Toshiba B-SA4TM-TS12-QM-R, BSA4TMTS12QMR Position and Print, Tone Fine, When setting +0.0 mm

Page 80

2. PRINTER SETUP

ENGLISH VERSION EO1-33047

2.10 Position and Print Tone Fine Adjustment

2.10 Position and Print

Tone Fine

Adjustment (Cont.)

Print Start Position Fine Adjustment

NOTES:

Choose a desired value by using the [RESTART] or [FEED] key.

Pressing the [FEED] key one time causes a –0.1mm change, up to –50.0 mm.

Pressing the [RESTART] key one time causes a +0.1mm change, up to +50.0 mm.

[RESTART]

[FEED]

<3>ADJUST SET FEED ADJ.+10.0mm

FEED ADJ.+50.0mm

FEED ADJ.+49.9mm

FEED ADJ.+0.1mm

FEED ADJ.+0.0mm

FEED ADJ.-0.1mm

FEED ADJ.-49.9mm

FEED ADJ.-50.0mm

After selecting a fine adjustment value, press the [PAUSE] key.

•Example of Print Start Position Fine Adjustment

When setting +3.0 mm

Compared with “+0.0mm” position, the print start position is shifted forward.

Feed Direction

One label

Print Start Position

3mm

When setting +0.0 mm

Feed Direction

When setting –3.0 mm

Compared with “+0.0mm” position, the print start position is shifted backward.

Feed Direction

One label Print Start Position

3mm

One label

Print Start Position

E2-66

Page 79 Page 81
Image 80
Page 79 Page 81
Contents SA4TM Series CE Compliance for EU only VorsichtSA4TM Series Waste Recycling information for users Precautions for Handling of Wireless Communication Device For SafetySafety Summary Meanings of Each SymbolPrecautions Request Regarding MaintenanceTable of Contents EA1-1 EA2-1EA3-1 EA4-1Introduction Features Product OverviewAccessories Dimensions AppearanceFront View Rear ViewOperation Panel InteriorOptions Option Name Type UsagePrinter Setup Setup FlowProcedure ReferenceInstallation Connecting the Power CordAttaching the Printer Rear Support Example of US TypeLoading the Media Take out the Media Holder Ass’y from the printerRaise the Release Lever and remove the Media Holder Left Insert the Media Shaft into the core of a media rollFold the Release Lever to lock the Media Holder Left Place the Media Holder Ass’y into the printerClick Upper Sensor Upper SensorLever Ass’y Setting the Feed Gap Sensor position Setting the Black Mark Sensor position Batch mode Strip mode OptionPress down the Release Bar to open the Strip Unit Tag paper or Thick paper Cut mode OptionLabel or Thin media Loading the Ribbon Open the Ribbon Cover Cont Gently close the Top Cover until it clicksConnecting the Printer to Your Host Computer Turning the Printer How to enter the System Mode Parameter Setting While 2PARAMETER SET is displayed on the LCD MessageTime the Pause key is pressed, the sub menus are displayed SequentiallyCharacter Zero Selection Character Code SelectionUse the Feed or Restart key to select a desired option After selecting a character code, press the Pause keyBaud Rate Selection After selecting a baud rate, press the Pause keyData Length Selection After selecting a data length, press the Pause keyFlow Control Code Selection Stop Bit Length SelectionParity Selection LCD Language Selection After selecting a language, press the Pause keyAuto Forward Wait Selection After selecting an auto forward wait, press the Pause keyControl Code Selection Strip Wait Status Selection After selecting the Strip Wait Status, press the Pause keyFeed Key Function Selection After selecting the Feed key function, press the Pause keyKanji Code Selection After selecting a Kanji code, press the Pause keyEuro Code Selection After selecting a Euro code, press the Pause keyAuto Print Head Check Selection After selecting auto print head check, press the Pause keyCentronics Interface ACK/BUSY Timing Selection After selecting an ACK/BUSY timing, press the Pause keyAfter selecting the Input Prime, press the Pause key Web Printer Function SelectionInput Prime Selection Ribbon Near End Selection Expansion I/O Interface Type SelectionAfter selecting a Plug & Play, press the Pause key Label End/Ribbon Error SelectionPlug & Play Selection Pre-Strip Selection After selecting the Back Feed Speed, press the Pause key Maxi Code Specification SelectionReverse Feed Speed Selection Keyboard Interface Selection After selecting a keyboard interface, press the Pause keyStrip Motor Torque Selection After selecting a strip motor torque, press the Pause keyDump Mode Setting After selecting the receive buffer, press the Pause keyUse the Feed or Restart key to select a printing method After selecting a printing method, press the Pause keyRequired Label Length Data in the receive buffer is printed as followsReceive Buffer Size When the Pause key is pressed, Basic program is executed Press the Pause key to enter the Automatic Calibration Mode When 6AUTO Calib appears, press the Pause keyAutomatic Calibration While 6AUTO Calib is displayed on the LCD Message DisplayLAN Setting Date Setting Time SettingCont Real Time Clock Setting 3 Low Battery Check SettingRTC Data Renewal Timing Setting IP Address Setting TCP/IP Feed and Pause keys Printer IP Address This parameter is to set an IP addressGateway IP Address This parameter is to set a Gateway IP addressSocket Port Subnet MaskThis parameter is to set a Subnet Mask This parameter is to enable Dhcp DhcpDhcp Client ID This parameter is to set a Dhcp client IDAscii code and Hex. code correspondence table Dhcp Host NameThis parameter is to set a Dhcp host name Installing the Printer Drivers Installing the Printer DriverIntroduction General DescriptionWindows 98/Me E2-47 Windows 2000/XP E2-49 USB Interface E2-51 E2-52 E2-53 Finish button E2-55 E2-56 E2-57 Uninstalling the Printer Driver Adding/Deleting a LAN Port Adding a LAN Port Windows 98/MEDeleting a LAN Port Printer Driver Upgrades OthersUsing the Printer Driver Adjustment Print TestWhen using an optional Cutter Module or Strip Module Position and Print Tone Fine Adjustment Tone Fine When setting +0.0 mmPosition and Print Example of Cut Position Fine Adjustment Example of Strip Position Fine Adjustment Restart Feed When setting -50.0 mm When setting +50.0 mmPosition and Print Tone Fine Adjustment Ribbon Motor Voltage Fine Adjustment Threshold Setting Jam errorsManually set Press the Restart keyBlack Mark Sensor Adjustment Feed Gap Sensor AdjustmentBlack Mark Sensor/Feed Gap Sensor Adjustment No media Sensor Status Display„ When using the Black Mark Sensor „ When using the Feed Gap SensorPress and hold the Restart or Feed key for about 3 seconds „ Manual Threshold Setting„ Storing a No Media Level Voltage Black Mark Sensor On Line Operation Operation PanelUsed to stop printing temporarily Used to restart printingPress and hold the Restart key for 3 seconds or longer ResetOperation Print Head/Platen/ Sensors MaintenanceCleaning Print Head/Platen/ Sensors Covers and Panels Same way, clean the outside of the Cutter Blade Optional Cutter Module 1. Open the Front CoverGuide Roller Strip Roller Backing Paper Feed Roller Restart key TroubleshootingError Messages Error Messages Problems/Cause Possible Problems Possible Problems Causes SolutionsRibbon is not loaded properly Load the ribbon properly Cutter blade is dirty Clean the cutter bladeRemoving Jammed Media Model Printer SpecificationsThis section describes the printer specifications Mail 4STATE Customer CODE, RSS14 Supply Specifications MediaMedia Type LabelTag paper with square holes Detection Area of the Transmissive SensorLabel Detection Area of the Reflective Sensor Effective Print AreaRfid Tag Example 1 UPM Raflatac’s Rafsec Short Dipole 2 Tag58mm±6mm 5mm Supply Specifications Ribbon Recommended Media and Ribbon Types Media type DescriptionRibbon type Description Combination of Media and RibbonCare/Handling of Media and Ribbon Symbols in the message Appendix 1 Messages and LedsWhen the Dhcp function is enabled Voltage of the Real Time Clock BatteryBase LAN Board is being initialized Dhcp client is being initializedFollowing message appears Appendix 2 Interface Parallel interface CentronicsConnector PINNumber of ports Power source Self power Connector Type B Number of ports Connector RJ-45Standard LED status Link LEDSerial interface Option Encoding Tag → RWWireless LAN Option Expansion I/O Interface Option B-SA704-IO-QM-R At least, 125% of the rated current of the product Appendix 3 Power CordWhen purchasing the power cord Appendix 4 Print Samples Appendix 4 Print Samples Interleaved 2 JAN13, EAN13EAN13+2 digits EAN13+5 digitsUPC-A+5 digits Industrial 2Customer bar code KIX CodeAppendix 5 Glossaries USB Universal Serial Bus Device used to remove labels from the backing paperMedia and ribbon Index Index EO1-33047E
Related manuals
Manual 45 pages 54.11 Kb

BSA4TMTS12QMR, B-SA4TM, B-SA4TM-TS12-QM-R specifications

The Toshiba B-SA4TM-TS12-QM-R is a versatile and high-performance thermal printer designed to meet the demanding needs of various industries, ranging from retail to logistics. Known for its reliability and efficiency, this printer is part of Toshiba's celebrated B-SA4 series that showcases robust engineering and advanced printing technologies.

One of the standout features of the B-SA4TM-TS12-QM-R is its exceptional print speed, capable of reaching up to 152 mm per second. This rapid output ensures that businesses can efficiently manage their printing tasks, reducing wait times and boosting productivity. Its 300 dpi resolution guarantees that printed images and text are sharp and clear, making it ideal for producing high-quality labels, barcodes, and receipts.

The printer is equipped with a user-friendly interface that simplifies operation and maintenance. The LCD screen provides real-time information about printing status and alerts, allowing users to monitor the printer's performance easily. Furthermore, its compact design makes it suitable for environments with limited space while still delivering a robust printing solution.

In terms of connectivity, the B-SA4TM-TS12-QM-R offers multiple options including USB, Ethernet, and serial ports, ensuring that it can easily integrate into existing systems. It also supports a range of operating systems, enhancing its versatility across different hardware environments.

Toshiba has integrated advanced technologies into the B-SA4TM series, such as an innovative ribbon-saving mechanism, which allows for longer print runs without frequent ribbon changes. This feature not only reduces operational costs but also minimizes waste, making it a more environmentally friendly choice.

Additionally, the printer supports a wide variety of media types and sizes, including labels, tags, and wristbands. Its ability to handle diverse materials makes it an excellent choice for businesses that have varied printing needs. The B-SA4TM is also designed for easy media loading, allowing users to change supplies quickly and efficiently.

Overall, the Toshiba B-SA4TM-TS12-QM-R combines speed, quality, and user-friendliness, making it a formidable addition to any business's printing lineup. With its advanced features and robust design, it stands out as a reliable solution for users looking for high-performance thermal printing. Whether it's for shipping, inventory management, or retail operations, the B-SA4TM series delivers exceptional performance that meets the needs of today’s fast-paced environments.
Top Page Image Contents