Toshiba B-SA4TM-TS12-QM-R, BSA4TMTS12QMR owner manual Supply Specifications

Page 110

7. SUPPLY SPECIFICATIONS

ENGLISH VERSION EO1-33047

7.1 Media

(7) Printing on Bump (Chip/Antenna) Area

Embedding an RFID tag in labels creates bumps on the label surface, causing incomplete printing.

Uneven printing or incomplete printing can occur easily, especially within 5 mm back and forth and right and left sides of the RFID-tag embedded area, as shown in the figure below.

NOTE: The degree of poor printing quality differs depending on height of a chip/antenna used.

RFID tag embedded area

Print quality on the IC chip is not guaranteed.

5mm

Print quality on bumps is not guaranteed.

Print quality on the sides of RFID tag is not guaranteed.

Media feed direction

5mm

Print quality on bumps is not guaranteed.

(8) Ambient Temperature

As low temperature deteriorates wireless performance, writing data on an RFID tag may fail under such conditions.

(9) Strip Issue

Stripping performance in strip issue mode depends on the type of glue, tag, and backing paper. For some RFID supplies used, a strip issue may not be performed properly.

(10) Caution for Minimum Label Pitch Length

When media, of which label pitch length is short, is used, data may be written on an RFID tag next to the target RFID tag.

As the location, where data is to be written, differs among RFID tag types, a check must be performed to make sure that the data is written on the target RFID tags. The B-SX RFID Analyze Tool can be used for this purpose. For details, please contact the nearest TOSHIBA TEC service representative.

E7- 7

Page 109 Page 111
Image 110
Page 109 Page 111
Contents SA4TM Series CE Compliance for EU only VorsichtSA4TM Series Waste Recycling information for users Precautions for Handling of Wireless Communication Device For SafetySafety Summary Meanings of Each SymbolPrecautions Request Regarding MaintenanceTable of Contents EA3-1 EA1-1EA2-1 EA4-1Introduction Features Product OverviewAccessories Front View DimensionsAppearance Rear ViewOperation Panel InteriorOptions Option Name Type UsageProcedure Printer SetupSetup Flow ReferenceAttaching the Printer Rear Support InstallationConnecting the Power Cord Example of US TypeRaise the Release Lever and remove the Media Holder Left Loading the MediaTake out the Media Holder Ass’y from the printer Insert the Media Shaft into the core of a media rollFold the Release Lever to lock the Media Holder Left Place the Media Holder Ass’y into the printerClick Upper Sensor Upper SensorLever Ass’y Setting the Feed Gap Sensor position Setting the Black Mark Sensor position Batch mode Strip mode OptionPress down the Release Bar to open the Strip Unit Tag paper or Thick paper Cut mode OptionLabel or Thin media Loading the Ribbon Open the Ribbon Cover Cont Gently close the Top Cover until it clicksConnecting the Printer to Your Host Computer Turning the Printer How to enter the System Mode Time the Pause key is pressed, the sub menus are displayed Parameter SettingWhile 2PARAMETER SET is displayed on the LCD Message SequentiallyUse the Feed or Restart key to select a desired option Character Zero SelectionCharacter Code Selection After selecting a character code, press the Pause keyData Length Selection Baud Rate SelectionAfter selecting a baud rate, press the Pause key After selecting a data length, press the Pause keyFlow Control Code Selection Stop Bit Length SelectionParity Selection Auto Forward Wait Selection LCD Language SelectionAfter selecting a language, press the Pause key After selecting an auto forward wait, press the Pause keyControl Code Selection Feed Key Function Selection Strip Wait Status SelectionAfter selecting the Strip Wait Status, press the Pause key After selecting the Feed key function, press the Pause keyEuro Code Selection Kanji Code SelectionAfter selecting a Kanji code, press the Pause key After selecting a Euro code, press the Pause keyCentronics Interface ACK/BUSY Timing Selection Auto Print Head Check SelectionAfter selecting auto print head check, press the Pause key After selecting an ACK/BUSY timing, press the Pause keyAfter selecting the Input Prime, press the Pause key Web Printer Function SelectionInput Prime Selection Ribbon Near End Selection Expansion I/O Interface Type SelectionAfter selecting a Plug & Play, press the Pause key Label End/Ribbon Error SelectionPlug & Play Selection Pre-Strip Selection After selecting the Back Feed Speed, press the Pause key Maxi Code Specification SelectionReverse Feed Speed Selection Strip Motor Torque Selection Keyboard Interface SelectionAfter selecting a keyboard interface, press the Pause key After selecting a strip motor torque, press the Pause keyUse the Feed or Restart key to select a printing method Dump Mode SettingAfter selecting the receive buffer, press the Pause key After selecting a printing method, press the Pause keyRequired Label Length Data in the receive buffer is printed as followsReceive Buffer Size When the Pause key is pressed, Basic program is executed Automatic Calibration Press the Pause key to enter the Automatic Calibration ModeWhen 6AUTO Calib appears, press the Pause key While 6AUTO Calib is displayed on the LCD Message DisplayLAN Setting Date Setting Time SettingCont Real Time Clock Setting 3 Low Battery Check SettingRTC Data Renewal Timing Setting IP Address Setting TCP/IP Feed and Pause keys Gateway IP Address Printer IP AddressThis parameter is to set an IP address This parameter is to set a Gateway IP addressSocket Port Subnet MaskThis parameter is to set a Subnet Mask Dhcp Client ID This parameter is to enable DhcpDhcp This parameter is to set a Dhcp client IDAscii code and Hex. code correspondence table Dhcp Host NameThis parameter is to set a Dhcp host name Introduction Installing the Printer DriversInstalling the Printer Driver General DescriptionWindows 98/Me E2-47 Windows 2000/XP E2-49 USB Interface E2-51 E2-52 E2-53 Finish button E2-55 E2-56 E2-57 Uninstalling the Printer Driver Adding/Deleting a LAN Port Adding a LAN Port Windows 98/MEDeleting a LAN Port Printer Driver Upgrades OthersUsing the Printer Driver Adjustment Print TestWhen using an optional Cutter Module or Strip Module Position and Print Tone Fine Adjustment Tone Fine When setting +0.0 mmPosition and Print Example of Cut Position Fine Adjustment Example of Strip Position Fine Adjustment Restart Feed When setting -50.0 mm When setting +50.0 mmPosition and Print Tone Fine Adjustment Ribbon Motor Voltage Fine Adjustment Manually set Threshold SettingJam errors Press the Restart keyBlack Mark Sensor/Feed Gap Sensor Adjustment No media Black Mark Sensor AdjustmentFeed Gap Sensor Adjustment Sensor Status Display„ When using the Black Mark Sensor „ When using the Feed Gap SensorPress and hold the Restart or Feed key for about 3 seconds „ Manual Threshold Setting„ Storing a No Media Level Voltage Black Mark Sensor Used to stop printing temporarily On Line OperationOperation Panel Used to restart printingPress and hold the Restart key for 3 seconds or longer ResetOperation Print Head/Platen/ Sensors MaintenanceCleaning Print Head/Platen/ Sensors Covers and Panels Same way, clean the outside of the Cutter Blade Optional Cutter Module 1. Open the Front CoverGuide Roller Strip Roller Backing Paper Feed Roller Restart key TroubleshootingError Messages Error Messages Problems/Cause Possible Problems Possible Problems Causes SolutionsRibbon is not loaded properly Load the ribbon properly Cutter blade is dirty Clean the cutter bladeRemoving Jammed Media Model Printer SpecificationsThis section describes the printer specifications Mail 4STATE Customer CODE, RSS14 Media Type Supply SpecificationsMedia LabelTag paper with square holes Detection Area of the Transmissive SensorLabel Detection Area of the Reflective Sensor Effective Print AreaRfid Tag Example 1 UPM Raflatac’s Rafsec Short Dipole 2 Tag58mm±6mm 5mm Supply Specifications Ribbon Ribbon type Description Recommended Media and Ribbon TypesMedia type Description Combination of Media and RibbonCare/Handling of Media and Ribbon Symbols in the message Appendix 1 Messages and LedsBase LAN Board is being initialized When the Dhcp function is enabledVoltage of the Real Time Clock Battery Dhcp client is being initializedFollowing message appears Appendix 2 Interface Parallel interface CentronicsConnector PINStandard Number of ports Power source Self power Connector Type BNumber of ports Connector RJ-45 LED status Link LEDSerial interface Option Encoding Tag → RWWireless LAN Option Expansion I/O Interface Option B-SA704-IO-QM-R At least, 125% of the rated current of the product Appendix 3 Power CordWhen purchasing the power cord Appendix 4 Print Samples Appendix 4 Print Samples EAN13+2 digits Interleaved 2JAN13, EAN13 EAN13+5 digitsCustomer bar code UPC-A+5 digitsIndustrial 2 KIX CodeAppendix 5 Glossaries USB Universal Serial Bus Device used to remove labels from the backing paperMedia and ribbon Index Index EO1-33047E
Related manuals
Manual 45 pages 54.11 Kb

BSA4TMTS12QMR, B-SA4TM, B-SA4TM-TS12-QM-R specifications

The Toshiba B-SA4TM-TS12-QM-R is a versatile and high-performance thermal printer designed to meet the demanding needs of various industries, ranging from retail to logistics. Known for its reliability and efficiency, this printer is part of Toshiba's celebrated B-SA4 series that showcases robust engineering and advanced printing technologies.

One of the standout features of the B-SA4TM-TS12-QM-R is its exceptional print speed, capable of reaching up to 152 mm per second. This rapid output ensures that businesses can efficiently manage their printing tasks, reducing wait times and boosting productivity. Its 300 dpi resolution guarantees that printed images and text are sharp and clear, making it ideal for producing high-quality labels, barcodes, and receipts.

The printer is equipped with a user-friendly interface that simplifies operation and maintenance. The LCD screen provides real-time information about printing status and alerts, allowing users to monitor the printer's performance easily. Furthermore, its compact design makes it suitable for environments with limited space while still delivering a robust printing solution.

In terms of connectivity, the B-SA4TM-TS12-QM-R offers multiple options including USB, Ethernet, and serial ports, ensuring that it can easily integrate into existing systems. It also supports a range of operating systems, enhancing its versatility across different hardware environments.

Toshiba has integrated advanced technologies into the B-SA4TM series, such as an innovative ribbon-saving mechanism, which allows for longer print runs without frequent ribbon changes. This feature not only reduces operational costs but also minimizes waste, making it a more environmentally friendly choice.

Additionally, the printer supports a wide variety of media types and sizes, including labels, tags, and wristbands. Its ability to handle diverse materials makes it an excellent choice for businesses that have varied printing needs. The B-SA4TM is also designed for easy media loading, allowing users to change supplies quickly and efficiently.

Overall, the Toshiba B-SA4TM-TS12-QM-R combines speed, quality, and user-friendliness, making it a formidable addition to any business's printing lineup. With its advanced features and robust design, it stands out as a reliable solution for users looking for high-performance thermal printing. Whether it's for shipping, inventory management, or retail operations, the B-SA4TM series delivers exceptional performance that meets the needs of today’s fast-paced environments.
Top Page Image Contents