Toshiba BSA4TMTS12QMR Operation, Reset, Press and hold the Restart key for 3 seconds or longer

Page 93

3. ON LINE OPERATION

ENGLISH VERSION EO1-33047

3.2 Operation

3.2 Operation

NOTES:

1.Description of model name on the 2nd line of the LCD. B-SA4T-T

T: 300 dpi print head

G:203 dpi print head

2.For the meaning of error messages and actions to be taken, refer to Section 5 TROUBLESHOOTING and APPENDIX 1.

When the printer is turned on, the “ON LINE” message appears on the LCD Message Display. It is shown during standby or normal printing.

1.The printer is turned on, standing by, or printing.

ON LINE

B-SA4T-T V1.2A

2.If any error occurs during printing, an error message appears. The printer stops printing automatically. (The number on the right side shows the remaining number of media to be printed.)

NO PAPER

125

B-SA4T-T

V1.2A

3.To clear an error, press the [RESTART] key. The printer resumes printing.

ON LINE

B-SA4T-T V1.2A

4. If the [PAUSE] key is pressed during printing, the printer stops printing temporarily. (The number on the right side shows the remaining number of media to be printed.)

PAUSE 52

B-SA4T-T V1.2A

5.When the [RESTART] key is pressed, the printer resumes printing.

ON LINE

B-SA4T-T V1.2A

3.3 Reset

NOTE:

If the [RESTART] key is held for less than 3 seconds when the printer is in an error or pause state, the printer restarts printing. However, when a communication error or command error occurs, the printer returns to an idle condition.

A reset operation clears the print data sent from the computer to the printer, and returns the printer to an idle condition.

1.The printer is turned on, standing by, or printing.

ON LINE

B-SA4T-T V1.2A

2.To stop printing, or clear the data sent from the computer, press the [PAUSE] key. The printer stops printing.

PAUSE 52

B-SA4T-T V1.2A

3.Press and hold the [RESTART] key for 3 seconds or longer.

<1>RESET

4.Press the [PAUSE] key. The data sent from the computer will be cleared, and the printer returns to an idle condition.

ON LINE

B-SA4T-T V1.2A

E3- 2

Page 92 Page 94
Image 93
Page 92 Page 94
Contents SA4TM Series Vorsicht CE Compliance for EU onlySA4TM Series Waste Recycling information for users For Safety Precautions for Handling of Wireless Communication DeviceMeanings of Each Symbol Safety SummaryRequest Regarding Maintenance PrecautionsTable of Contents EA2-1 EA1-1EA3-1 EA4-1Product Overview Introduction FeaturesAccessories Appearance DimensionsFront View Rear ViewInterior Operation PanelOption Name Type Usage OptionsSetup Flow Printer SetupProcedure ReferenceConnecting the Power Cord InstallationAttaching the Printer Rear Support Example of US TypeTake out the Media Holder Ass’y from the printer Loading the MediaRaise the Release Lever and remove the Media Holder Left Insert the Media Shaft into the core of a media rollPlace the Media Holder Ass’y into the printer Fold the Release Lever to lock the Media Holder LeftClick Upper Sensor Upper SensorLever Ass’y Setting the Feed Gap Sensor position Setting the Black Mark Sensor position Strip mode Option Batch modePress down the Release Bar to open the Strip Unit Cut mode Option Label or Thin mediaTag paper or Thick paper Loading the Ribbon Open the Ribbon Cover Gently close the Top Cover until it clicks ContConnecting the Printer to Your Host Computer Turning the Printer How to enter the System Mode While 2PARAMETER SET is displayed on the LCD Message Parameter SettingTime the Pause key is pressed, the sub menus are displayed SequentiallyCharacter Code Selection Character Zero SelectionUse the Feed or Restart key to select a desired option After selecting a character code, press the Pause keyAfter selecting a baud rate, press the Pause key Baud Rate SelectionData Length Selection After selecting a data length, press the Pause keyStop Bit Length Selection Parity SelectionFlow Control Code Selection After selecting a language, press the Pause key LCD Language SelectionAuto Forward Wait Selection After selecting an auto forward wait, press the Pause keyControl Code Selection After selecting the Strip Wait Status, press the Pause key Strip Wait Status SelectionFeed Key Function Selection After selecting the Feed key function, press the Pause keyAfter selecting a Kanji code, press the Pause key Kanji Code SelectionEuro Code Selection After selecting a Euro code, press the Pause keyAfter selecting auto print head check, press the Pause key Auto Print Head Check SelectionCentronics Interface ACK/BUSY Timing Selection After selecting an ACK/BUSY timing, press the Pause keyWeb Printer Function Selection Input Prime SelectionAfter selecting the Input Prime, press the Pause key Expansion I/O Interface Type Selection Ribbon Near End SelectionLabel End/Ribbon Error Selection Plug & Play SelectionAfter selecting a Plug & Play, press the Pause key Pre-Strip Selection Maxi Code Specification Selection Reverse Feed Speed SelectionAfter selecting the Back Feed Speed, press the Pause key After selecting a keyboard interface, press the Pause key Keyboard Interface SelectionStrip Motor Torque Selection After selecting a strip motor torque, press the Pause keyAfter selecting the receive buffer, press the Pause key Dump Mode SettingUse the Feed or Restart key to select a printing method After selecting a printing method, press the Pause keyData in the receive buffer is printed as follows Receive Buffer SizeRequired Label Length When the Pause key is pressed, Basic program is executed When 6AUTO Calib appears, press the Pause key Press the Pause key to enter the Automatic Calibration ModeAutomatic Calibration While 6AUTO Calib is displayed on the LCD Message DisplayLAN Setting Time Setting Date SettingReal Time Clock Setting 3 Low Battery Check Setting RTC Data Renewal Timing SettingCont IP Address Setting TCP/IP Feed and Pause keys This parameter is to set an IP address Printer IP AddressGateway IP Address This parameter is to set a Gateway IP addressSubnet Mask This parameter is to set a Subnet MaskSocket Port Dhcp This parameter is to enable DhcpDhcp Client ID This parameter is to set a Dhcp client IDDhcp Host Name This parameter is to set a Dhcp host nameAscii code and Hex. code correspondence table Installing the Printer Driver Installing the Printer DriversIntroduction General DescriptionWindows 98/Me E2-47 Windows 2000/XP E2-49 USB Interface E2-51 E2-52 E2-53 Finish button E2-55 E2-56 E2-57 Uninstalling the Printer Driver Adding a LAN Port Windows 98/ME Adding/Deleting a LAN PortDeleting a LAN Port Others Printer Driver UpgradesUsing the Printer Driver Print Test AdjustmentWhen using an optional Cutter Module or Strip Module Position and Print Tone Fine Adjustment When setting +0.0 mm Position and PrintTone Fine Example of Cut Position Fine Adjustment Example of Strip Position Fine Adjustment Restart Feed When setting +50.0 mm When setting -50.0 mmPosition and Print Tone Fine Adjustment Ribbon Motor Voltage Fine Adjustment Jam errors Threshold SettingManually set Press the Restart keyFeed Gap Sensor Adjustment Black Mark Sensor AdjustmentBlack Mark Sensor/Feed Gap Sensor Adjustment No media Sensor Status Display„ When using the Feed Gap Sensor „ When using the Black Mark Sensor„ Manual Threshold Setting „ Storing a No Media Level VoltagePress and hold the Restart or Feed key for about 3 seconds Black Mark Sensor Operation Panel On Line OperationUsed to stop printing temporarily Used to restart printingReset OperationPress and hold the Restart key for 3 seconds or longer Maintenance CleaningPrint Head/Platen/ Sensors Print Head/Platen/ Sensors Covers and Panels Optional Cutter Module 1. Open the Front Cover Same way, clean the outside of the Cutter BladeGuide Roller Strip Roller Backing Paper Feed Roller Troubleshooting Error MessagesRestart key Error Messages Problems/Cause Possible Problems Causes Solutions Possible ProblemsCutter blade is dirty Clean the cutter blade Removing Jammed MediaRibbon is not loaded properly Load the ribbon properly Printer Specifications This section describes the printer specificationsModel Mail 4STATE Customer CODE, RSS14 Media Supply SpecificationsMedia Type LabelDetection Area of the Transmissive Sensor LabelTag paper with square holes Effective Print Area Detection Area of the Reflective SensorExample 1 UPM Raflatac’s Rafsec Short Dipole 2 Tag Rfid Tag58mm±6mm 5mm Supply Specifications Ribbon Media type Description Recommended Media and Ribbon TypesRibbon type Description Combination of Media and RibbonCare/Handling of Media and Ribbon Appendix 1 Messages and Leds Symbols in the messageVoltage of the Real Time Clock Battery When the Dhcp function is enabledBase LAN Board is being initialized Dhcp client is being initializedFollowing message appears Parallel interface Centronics Appendix 2 InterfacePIN ConnectorNumber of ports Connector RJ-45 Number of ports Power source Self power Connector Type BStandard LED status Link LEDEncoding Tag → RW Serial interface OptionWireless LAN Option Expansion I/O Interface Option B-SA704-IO-QM-R Appendix 3 Power Cord When purchasing the power cordAt least, 125% of the rated current of the product Appendix 4 Print Samples Appendix 4 Print Samples JAN13, EAN13 Interleaved 2EAN13+2 digits EAN13+5 digitsIndustrial 2 UPC-A+5 digitsCustomer bar code KIX CodeAppendix 5 Glossaries Device used to remove labels from the backing paper Media and ribbonUSB Universal Serial Bus Index Index EO1-33047E
Related manuals
Manual 45 pages 54.11 Kb

BSA4TMTS12QMR, B-SA4TM, B-SA4TM-TS12-QM-R specifications

The Toshiba B-SA4TM-TS12-QM-R is a versatile and high-performance thermal printer designed to meet the demanding needs of various industries, ranging from retail to logistics. Known for its reliability and efficiency, this printer is part of Toshiba's celebrated B-SA4 series that showcases robust engineering and advanced printing technologies.

One of the standout features of the B-SA4TM-TS12-QM-R is its exceptional print speed, capable of reaching up to 152 mm per second. This rapid output ensures that businesses can efficiently manage their printing tasks, reducing wait times and boosting productivity. Its 300 dpi resolution guarantees that printed images and text are sharp and clear, making it ideal for producing high-quality labels, barcodes, and receipts.

The printer is equipped with a user-friendly interface that simplifies operation and maintenance. The LCD screen provides real-time information about printing status and alerts, allowing users to monitor the printer's performance easily. Furthermore, its compact design makes it suitable for environments with limited space while still delivering a robust printing solution.

In terms of connectivity, the B-SA4TM-TS12-QM-R offers multiple options including USB, Ethernet, and serial ports, ensuring that it can easily integrate into existing systems. It also supports a range of operating systems, enhancing its versatility across different hardware environments.

Toshiba has integrated advanced technologies into the B-SA4TM series, such as an innovative ribbon-saving mechanism, which allows for longer print runs without frequent ribbon changes. This feature not only reduces operational costs but also minimizes waste, making it a more environmentally friendly choice.

Additionally, the printer supports a wide variety of media types and sizes, including labels, tags, and wristbands. Its ability to handle diverse materials makes it an excellent choice for businesses that have varied printing needs. The B-SA4TM is also designed for easy media loading, allowing users to change supplies quickly and efficiently.

Overall, the Toshiba B-SA4TM-TS12-QM-R combines speed, quality, and user-friendliness, making it a formidable addition to any business's printing lineup. With its advanced features and robust design, it stands out as a reliable solution for users looking for high-performance thermal printing. Whether it's for shipping, inventory management, or retail operations, the B-SA4TM series delivers exceptional performance that meets the needs of today’s fast-paced environments.
Top Page Image Contents