Specifications, General | KitchenAid KAD-9 specs

SPECIFICATIONS
Electrical:
Electrical Supply	110 - 120 VAC, 60 Hz
Dual Dishwasher
Motor Load	3.1 amperes
Total Load	9.2 amperes
General:
Wash / Drain Pump Motor	60 Watts
Water Level In Tank	1/2″
Heater Element	650 Watts
Supply Water Flow Rate To Fill	.65 gallons (2.5 liters) per minute
Supply Water Pressure	4.3 - 145 psi (30 kPa min - 1000 kPa max)
Supply Water Temperature	120°F (48.8°C)
Dish Rack	Nylon
Dimensions:
Dual Dishwasher	32-1/4″to 34-1/4″(819.4 to 869.4 mm)
Height	32-1/4″to 34-1/4″(819.4 to 869.4 mm)
Width	23-7/16″(595 mm)
Depth	22-7/16″(570 mm)
Minimum Front Panel (2) Height	28-1/4″(717.5 mm)
Weight	124 lbs.
Cavity	32-5/16″(820 mm)
Height	32-5/16″(820 mm)
Width	23-5/8″(600 mm)
Depth	22-7/8″(580 mm)

1-4

Image 8

KitchenAid KAD-9 manual Specifications, General

Contents

Drawer Dishwasher Forward Goals and Objectives Table of Contents Diagnostics & Troubleshooting Safety First General Model & Serial Number Designations Model NumberSerial Number D D 01 D P PA Model & Serial Number Label Tech Sheet Locations Specifications General KitchenAid will not pay for Kitchenaid Dishwasher WarrantyTWO-YEAR Full Warranty Page Parts Supplied GeneralTools and Material Required Product Dimensions 32-3/16 34-1/2 Cm 87.8 cm Cabinet Dimensions / Requirements From front Electrical Requirements Water RequirementsRecommended Ground Method Foragrounded,cord-connecteddishwasher Installing the Dishwasher Power Supply Cord Side Extrusion Chassis Trim Edge Lip Top extrusion Direct Wiring Remove the house wiring knockout Side Mounting the Dishwasher Top attaching bracket Drain hose support Waste 27-1/2 32-1/4 For standpipe installations Other Plumbing Options Standard Toe Kick Front Panels & TOE KickStandard Front Panels Toe kick Custom Front Panels Dimensions Custom Front Panels Lay the custom front panel face down Custom Toe Kick Dimensions Custom Toe Kick System Overview Drain Cycle Filter PlateDrying Cycle LID System Parts and Features Control Panels Wash System To Clean The Spray ArmDishwasher Systems To Clean The Drain Filter To Clean The Filter PlateSound System Drying System Filling The Powdered Detergent Dispenser Using the DishwasherDetergent USE How Much Detergent To Use Program Quantities Rinse Aid Indicator Rinse AID DispenserFilling The Dispenser How Much Rinse Aid To Use Performance Tips Program Charts Wash Programs Canceling a Wash Cycle Pausing a CycleChanging a Cycle Or Setting Option Selections Adjustments Delay Start Mode To enter the Option Adjustment ModeTo adjust the Rinse Aid setting Control Lock To disable the Auto Power To disable the End of Wash Program beepsPage Component Locations In-Tub ComponentsTub-Mounted Components Cabinet-Mounted Components Removing the Spray ARM and Impeller On the next Removing the ISOLATOR, BADGE, & Door HandleTo remove the isolator Inner Door Panel Slide Down & Lift Pry Inner Door Panel Up Removing the Drying FAN and Rinse AID LED Slide the rinse aid LED out of its holder Removing the Controller Removing the Rinse AID Detergent Dispenser Removing the Upper or Lower Drawer Rail Air Cover Tab To remove the hall sensor Reassembly Notes Removing the LID Removing the LID Motors To remove the chassis module Removing the Chassis Module and Power CordTo remove the power cord Removing the Water Fill Valves Component Testing Drying FAN Rinse AID and Detergent Dispenser Wash & Drain Motor To test the heater, touch the ohmmeter Power Resistor & HeaterLID Motor Temperature Sensor Water Fill Valves Diagnostics Error Code Display Mode Error Codes Temperature Sensor Failed Bad Wiring Or ConnectionsMoisture / Foreign Matter On Chassis Board Flood Switch PCB Failed Heater Element Moisture Around Temperature Sensor Wiring Or Connections BadWater Supply Valve Turned Off Inlet Valve Failed Diagnostic Modes Hardware Output TestTub Home Sensor Test Fast Test Cycle Troubleshooting Chart Resistance Checks Wiring Diagram Page Product Specifications Warranty Information Sources United States