Component Locations, In-Tub Components | KitchenAid KAD-9 specs

COMPONENT ACCESS

This section instructs you on how to service each component inside the Drawer Dishwasher. The components and their locations are shown below.

COMPONENT LOCATIONS

In-Tub Components

Spray Arm

Impeller

Coarse Filter

Hall Sensor

Heater Element

Drying Fan

Controller

Wash & Drain Motor

Rinse Aid LED

Rinse Aid & Detergent

Dispenser Pumps

Tub-Mounted Components

Water Fill

Valve

	Lid Motor	Power Cord
	(1 of 4)	Power Cord
	(1 of 4)

Chassis

Module

Cabinet-Mounted Components

4-1

Image 43

KitchenAid KAD-9 manual Component Locations, In-Tub Components, Tub-Mounted Components, Cabinet-Mounted Components

Contents

Drawer Dishwasher Goals and Objectives Forward Table of Contents Diagnostics & Troubleshooting General Safety First D D 01 D P PA Model & Serial Number DesignationsModel Number Serial Number Model & Serial Number Label Tech Sheet Locations General Specifications TWO-YEAR Full Warranty Kitchenaid Dishwasher WarrantyKitchenAid will not pay for Page Tools and Material Required GeneralParts Supplied 32-3/16 34-1/2 Cm 87.8 cm Product Dimensions From front Cabinet Dimensions / Requirements Foragrounded,cord-connecteddishwasher Electrical RequirementsWater Requirements Recommended Ground Method Power Supply Cord Installing the Dishwasher Side Extrusion Chassis Trim Edge Lip Top extrusion Direct Wiring Remove the house wiring knockout Side Mounting the Dishwasher Top attaching bracket Drain hose support Waste 27-1/2 32-1/4 Other Plumbing Options For standpipe installations Standard Front Panels Front Panels & TOE KickStandard Toe Kick Toe kick Custom Front Panels Custom Front Panels Dimensions Lay the custom front panel face down Custom Toe Kick Custom Toe Kick Dimensions System Overview LID System Drain CycleFilter Plate Drying Cycle Control Panels Parts and Features Dishwasher Systems To Clean The Spray ArmWash System Drying System To Clean The Drain FilterTo Clean The Filter Plate Sound System Detergent USE Using the DishwasherFilling The Powdered Detergent Dispenser Program Quantities How Much Detergent To Use How Much Rinse Aid To Use Rinse Aid IndicatorRinse AID Dispenser Filling The Dispenser Performance Tips Wash Programs Program Charts Option Selections Adjustments Canceling a Wash CyclePausing a Cycle Changing a Cycle Or Setting Control Lock Delay Start ModeTo enter the Option Adjustment Mode To adjust the Rinse Aid setting To disable the End of Wash Program beeps To disable the Auto PowerPage Cabinet-Mounted Components Component LocationsIn-Tub Components Tub-Mounted Components Removing the Spray ARM and Impeller To remove the isolator Removing the ISOLATOR, BADGE, & Door HandleOn the next Inner Door Panel Slide Down & Lift Pry Inner Door Panel Up Removing the Drying FAN and Rinse AID LED Slide the rinse aid LED out of its holder Removing the Controller Removing the Rinse AID Detergent Dispenser Removing the Upper or Lower Drawer Rail Air Cover Tab To remove the hall sensor Reassembly Notes Removing the LID Removing the LID Motors To remove the power cord Removing the Chassis Module and Power CordTo remove the chassis module Removing the Water Fill Valves Drying FAN Component Testing Wash & Drain Motor Rinse AID and Detergent Dispenser LID Motor Power Resistor & HeaterTo test the heater, touch the ohmmeter Water Fill Valves Temperature Sensor Error Code Display Mode Diagnostics Error Codes Failed Heater Element Temperature Sensor FailedBad Wiring Or Connections Moisture / Foreign Matter On Chassis Board Flood Switch PCB Inlet Valve Failed Moisture Around Temperature SensorWiring Or Connections Bad Water Supply Valve Turned Off Fast Test Cycle Diagnostic ModesHardware Output Test Tub Home Sensor Test Resistance Checks Troubleshooting Chart Wiring Diagram Page United States Product Specifications Warranty Information Sources