Toshiba B-SA4TM-TS12-QM-R Rfid Tag, Example 1 UPM Raflatac’s Rafsec Short Dipole 2 Tag

Page 107

7. SUPPLY SPECIFICATIONS

ENGLISH VERSION EO1-33047

7.1 Media

7.1.5 RFID Tag

The B-SA704-RFID-U2-EU-R supports EPC C1 Gen2 tags.

Cautions for using RFID Tags

(1) Location of RFID Tag

The location of an RFID tag in a label influences on the accuracy of writing data on the RFID tag. It is impossible to define the one best location for every RFID tag in labels because the best location depends on the type of RFID tag and RFID tag antenna.

The RFID Analyze Tool can evaluate the accuracy of writing data on the RFID tag.

For the RFID Analyze Tool, please contact the dealer or your nearest TOSHIBA TEC representative.

As a guideline, the best location for some common RFID tags is given below.

It is recommended to use the RFID Analyze Tool to evaluate the accuracy of writing data on an RFID tag to be used, then determine a specific location of the RFID tag.

If the RFID tag cannot be placed on the best location specified, contact the dealer or nearest TOSHIBA TEC representative.

Note that the best location described in this specification may not be applicable depending on the type or paper or glue even if the same RFID tags are used. This guideline applies to RFID labels for thermal transfer issue. When using the media made of PET or thermal paper, the best location needs to be found again.

Example 1) UPM Raflatac’s Rafsec Short Dipole 2 Tag

It is recommended to locate the vertical center of an RFID tag at 27 mm ± 3 mm from a leading edge of a label and align the horizontal center with the horizontal center of the label.

27mm±3mm

Media feed direction

E7- 4

Image 107
Contents SA4TM Series Vorsicht CE Compliance for EU onlySA4TM Series Waste Recycling information for users For Safety Precautions for Handling of Wireless Communication DeviceMeanings of Each Symbol Safety SummaryRequest Regarding Maintenance PrecautionsTable of Contents EA4-1 EA1-1EA2-1 EA3-1Product Overview Introduction FeaturesAccessories Rear View DimensionsAppearance Front ViewInterior Operation PanelOption Name Type Usage OptionsReference Printer SetupSetup Flow ProcedureExample of US Type InstallationConnecting the Power Cord Attaching the Printer Rear SupportInsert the Media Shaft into the core of a media roll Loading the MediaTake out the Media Holder Ass’y from the printer Raise the Release Lever and remove the Media Holder LeftPlace the Media Holder Ass’y into the printer Fold the Release Lever to lock the Media Holder LeftClick Upper Sensor Upper SensorLever Ass’y Setting the Feed Gap Sensor position Setting the Black Mark Sensor position Strip mode Option Batch modePress down the Release Bar to open the Strip Unit Tag paper or Thick paper Cut mode OptionLabel or Thin media Loading the Ribbon Open the Ribbon Cover Gently close the Top Cover until it clicks ContConnecting the Printer to Your Host Computer Turning the Printer How to enter the System Mode Sequentially Parameter SettingWhile 2PARAMETER SET is displayed on the LCD Message Time the Pause key is pressed, the sub menus are displayedAfter selecting a character code, press the Pause key Character Zero SelectionCharacter Code Selection Use the Feed or Restart key to select a desired optionAfter selecting a data length, press the Pause key Baud Rate SelectionAfter selecting a baud rate, press the Pause key Data Length SelectionFlow Control Code Selection Stop Bit Length SelectionParity Selection After selecting an auto forward wait, press the Pause key LCD Language SelectionAfter selecting a language, press the Pause key Auto Forward Wait SelectionControl Code Selection After selecting the Feed key function, press the Pause key Strip Wait Status SelectionAfter selecting the Strip Wait Status, press the Pause key Feed Key Function SelectionAfter selecting a Euro code, press the Pause key Kanji Code SelectionAfter selecting a Kanji code, press the Pause key Euro Code SelectionAfter selecting an ACK/BUSY timing, press the Pause key Auto Print Head Check SelectionAfter selecting auto print head check, press the Pause key Centronics Interface ACK/BUSY Timing SelectionAfter selecting the Input Prime, press the Pause key Web Printer Function SelectionInput Prime Selection Expansion I/O Interface Type Selection Ribbon Near End SelectionAfter selecting a Plug & Play, press the Pause key Label End/Ribbon Error SelectionPlug & Play Selection Pre-Strip Selection After selecting the Back Feed Speed, press the Pause key Maxi Code Specification SelectionReverse Feed Speed Selection After selecting a strip motor torque, press the Pause key Keyboard Interface SelectionAfter selecting a keyboard interface, press the Pause key Strip Motor Torque SelectionAfter selecting a printing method, press the Pause key Dump Mode SettingAfter selecting the receive buffer, press the Pause key Use the Feed or Restart key to select a printing methodRequired Label Length Data in the receive buffer is printed as followsReceive Buffer Size When the Pause key is pressed, Basic program is executed While 6AUTO Calib is displayed on the LCD Message Display Press the Pause key to enter the Automatic Calibration ModeWhen 6AUTO Calib appears, press the Pause key Automatic CalibrationLAN Setting Time Setting Date SettingCont Real Time Clock Setting 3 Low Battery Check SettingRTC Data Renewal Timing Setting IP Address Setting TCP/IP Feed and Pause keys This parameter is to set a Gateway IP address Printer IP AddressThis parameter is to set an IP address Gateway IP AddressSocket Port Subnet MaskThis parameter is to set a Subnet Mask This parameter is to set a Dhcp client ID This parameter is to enable DhcpDhcp Dhcp Client IDAscii code and Hex. code correspondence table Dhcp Host NameThis parameter is to set a Dhcp host name General Description Installing the Printer DriversInstalling the Printer Driver IntroductionWindows 98/Me E2-47 Windows 2000/XP E2-49 USB Interface E2-51 E2-52 E2-53 Finish button E2-55 E2-56 E2-57 Uninstalling the Printer Driver Adding a LAN Port Windows 98/ME Adding/Deleting a LAN PortDeleting a LAN Port Others Printer Driver UpgradesUsing the Printer Driver Print Test AdjustmentWhen using an optional Cutter Module or Strip Module Position and Print Tone Fine Adjustment Tone Fine When setting +0.0 mmPosition and Print Example of Cut Position Fine Adjustment Example of Strip Position Fine Adjustment Restart Feed When setting +50.0 mm When setting -50.0 mmPosition and Print Tone Fine Adjustment Ribbon Motor Voltage Fine Adjustment Press the Restart key Threshold SettingJam errors Manually setSensor Status Display Black Mark Sensor AdjustmentFeed Gap Sensor Adjustment Black Mark Sensor/Feed Gap Sensor Adjustment No media„ When using the Feed Gap Sensor „ When using the Black Mark SensorPress and hold the Restart or Feed key for about 3 seconds „ Manual Threshold Setting„ Storing a No Media Level Voltage Black Mark Sensor Used to restart printing On Line OperationOperation Panel Used to stop printing temporarilyPress and hold the Restart key for 3 seconds or longer ResetOperation Print Head/Platen/ Sensors MaintenanceCleaning Print Head/Platen/ Sensors Covers and Panels Optional Cutter Module 1. Open the Front Cover Same way, clean the outside of the Cutter BladeGuide Roller Strip Roller Backing Paper Feed Roller Restart key TroubleshootingError Messages Error Messages Problems/Cause Possible Problems Causes Solutions Possible ProblemsRibbon is not loaded properly Load the ribbon properly Cutter blade is dirty Clean the cutter bladeRemoving Jammed Media Model Printer SpecificationsThis section describes the printer specifications Mail 4STATE Customer CODE, RSS14 Label Supply SpecificationsMedia Media TypeTag paper with square holes Detection Area of the Transmissive SensorLabel Effective Print Area Detection Area of the Reflective SensorExample 1 UPM Raflatac’s Rafsec Short Dipole 2 Tag Rfid Tag58mm±6mm 5mm Supply Specifications Ribbon Combination of Media and Ribbon Recommended Media and Ribbon TypesMedia type Description Ribbon type DescriptionCare/Handling of Media and Ribbon Appendix 1 Messages and Leds Symbols in the messageDhcp client is being initialized When the Dhcp function is enabledVoltage of the Real Time Clock Battery Base LAN Board is being initializedFollowing message appears Parallel interface Centronics Appendix 2 InterfacePIN ConnectorLED status Link LED Number of ports Power source Self power Connector Type BNumber of ports Connector RJ-45 StandardEncoding Tag → RW Serial interface OptionWireless LAN Option Expansion I/O Interface Option B-SA704-IO-QM-R At least, 125% of the rated current of the product Appendix 3 Power CordWhen purchasing the power cord Appendix 4 Print Samples Appendix 4 Print Samples EAN13+5 digits Interleaved 2JAN13, EAN13 EAN13+2 digitsKIX Code UPC-A+5 digitsIndustrial 2 Customer bar codeAppendix 5 Glossaries USB Universal Serial Bus Device used to remove labels from the backing paperMedia and ribbon Index Index EO1-33047E
Related manuals
Manual 45 pages 54.11 Kb

BSA4TMTS12QMR, B-SA4TM, B-SA4TM-TS12-QM-R specifications

The Toshiba B-SA4TM-TS12-QM-R is a versatile and high-performance thermal printer designed to meet the demanding needs of various industries, ranging from retail to logistics. Known for its reliability and efficiency, this printer is part of Toshiba's celebrated B-SA4 series that showcases robust engineering and advanced printing technologies.

One of the standout features of the B-SA4TM-TS12-QM-R is its exceptional print speed, capable of reaching up to 152 mm per second. This rapid output ensures that businesses can efficiently manage their printing tasks, reducing wait times and boosting productivity. Its 300 dpi resolution guarantees that printed images and text are sharp and clear, making it ideal for producing high-quality labels, barcodes, and receipts.

The printer is equipped with a user-friendly interface that simplifies operation and maintenance. The LCD screen provides real-time information about printing status and alerts, allowing users to monitor the printer's performance easily. Furthermore, its compact design makes it suitable for environments with limited space while still delivering a robust printing solution.

In terms of connectivity, the B-SA4TM-TS12-QM-R offers multiple options including USB, Ethernet, and serial ports, ensuring that it can easily integrate into existing systems. It also supports a range of operating systems, enhancing its versatility across different hardware environments.

Toshiba has integrated advanced technologies into the B-SA4TM series, such as an innovative ribbon-saving mechanism, which allows for longer print runs without frequent ribbon changes. This feature not only reduces operational costs but also minimizes waste, making it a more environmentally friendly choice.

Additionally, the printer supports a wide variety of media types and sizes, including labels, tags, and wristbands. Its ability to handle diverse materials makes it an excellent choice for businesses that have varied printing needs. The B-SA4TM is also designed for easy media loading, allowing users to change supplies quickly and efficiently.

Overall, the Toshiba B-SA4TM-TS12-QM-R combines speed, quality, and user-friendliness, making it a formidable addition to any business's printing lineup. With its advanced features and robust design, it stands out as a reliable solution for users looking for high-performance thermal printing. Whether it's for shipping, inventory management, or retail operations, the B-SA4TM series delivers exceptional performance that meets the needs of today’s fast-paced environments.