Toshiba TDP-S9 owner manual Specifications, List of supported signals Hdtv signals

Page 41

Specifications (Continued)

■List of supported signals (HDTV signals)

Signal format	fh(kHz)	fv(kHz)
480i	15.8 kHz	60 Hz
480p	31.5 kHz	60 Hz
576i	15.6 kHz	50 Hz
576p	31.3 kHz	50 Hz
720p	45.0 kHz	60 Hz
720p	37.5 kHz	50 Hz
1080i	33.8 kHz	60 Hz
1080i	28.1 kHz	50 Hz

■List of supported signals (Video, S-Video signals)

Video mode	fh(kHz)	fv(Hz)	fsc(MHz)
NTSC	15.73	60	3.58

PAL	15.63	50	4.43

SECAM	15.63	50	4.286
PAL-M	15.73	60	3.58
PAL-N	15.63	50	3.58
PAL-60	15.73	60	4.43
NTSC4.43	15.73	60	4.43

■Pin assignment of COMPUTER IN terminals

5 1

106

15 11

Mini D sub 15 Pin connector

Input Signal

• RGB input

RGB signals:	0.7V (p-p) 75 Ω
Horizontal sync signal:	TTL level (Pos/neg polarity)
Vertical sync signal:	TTL level (Pos/neg polarity)
• Y/PB/PR input
Y signal:	1.0V (p-p) 75 Ω
PB/PR signals:	0.7V (p-p) 75 Ω

	Pin	Pin description
	No.	During RGB input	During Y/PB/PR input
	1	Video signal (R)	Color difference signal (PR)
	2	Video signal (G)	Luminance signal (Y)
	3	Video signal (B)	Color difference signal (PB)
	4	N.C	∗
	5	GND	∗
	6	GND (R)	GND (PR)
	7	GND (G)	GND (Y)
	8	GND (B)	GND (PB)
	9	+5V	∗
	10	GND	∗
	11	GND	∗	Others
	12	SDA	DDC data serial signal	Others
	12	SDA	DDC data serial signal
	13	Horizontal sync signal	∗
	14	Vertical sync signal	∗
	15	SCL	DDC data clock signal

∗Do not connect anything.

41

Image 41

Contents TDP-S9 Svga USA only Safety PrecautionsBefore Using Source of Light Important Safety InstructionsHeat Lightning storms Important Safety InstructionsAccessories Replacement Parts Important Precautions Power Supply Cord SelectionPlace and Manner of Installation Save Original Packing MaterialsExemption Clauses Important Precautions Avoid Volatile LiquidOther Cautions and Informations Remote Control BatteryContents Others MaintenanceChecking the package contents Preparations Names of each part on the main unitNames of each part on the control panel and remote control Parts on the rear panel Operating the remote Control Preparing and using the remote controlLoading a Lithium battery into the remote control Projection Distance and Size PlacementPlacement Styles Before connection ConnectionConnecting the power cord Turning the power on and offTurning the power on Removing the lens coverPress the I/ ON/STANDBY button again Turning the power offBasic operations Turn on the powerSelect the language Activate the connected deviceTo adjust the horizontal angle, use the tilt adjuster Projector placement angle adjustmentsAdjusting the screen size and focus Correcting the keystone distortion Keystone Using handy featuresManually selects an input source Source Switching the image aspect ratio 43/169 Automatically adjusts frequency and phase AutoPress the remote controls Mute button Cutting off the sound temporarily MuteHow to use the menus Using the menusImage menu Using the menuSaturation Video menuTint SharpnessDisplay menu PhaseTracking PositionLanguage Language menuAdvanced menu Using the menuMute VolumeAudio menu Immediately replace the lamp when Lamp LED lights amber Lamp replacementWhen the lamp is broken About lampLamp Hours Reset Unplug power cord Wait until lamp is sufficiently cooledRemove the lamp cover Pull out the lampLamp replacement Lens and main unit cleaningLens cleaning Main unit cleaningBrightness Status displayBefore calling service personnel Specification SpecificationsList of general specifications List of supported signals RGB signals List of supported signals Hdtv signals SpecificationsList of supported signals Video, S-Video signals Pin assignment of Computer in terminalsSeparately Sold Product Pin assignment of S-Video terminal