPlacing originals on Automatic Document Feeder optional When placing a large amount of originals with a long widthCheck if paper is placed in the drawer Making CopiesPlace the original Select the copy modes as requiredWhen the paper has run out When the number of sheets exiting has exceededStopping/Resuming copying Press the CLEAR/STOP button during scanning or copyingPress the Interrupt button Interrupting copying and making another copy Interrupt copyMedia type Paper size Maximum sheet Capacity *1 Using Bypass TrayPreparation Registering paper size placed on bypass tray ST-R Folio Comp Using Bypass Tray Press the Start button Bypass copying on standard size paper Placed on the bypass tray is lit Using Bypass Tray Page Zooming In/Out Copy Image Default Settings Paper SelectionAutomatic paper selection APS Manual paper selection Contents Default setting at installation Default SettingsAutomatic paper selection APS Paper SelectionPlace the original on the Automatic Document Feeder Automatic paper selection APSPlace paper in the drawer Place the original Manual paper selectionSelecting the drawer of the equipment Automatic magnification selection AMS Zooming In/Out Copy ImageAutomatic magnification selection AMS Specifying reproduction ratio manuallyIf the Function Clear lamp is blinking and copying stops Specifying both the sizes of the original and the copy paper Press Zooming out or Specifying reproduction ratio manuallyDesired reproduction ratio appears Zooming in button untilZooming In/Out Copy Image Copying in Same Page Order as Originals Sort Copying Selecting Image Mode To adjust the density to the desired level Adjusting Density LevelTo return it to the automatic copy density mode DarkPage Settings and Management of Equipment All lamps on Sound on All lamps off Sound off Switching Operation Sound On/OffChecking Total Number Copied Switch the display to check the rest of the total numberPress Button for more than two seconds Page When Message Lamp is Lit/Blinking Paper Jams TroubleshootingCover open lamp When Message Lamp is Lit/BlinkingPaper empty lamp Toner lampRecommended toner cartridges Paper jam lamp Service call lampPaper Jams When paper jams occur frequentlyChecking position of paper jams Paper jams within Automatic Document Feeder optional When releasing jammed paperRaise the lever, and then open the upper cover Do not tear jammed paperPaper Jams Pull out the paper jammed on the bypass tray Paper jams on bypass trayPaper jam behind transfer unit Close the transfer unit and the side cover Paper jams within fuser unitPaper Jams Paper jams within Paper Feed Unit optional Open the front cover Replacing Toner CartridgeHold down the green lever Pull out the toner cartridge Clean the charger Replacing Toner Cartridge With the transfer charger wire General operation Before Calling Service TechnicianPhenomenon Usual cause Countermeasure Original/Copy paper-related items Toner-related itemsImage trouble Tion Charger is dirty Clean the charger Page Daily Inspection 100 Maintenance and InspectionOriginal glass Guides Platen sheet Daily InspectionOpen the front cover Clean the charger Cleaning chargerCleaning transfer charger Daily Inspection Page Specifications and Options OPC STUDIO166/206 SpecificationsPaper size Feeder STUDIO166 STUDIO206 Continuous copying speedAutomatic Document Feeder Specifications of OptionsPaper Feed Unit Packing List Page Index 106 DP-1660/2060 OME06015700 Multifunctional Digital Systems