4. DIP SWITCH FUNCTIONS
4. DIP SWITCH FUNCTIONS
4. DIP SWITCH FUNCTIONS
The DIP switches are located to the right of the supply shaft.
WARNING:
Turn the POWER OFF before switching the functions.
(1)DIP SW 2
Supply Shaft
Ribbon Shaft
No. | ON/OFF | Function |
| ||
| 1 |
| 2 |
| Transmission speed |
1 | OFF |
| OFF | 2400 BPS |
|
| ON |
| OFF | 4800 BPS |
|
2 | OFF |
| ON | 9600 BPS |
|
| ON |
| ON | 19200 BPS |
|
3 |
| OFF | 1 bit | Stop bit length | |
| ON | 2 bit |
| ||
|
|
| |||
4 |
| OFF | 7 bit | Data length | |
|
| ON | 8 bit |
| |
5 |
| OFF | without | Parity check | |
| ON | with |
| ||
|
|
| |||
6 |
| OFF | EVEN | Parity check (effective when DIP | |
| ON | ODD | SW #5 is set to ON.) | ||
|
| ||||
| 7 |
| 8 |
|
|
|
|
|
|
|
|
| OFF |
| OFF | XON/XOFF (No XON is output at the power on time.) | Data protocol |
|
|
|
| (XOFF is output at the power off time.) |
|
7 | ON |
| OFF | READY/BUSY (DTR) |
|
|
|
| (No XON is output at the power on time.) |
| |
|
|
|
|
| |
|
|
|
| (No XOFF is output at the power off time.) |
|
|
|
|
| READY/BUSY (RTS) |
|
|
|
|
| (No XON is output at the power on time) |
|
|
|
|
| (No XOFF is output at the power off time.) |
|
8 | OFF |
| ON | XON/XOFF + READY/BUSY |
|
|
|
| (XON is output at the power on time.) |
| |
|
|
|
|
| |
|
|
|
| (XOFF is output at the power off time.) |
|
| ON |
| ON | XON/XOFF (XON is output at the power on time.) |
|
|
|
|
| (XOFF is output at the power off time.) |
|
Fig.
(2)DIP SW 1
No. |
| ON/OFF |
|
| Function | |
1 |
|
| OFF |
| Without | Auto ribbon save function |
|
| ON |
| With |
| |
|
|
|
|
| ||
|
| 2 | 3 | 4 |
|
|
2 |
| OFF | OFF | OFF | English | Language to display LCD error |
| ON | OFF | OFF | German | message | |
|
| |||||
3 |
| OFF | ON | OFF | French |
|
| ON | ON | OFF | Dutch |
| |
|
|
| ||||
4 |
| OFF | OFF | ON | Spanish |
|
| ON | OFF | ON | Japanese |
| |
|
|
| ||||
|
| OFF | ON | ON | Italian |
|
|
| ON | ON | ON | Not used |
|
5 |
|
| OFF |
| Without | Auto media feed after a cut issue |
|
| ON |
| With | (See page | |
|
|
|
| |||
6 |
|
| OFF |
| Without | Use of the |
|
| ON |
| With | function in cut mode Refer to Note 2. | |
|
|
|
| |||
7 |
|
| OFF |
| Must be set to OFF. |
|
|
| ON |
|
|
| |
|
|
|
|
|
| |
8 |
|
| OFF |
| Must be set to OFF. |
|
|
| ON |
|
|
| |
|
|
|
|
|
| |
|
|
|
|
|
|
|
NOTES: 1. The shaded settings are the factory default settings. "OFF" means "OPEN".
2.The DIP switch
3.If you would like to switch to READY/BUSY (DTR) or to READY/BUSY (RTS) of data protocol, please contact your authorized TOSHIBA TEC representative.