Toshiba BSA4TMTS12QMR, B-SA4TM-TS12-QM-R owner manual How to enter the System Mode

Page 30

2. PRINTER SETUP

ENGLISH VERSION EO1-33047

2.7 Setting an Operating Environment

2.7 Setting an Operating Environment

LCD Message Display

FEED

 

key

 

key

 

PAUSE

 

 

 

 

 

RESTART key

ON LINE

[PAUSE]

PAUSE

Hold down [RESTART] for 3 sec.

<1>RESET

[FEED] [RESTART]

<2>PARAMETER SET

[FEED] [RESTART]

<3>ADJUST SET

[FEED] [RESTART]

<4>DUMP MODE

[FEED] [RESTART]

<5>EXPAND MODE

[FEED] [RESTART]

<6>AUTO CALIB

[FEED] [RESTART]

<7>LAN

[FEED] [RESTART]

<8>RTC SET

[FEED] [RESTART]

Depending on the settings of your host computer or an interface to be used, it may be necessary to change the printer parameter settings.

Follow the procedures described below to change the printer parameter settings in the System Mode to correspond to your environment.

NOTE:

Incorrect settings can cause the printer to function erroneously. If you have any problems with the parameter settings, please contact your nearest TOSHIBA TEC service representative.

For the settings this manual does not cover, please contact your nearest TOSHIBA TEC service representative, or refer to the B-SA4T Series Key Operation Specification stored in the CD-ROM.

How to enter the System Mode

1.Turn on the printer and confirm that “ONLINE” appears on the LCD Message Display.

2.Press the [PAUSE] key to pause the printer.

3.Hold down the [RESTART] key for three seconds until “<1>RESET” is displayed.

The System Mode consists of the following menus.

<1>RESET

This menu is used to clear print data sent from a

 

PC and return the printer to an idle state.

 

Refer to Section 3.3 Reset.

<2>PARAMETER SET

This menu is used to set the printer parameters.

 

Refer to Section 2.7.1 Parameter Setting.

<3>ADJUST SET

This menu is used to make a fine adjustment of a

 

print start position, cut position, etc.

 

Refer to Section 2.10 Position and Print Tone

 

Fine Adjustment.

<4>DUMP MODE

This menu is used to print the data in the receive

 

buffer for debug.

 

Refer to Section 2.7.2 Dump Mode Setting.

<5>EXPAND MODE

This menu is used to start the program for

 

BASIC mode.

 

Refer to Section 2.7.3 BASIC Expansion

 

Mode.

<6>AUTO CALIB

This menu is used to enable or disable the

 

automatic calibration function.

 

Refer to Section 2.7.4 Automatic Calibration.

<7>LAN

This menu is used to enable or disable the LAN

 

communication and SNMP.

 

Refer to Section 2.7.5 LAN Setting.

<8>RTC SET

This menu is used to set the date and time of the

 

real time clock, enable or disable the low battery

 

check, and choose a real time renewal timing.

 

Refer to Section 2.7.6 Real Time Clock

 

Setting.

 

NOTES:

1.System Mode menus can be selected with the [RESTART] or [FEED] key.

2.To enter each of the above System Mode menus, press the [PAUSE] key when the menu is displayed.

3.If the [PAUSE] key is pressed with “<1>RESET” being displayed, the printer will turn to an idle state and the message will change to “ONLINE”

E2-16

Page 29 Page 31
Image 30
Page 29 Page 31
Contents SA4TM Series CE Compliance for EU only VorsichtSA4TM Series Waste Recycling information for users Precautions for Handling of Wireless Communication Device For SafetySafety Summary Meanings of Each SymbolPrecautions Request Regarding MaintenanceTable of Contents EA3-1 EA1-1EA2-1 EA4-1Introduction Features Product OverviewAccessories Front View DimensionsAppearance Rear ViewOperation Panel InteriorOptions Option Name Type UsageProcedure Printer SetupSetup Flow ReferenceAttaching the Printer Rear Support InstallationConnecting the Power Cord Example of US TypeRaise the Release Lever and remove the Media Holder Left Loading the MediaTake out the Media Holder Ass’y from the printer Insert the Media Shaft into the core of a media rollFold the Release Lever to lock the Media Holder Left Place the Media Holder Ass’y into the printerClick Upper Sensor Upper SensorLever Ass’y Setting the Feed Gap Sensor position Setting the Black Mark Sensor position Batch mode Strip mode OptionPress down the Release Bar to open the Strip Unit Cut mode Option Label or Thin mediaTag paper or Thick paper Loading the Ribbon Open the Ribbon Cover Cont Gently close the Top Cover until it clicksConnecting the Printer to Your Host Computer Turning the Printer How to enter the System Mode Time the Pause key is pressed, the sub menus are displayed Parameter SettingWhile 2PARAMETER SET is displayed on the LCD Message SequentiallyUse the Feed or Restart key to select a desired option Character Zero SelectionCharacter Code Selection After selecting a character code, press the Pause keyData Length Selection Baud Rate SelectionAfter selecting a baud rate, press the Pause key After selecting a data length, press the Pause keyStop Bit Length Selection Parity SelectionFlow Control Code Selection Auto Forward Wait Selection LCD Language SelectionAfter selecting a language, press the Pause key After selecting an auto forward wait, press the Pause keyControl Code Selection Feed Key Function Selection Strip Wait Status SelectionAfter selecting the Strip Wait Status, press the Pause key After selecting the Feed key function, press the Pause keyEuro Code Selection Kanji Code SelectionAfter selecting a Kanji code, press the Pause key After selecting a Euro code, press the Pause keyCentronics Interface ACK/BUSY Timing Selection Auto Print Head Check SelectionAfter selecting auto print head check, press the Pause key After selecting an ACK/BUSY timing, press the Pause keyWeb Printer Function Selection Input Prime SelectionAfter selecting the Input Prime, press the Pause key Ribbon Near End Selection Expansion I/O Interface Type SelectionLabel End/Ribbon Error Selection Plug & Play SelectionAfter selecting a Plug & Play, press the Pause key Pre-Strip Selection Maxi Code Specification Selection Reverse Feed Speed SelectionAfter selecting the Back Feed Speed, press the Pause key Strip Motor Torque Selection Keyboard Interface SelectionAfter selecting a keyboard interface, press the Pause key After selecting a strip motor torque, press the Pause keyUse the Feed or Restart key to select a printing method Dump Mode SettingAfter selecting the receive buffer, press the Pause key After selecting a printing method, press the Pause keyData in the receive buffer is printed as follows Receive Buffer SizeRequired Label Length When the Pause key is pressed, Basic program is executed Automatic Calibration Press the Pause key to enter the Automatic Calibration ModeWhen 6AUTO Calib appears, press the Pause key While 6AUTO Calib is displayed on the LCD Message DisplayLAN Setting Date Setting Time SettingReal Time Clock Setting 3 Low Battery Check Setting RTC Data Renewal Timing SettingCont IP Address Setting TCP/IP Feed and Pause keys Gateway IP Address Printer IP AddressThis parameter is to set an IP address This parameter is to set a Gateway IP addressSubnet Mask This parameter is to set a Subnet MaskSocket Port Dhcp Client ID This parameter is to enable DhcpDhcp This parameter is to set a Dhcp client IDDhcp Host Name This parameter is to set a Dhcp host nameAscii code and Hex. code correspondence table Introduction Installing the Printer DriversInstalling the Printer Driver General DescriptionWindows 98/Me E2-47 Windows 2000/XP E2-49 USB Interface E2-51 E2-52 E2-53 Finish button E2-55 E2-56 E2-57 Uninstalling the Printer Driver Adding/Deleting a LAN Port Adding a LAN Port Windows 98/MEDeleting a LAN Port Printer Driver Upgrades OthersUsing the Printer Driver Adjustment Print TestWhen using an optional Cutter Module or Strip Module Position and Print Tone Fine Adjustment When setting +0.0 mm Position and PrintTone Fine Example of Cut Position Fine Adjustment Example of Strip Position Fine Adjustment Restart Feed When setting -50.0 mm When setting +50.0 mmPosition and Print Tone Fine Adjustment Ribbon Motor Voltage Fine Adjustment Manually set Threshold SettingJam errors Press the Restart keyBlack Mark Sensor/Feed Gap Sensor Adjustment No media Black Mark Sensor AdjustmentFeed Gap Sensor Adjustment Sensor Status Display„ When using the Black Mark Sensor „ When using the Feed Gap Sensor„ Manual Threshold Setting „ Storing a No Media Level VoltagePress and hold the Restart or Feed key for about 3 seconds Black Mark Sensor Used to stop printing temporarily On Line OperationOperation Panel Used to restart printingReset OperationPress and hold the Restart key for 3 seconds or longer Maintenance CleaningPrint Head/Platen/ Sensors Print Head/Platen/ Sensors Covers and Panels Same way, clean the outside of the Cutter Blade Optional Cutter Module 1. Open the Front CoverGuide Roller Strip Roller Backing Paper Feed Roller Troubleshooting Error MessagesRestart key Error Messages Problems/Cause Possible Problems Possible Problems Causes SolutionsCutter blade is dirty Clean the cutter blade Removing Jammed MediaRibbon is not loaded properly Load the ribbon properly Printer Specifications This section describes the printer specificationsModel Mail 4STATE Customer CODE, RSS14 Media Type Supply SpecificationsMedia LabelDetection Area of the Transmissive Sensor LabelTag paper with square holes Detection Area of the Reflective Sensor Effective Print AreaRfid Tag Example 1 UPM Raflatac’s Rafsec Short Dipole 2 Tag58mm±6mm 5mm Supply Specifications Ribbon Ribbon type Description Recommended Media and Ribbon TypesMedia type Description Combination of Media and RibbonCare/Handling of Media and Ribbon Symbols in the message Appendix 1 Messages and LedsBase LAN Board is being initialized When the Dhcp function is enabledVoltage of the Real Time Clock Battery Dhcp client is being initializedFollowing message appears Appendix 2 Interface Parallel interface CentronicsConnector PINStandard Number of ports Power source Self power Connector Type BNumber of ports Connector RJ-45 LED status Link LEDSerial interface Option Encoding Tag → RWWireless LAN Option Expansion I/O Interface Option B-SA704-IO-QM-R Appendix 3 Power Cord When purchasing the power cordAt least, 125% of the rated current of the product Appendix 4 Print Samples Appendix 4 Print Samples EAN13+2 digits Interleaved 2JAN13, EAN13 EAN13+5 digitsCustomer bar code UPC-A+5 digitsIndustrial 2 KIX CodeAppendix 5 Glossaries Device used to remove labels from the backing paper Media and ribbonUSB Universal Serial Bus Index Index EO1-33047E
Related manuals
Manual 45 pages 54.11 Kb

BSA4TMTS12QMR, B-SA4TM, B-SA4TM-TS12-QM-R specifications

The Toshiba B-SA4TM-TS12-QM-R is a versatile and high-performance thermal printer designed to meet the demanding needs of various industries, ranging from retail to logistics. Known for its reliability and efficiency, this printer is part of Toshiba's celebrated B-SA4 series that showcases robust engineering and advanced printing technologies.

One of the standout features of the B-SA4TM-TS12-QM-R is its exceptional print speed, capable of reaching up to 152 mm per second. This rapid output ensures that businesses can efficiently manage their printing tasks, reducing wait times and boosting productivity. Its 300 dpi resolution guarantees that printed images and text are sharp and clear, making it ideal for producing high-quality labels, barcodes, and receipts.

The printer is equipped with a user-friendly interface that simplifies operation and maintenance. The LCD screen provides real-time information about printing status and alerts, allowing users to monitor the printer's performance easily. Furthermore, its compact design makes it suitable for environments with limited space while still delivering a robust printing solution.

In terms of connectivity, the B-SA4TM-TS12-QM-R offers multiple options including USB, Ethernet, and serial ports, ensuring that it can easily integrate into existing systems. It also supports a range of operating systems, enhancing its versatility across different hardware environments.

Toshiba has integrated advanced technologies into the B-SA4TM series, such as an innovative ribbon-saving mechanism, which allows for longer print runs without frequent ribbon changes. This feature not only reduces operational costs but also minimizes waste, making it a more environmentally friendly choice.

Additionally, the printer supports a wide variety of media types and sizes, including labels, tags, and wristbands. Its ability to handle diverse materials makes it an excellent choice for businesses that have varied printing needs. The B-SA4TM is also designed for easy media loading, allowing users to change supplies quickly and efficiently.

Overall, the Toshiba B-SA4TM-TS12-QM-R combines speed, quality, and user-friendliness, making it a formidable addition to any business's printing lineup. With its advanced features and robust design, it stands out as a reliable solution for users looking for high-performance thermal printing. Whether it's for shipping, inventory management, or retail operations, the B-SA4TM series delivers exceptional performance that meets the needs of today’s fast-paced environments.
Top Page Image Contents