Toshiba e-STUDIO166 manual When Message Lamp is Lit/Blinking, Cover open lamp, Paper empty lamp

Page 80

5 TROUBLESHOOTING

When Message Lamp is Lit/Blinking

Message lamps on the control panel are lit or blink depending on the status of the equipment. Each lamp shows the following status:

1

2

3

4

5

1.Cover open lamp

This blinks when any cover of the equipment, such as the front cover, the side cover or the upper cover of the Automatic Document Feeder (optional), is not securely closed. Close it securely.

2.Paper empty lamp

This blinks when the paper in a drawer or on the bypass tray has run out. Add paper. For how to place paper, see the following pages for the details:

P.33 “Placing paper in drawers”

P.50 “Using Bypass Tray”

3.Toner lamp

This shows you the current status of the toner cartridge by means of the cartridge detecting function and the toner remaining check function (only when a TOSHIBA-recommended toner cartridge is used) as follows:

Lit: There is now little toner left in the toner cartridge, or the toner cartridge is not installed correctly.

Blinking: The toner in the toner cartridge has run out.

yWhen the toner lamp is lit, there is still a little toner remaining in the toner cartridge. Do not replace the toner cartridge until the toner lamp starts blinking.

yIt occasionally happens that the toner lamp may not light because the toner remaining in the cartridge does not lie evenly.

yWhen the toner lamp is lit, it is advisable to purchase a new TOSHIBA-recommended cartridge to prepare for its replacement.

yWhen the toner lamp is blinking and the toner in the toner cartridge has run out, replace the toner cartridge with a new one.

P.89 “Replacing Toner Cartridge”

78 When Message Lamp is Lit/Blinking

Image 80

Contents Operators Manual for Copying Functions Page Preface PrefaceFor Germany only Working environmentPage Before Reading This Manual Lineup of our manualsHow to read this manual Signal in this manual Description of original/paper directionTrademarks Contents Copying in Same Page Order as Originals Sort Copying 100Cleaning charger 101 Cleaning transfer charger 102 111Contents Toshiba Quality Is Second to None Recommended toner cartridgesCartridge detecting function Toner remaining check functionGeneral Supplies / PartsToner Ecological energy-saving design Features of e-STUDIO166/206Functions extended by various options General Precautions When installing or movingOther points 10 cm 80 cmWhen using the equipment Position of Certification label, etc During maintenance or inspection When handling suppliesDisclaimer Notice PorationEnvironmental Information Energy Star programmePreparation 2 Placing Copy Paper Preparation 1 Turning Power onDescription of Each Component Description of Each Component Front / Right sidePlaten Cover Automatic Document Feeder optional, MR-2017Left side / Inner side USB terminal 4-pin Receiving tray Scanning areaOriginal scale Platen sheetConfiguration of options Control panel Original mode button/lamps Density adjustment buttons/lampsLED display Copy qty. / zoom display selecting button/lampOriginal setting lamp Drawer button/lampsCopy button/lamps Original button/lampsTurning power OFF Preparation 1 Turning Power onTurning power on Cancelling the energy saving mode Saving energy when not in use Energy saving modeTo turn the equipment into the energy saving mode manually Feeder Media type Paper size Maximum sheet Capacity *1 Preparation 2 Placing Copy PaperAcceptable media types Recommended paper Paper types not acceptableStoring paper Media type Product namePlacing paper in drawers Press down the paper plateWiden the gap with both hands Adjust the side guides to the desired paper size Place paper in the drawerDo not let your fingers be caught when closing the drawer Register the paper size into the equipmentPreparation 3 Registering Size of Paper Placed Registering standard size A3, A4, A4-R, A5-R, B4Registering other standard sizes Code NoPreparation 3 Registering Size of Paper Placed Press the Start button Making Copies Using Bypass TrayPlacing Originals When the built-in memory has become full during scanning Setting position Type of origiPlacing Originals Acceptable originalsPlacing originals on the original glass Placing booklet-type originals such as books or catalogues Using Automatic Document Feeder optional Precautions for Automatic Document Feeder optionalWhen black streaks appear on the copied image Media types Maximum size Maximum number Paper weightWhen placing a large amount of originals with a long width Placing originals on Automatic Document Feeder optionalMaking Copies Check if paper is placed in the drawerPlace the original Select the copy modes as requiredWhen the number of sheets exiting has exceeded When the paper has run outStopping/Resuming copying Press the CLEAR/STOP button during scanning or copyingInterrupting copying and making another copy Interrupt copy Press the Interrupt buttonUsing Bypass Tray Media type Paper size Maximum sheet Capacity *1Preparation Registering paper size placed on bypass tray ST-R Folio Comp Using Bypass Tray Press the Start button Bypass copying on standard size paper Placed on the bypass tray is lit Using Bypass Tray Page Automatic paper selection APS Manual paper selection Default Settings Paper SelectionZooming In/Out Copy Image Default Settings Contents Default setting at installationPaper Selection Automatic paper selection APSPlace the original on the Automatic Document Feeder Automatic paper selection APSManual paper selection Place paper in the drawer Place the originalSelecting the drawer of the equipment Zooming In/Out Copy Image Automatic magnification selection AMSAutomatic magnification selection AMS Specifying reproduction ratio manuallyIf the Function Clear lamp is blinking and copying stops Specifying both the sizes of the original and the copy paper Specifying reproduction ratio manually Press Zooming out orDesired reproduction ratio appears Zooming in button untilZooming In/Out Copy Image Copying in Same Page Order as Originals Sort Copying Selecting Image Mode Adjusting Density Level To adjust the density to the desired levelTo return it to the automatic copy density mode DarkPage Settings and Management of Equipment Switching Operation Sound On/Off All lamps on Sound on All lamps off Sound offPress Button for more than two seconds Switch the display to check the rest of the total numberChecking Total Number Copied Page Troubleshooting When Message Lamp is Lit/Blinking Paper JamsWhen Message Lamp is Lit/Blinking Cover open lampPaper empty lamp Toner lampRecommended toner cartridges Service call lamp Paper jam lampChecking position of paper jams When paper jams occur frequentlyPaper Jams When releasing jammed paper Paper jams within Automatic Document Feeder optionalRaise the lever, and then open the upper cover Do not tear jammed paperPaper Jams Paper jams on bypass tray Pull out the paper jammed on the bypass trayPaper jam behind transfer unit Paper jams within fuser unit Close the transfer unit and the side coverPaper Jams Paper jams within Paper Feed Unit optional Hold down the green lever Replacing Toner CartridgeOpen the front cover Pull out the toner cartridge Clean the charger Replacing Toner Cartridge With the transfer charger wire Phenomenon Usual cause Countermeasure Before Calling Service TechnicianGeneral operation Toner-related items Original/Copy paper-related itemsImage trouble Tion Charger is dirty Clean the charger Page Maintenance and Inspection Daily Inspection 100Daily Inspection Original glass Guides Platen sheetCleaning charger Open the front cover Clean the chargerCleaning transfer charger Daily Inspection Page Specifications and Options STUDIO166/206 Specifications OPCContinuous copying speed Paper size Feeder STUDIO166 STUDIO206Paper Feed Unit Specifications of OptionsAutomatic Document Feeder Packing List Page Index 106 DP-1660/2060 OME06015700 Multifunctional Digital Systems