Manuals / Brands / Kitchen Appliance / Dishwasher / KitchenAid / Kitchen Appliance / Dishwasher

KitchenAid KAD-9 REMOVING THE HALL SENSOR, THE WASH AND DRAIN MOTOR, AND THE HEATER ELEMENT ASSEMBLY

1 72

Download 72 pages, 49.15 Mb

4-10

REMOVING THE HALL SENSOR, THE WASH ANDDRAIN MOTOR, AND THE HEATER ELEMENT ASSEMBLY

1. Unplug dishwasher or disconnect power.

2. Turn off the water going to the dishwasher.

3. Disconnect the drain line from the dish-

washer.

4. Remove the dishwasher drawer and turn

it over (see page 4-9 for the procedure).

5. Unclip the locking tab from the air cover,

slide it forward off the rails, and remove

the cover.

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before

operating.

Failure to do so can result in death or

electrical shock.

WARNING

Wiring Cover

Unsnap Arm Unsnap Arm

6. Use a screwdriver and unsnap the under-

side of the wiring cover arms, and remove

the cover from the bottom of the drawer.

7. Wedge a screwdriver blade into the three

top slots of the wiring cover and unsnap

the cover from the motor housing.

Air Cover

Tab

Rail Rail

Slot

Hall

Sensor

Wash &

Drain Motor

Heater

Element

Assembly

Contents

Main - ii - FORWARD GOALS AND OBJECTIVES - iii - TABLE OF CONTENTS Page 1-1 GENERAL SAFETY FIRST Your safety and the safety of others is very important. DANGER WARNING 1-2 MODEL & SERIAL NUMBER DESIGNATIONS SERIAL NUMBER MODEL NUMBER Page 1-4 SPECIFICATIONS 1-5 KITCHENAID DISHWASHER WARRANTY TWO-YEAR FULL WARRANTY Page 2-1 INSTALLATION INFORMATION GENERAL TOOLS AND MATERIAL REQUIRED PARTS SUPPLIED 2-2 PRODUCT DIMENSIONS 2-3 CABINET DIMENSIONS / REQUIREMENTS 2-4 ELECTRICAL REQUIREMENTS WATER REQUIREMENTS 2-5 INSTALLING THE DISHWASHER POWER SUPPLY CORD 2-6 2-7 DIRECT WIRING 2-8 2-9 2-10 MOUNTING THE DISHWASHER 2-11 2-12 2-13 2-14 FRONT PANELS & TOE KICK 2-15 2-16 Top panel Medallion cutout Bottom panel Custom Front Panels Dimensions 2-17 2-18 Custom Toe Kick Dimensions 3-1 PRODUCT OPERATION SYSTEM OVERVIEW ELECTRONICS MOTOR & HALL SENSOR HEATER PLATE 3-2 DRAIN CYCLE FILTER PLATE DRYING CYCLE LID SYSTEM PARTS AND FEATURES The features on your dishwasher may vary from those shown below. CONTROL PANELS 3-4 THE WASH SYSTEM DISHWASHER SYSTEMS Cleaning The Spray Arm, Drain Filter, And Filter Plate 3-5 THE SOUND SYSTEM THE DRYING SYSTEM 3-6 USING THE DISHWASHER DETERGENT USE 3-7 3-8 RINSE AID DISPENSER 3-9 PERFORMANCE TIPS 3-10 WASH PROGRAMS PROGRAM CHARTS program description program description NOTE: Wash times can vary depending on the incoming water temperature, type of dishload, and whether the drawer has been opened during the wash. 3-11 CANCELING A WASH CYCLE PAUSING A CYCLE CHANGING A CYCLE OR SETTING ADDING ITEMS DURING A CYCLE 3-12 3-13 Page 4-1 COMPONENT ACCESS COMPONENT LOCATIONS 4-2 REMOVING THE SPRAY ARM AND IMPELLER 4-3 REMOVING THE ISOLATOR, BADGE, & DOOR HANDLE 4-4 4-5 REMOVING THE DRYING FAN AND RINSE AID LED 4-6 4-7 REMOVING THE CONTROLLER 4-8 REMOVING THE RINSE AID AND DETERGENT DISPENSER 4-9 REMOVING THE UPPER OR LOWER DRAWER 4-10 REMOVING THE HALL SENSOR, THE WASH AND DRAIN MOTOR, AND THE HEATER ELEMENT ASSEMBLY 4-11 4-12 4-13 REMOVING THE LID 4-14 REMOVING THE LID MOTORS 4-15 REMOVING THE CHASSIS MODULE AND POWER CORD 4-16 REMOVING THE WATER FILL VALVES 5-1 COMPONENT TESTING DRYING FAN 5-2 RINSE AID AND DETERGENT DISPENSER WASH & DRAIN MOTOR 5-3 POWER RESISTOR & HEATER LID MOTOR 5-4 TEMPERATURE SENSOR WATER FILL VALVES 6-1 DIAGNOSTICS & TROUBLESHOOTING DIAGNOSTICS THE ERROR CODE DISPLAY MODE 6-2 ERROR CODES 6-3 6-4 6-5 DIAGNOSTIC MODES 6-6 TROUBLESHOOTING CHART 7-1 WIRING DIAGRAM MM Harness Chassis Fuse Page PRODUCT SPECIFICATIONS AND WARRANTY INFORMATION SOURCES