Toshiba BSA4TMTS12QMR, B-SA4TM-TS12-QM-R owner manual Ribbon

Page 111

7. SUPPLY SPECIFICATIONS

ENGLISH VERSION EO1-33047

7.2 Ribbon

(11) Print Position Accuracy

When using RFID tag embedded media, the print position accuracy may exceed the guaranteed tolerance of ±1 mm in all issue modes.

It is required to check the print position accuracy for each media type.

(12) Paper Jam Error

Depending on the type of glue or the flexibility of labels, a label may come unstuck in front of the sensor unit, which cause a paper jam. Particularly, the frequency of paper jam could become higher on the condition of low operating temperature or use of short-pitch labels.

It is required to check the media feed using the media to be used under the actual operating environment.

7.2 Ribbon

Please make sure that the ribbon being used is approved by TOSHIBA TEC. The warranty does not apply to any problem caused by using non-approved ribbons.

For information regarding TOSHIBA TEC approved ribbon, please contact a TOSHIBA TEC service representative.

Type

Spool type

Width

60 – 110 mm

 

Recommended width is 60, 90, and 110 mm.

Length

450 m (within ∅75 mm)

Outside Diameter

∅75 mm (max.)

The table below shows the correlation between ribbon width and media width (backing paper is not included.)

Ribbon width

 

Media width

60 mm

25

– 55 mm

90 mm

55

– 85 mm

110 mm

85

– 105 mm

NOTES:

1.To ensure print quality and print head life use only TOSHIBA TEC specified ribbons.

2.Too much difference in width between media and ribbon may cause ribbon wrinkles. To avoid ribbon wrinkles use a ribbon for proper media width shown in the above table. Do not use a ribbon that is narrower than media.

3.When discarding ribbons, please follow the local rule.

E7- 8

Image 111
Contents SA4TM Series Vorsicht CE Compliance for EU onlySA4TM Series Waste Recycling information for users For Safety Precautions for Handling of Wireless Communication DeviceMeanings of Each Symbol Safety SummaryRequest Regarding Maintenance PrecautionsTable of Contents EA4-1 EA1-1EA2-1 EA3-1Product Overview Introduction FeaturesAccessories Rear View DimensionsAppearance Front ViewInterior Operation PanelOption Name Type Usage OptionsReference Printer SetupSetup Flow ProcedureExample of US Type InstallationConnecting the Power Cord Attaching the Printer Rear SupportInsert the Media Shaft into the core of a media roll Loading the MediaTake out the Media Holder Ass’y from the printer Raise the Release Lever and remove the Media Holder LeftPlace the Media Holder Ass’y into the printer Fold the Release Lever to lock the Media Holder LeftClick Upper Sensor Upper SensorLever Ass’y Setting the Feed Gap Sensor position Setting the Black Mark Sensor position Strip mode Option Batch modePress down the Release Bar to open the Strip Unit Cut mode Option Label or Thin mediaTag paper or Thick paper Loading the Ribbon Open the Ribbon Cover Gently close the Top Cover until it clicks ContConnecting the Printer to Your Host Computer Turning the Printer How to enter the System Mode Sequentially Parameter SettingWhile 2PARAMETER SET is displayed on the LCD Message Time the Pause key is pressed, the sub menus are displayedAfter selecting a character code, press the Pause key Character Zero SelectionCharacter Code Selection Use the Feed or Restart key to select a desired optionAfter selecting a data length, press the Pause key Baud Rate SelectionAfter selecting a baud rate, press the Pause key Data Length SelectionStop Bit Length Selection Parity SelectionFlow Control Code Selection After selecting an auto forward wait, press the Pause key LCD Language SelectionAfter selecting a language, press the Pause key Auto Forward Wait SelectionControl Code Selection After selecting the Feed key function, press the Pause key Strip Wait Status SelectionAfter selecting the Strip Wait Status, press the Pause key Feed Key Function SelectionAfter selecting a Euro code, press the Pause key Kanji Code SelectionAfter selecting a Kanji code, press the Pause key Euro Code SelectionAfter selecting an ACK/BUSY timing, press the Pause key Auto Print Head Check SelectionAfter selecting auto print head check, press the Pause key Centronics Interface ACK/BUSY Timing SelectionWeb Printer Function Selection Input Prime SelectionAfter selecting the Input Prime, press the Pause key Expansion I/O Interface Type Selection Ribbon Near End SelectionLabel End/Ribbon Error Selection Plug & Play SelectionAfter selecting a Plug & Play, press the Pause key Pre-Strip Selection Maxi Code Specification Selection Reverse Feed Speed SelectionAfter selecting the Back Feed Speed, press the Pause key After selecting a strip motor torque, press the Pause key Keyboard Interface SelectionAfter selecting a keyboard interface, press the Pause key Strip Motor Torque SelectionAfter selecting a printing method, press the Pause key Dump Mode SettingAfter selecting the receive buffer, press the Pause key Use the Feed or Restart key to select a printing methodData in the receive buffer is printed as follows Receive Buffer SizeRequired Label Length When the Pause key is pressed, Basic program is executed While 6AUTO Calib is displayed on the LCD Message Display Press the Pause key to enter the Automatic Calibration ModeWhen 6AUTO Calib appears, press the Pause key Automatic CalibrationLAN Setting Time Setting Date SettingReal Time Clock Setting 3 Low Battery Check Setting RTC Data Renewal Timing SettingCont IP Address Setting TCP/IP Feed and Pause keys This parameter is to set a Gateway IP address Printer IP AddressThis parameter is to set an IP address Gateway IP AddressSubnet Mask This parameter is to set a Subnet MaskSocket Port This parameter is to set a Dhcp client ID This parameter is to enable DhcpDhcp Dhcp Client IDDhcp Host Name This parameter is to set a Dhcp host nameAscii code and Hex. code correspondence table General Description Installing the Printer DriversInstalling the Printer Driver IntroductionWindows 98/Me E2-47 Windows 2000/XP E2-49 USB Interface E2-51 E2-52 E2-53 Finish button E2-55 E2-56 E2-57 Uninstalling the Printer Driver Adding a LAN Port Windows 98/ME Adding/Deleting a LAN PortDeleting a LAN Port Others Printer Driver UpgradesUsing the Printer Driver Print Test AdjustmentWhen using an optional Cutter Module or Strip Module Position and Print Tone Fine Adjustment When setting +0.0 mm Position and PrintTone Fine Example of Cut Position Fine Adjustment Example of Strip Position Fine Adjustment Restart Feed When setting +50.0 mm When setting -50.0 mmPosition and Print Tone Fine Adjustment Ribbon Motor Voltage Fine Adjustment Press the Restart key Threshold SettingJam errors Manually setSensor Status Display Black Mark Sensor AdjustmentFeed Gap Sensor Adjustment Black Mark Sensor/Feed Gap Sensor Adjustment No media„ When using the Feed Gap Sensor „ When using the Black Mark Sensor„ Manual Threshold Setting „ Storing a No Media Level VoltagePress and hold the Restart or Feed key for about 3 seconds Black Mark Sensor Used to restart printing On Line OperationOperation Panel Used to stop printing temporarilyReset OperationPress and hold the Restart key for 3 seconds or longer Maintenance CleaningPrint Head/Platen/ Sensors Print Head/Platen/ Sensors Covers and Panels Optional Cutter Module 1. Open the Front Cover Same way, clean the outside of the Cutter BladeGuide Roller Strip Roller Backing Paper Feed Roller Troubleshooting Error MessagesRestart key Error Messages Problems/Cause Possible Problems Causes Solutions Possible ProblemsCutter blade is dirty Clean the cutter blade Removing Jammed MediaRibbon is not loaded properly Load the ribbon properly Printer Specifications This section describes the printer specificationsModel Mail 4STATE Customer CODE, RSS14 Label Supply SpecificationsMedia Media TypeDetection Area of the Transmissive Sensor LabelTag paper with square holes Effective Print Area Detection Area of the Reflective SensorExample 1 UPM Raflatac’s Rafsec Short Dipole 2 Tag Rfid Tag58mm±6mm 5mm Supply Specifications Ribbon Combination of Media and Ribbon Recommended Media and Ribbon TypesMedia type Description Ribbon type DescriptionCare/Handling of Media and Ribbon Appendix 1 Messages and Leds Symbols in the messageDhcp client is being initialized When the Dhcp function is enabledVoltage of the Real Time Clock Battery Base LAN Board is being initializedFollowing message appears Parallel interface Centronics Appendix 2 InterfacePIN ConnectorLED status Link LED Number of ports Power source Self power Connector Type BNumber of ports Connector RJ-45 StandardEncoding Tag → RW Serial interface OptionWireless LAN Option Expansion I/O Interface Option B-SA704-IO-QM-R Appendix 3 Power Cord When purchasing the power cordAt least, 125% of the rated current of the product Appendix 4 Print Samples Appendix 4 Print Samples EAN13+5 digits Interleaved 2JAN13, EAN13 EAN13+2 digitsKIX Code UPC-A+5 digitsIndustrial 2 Customer bar codeAppendix 5 Glossaries Device used to remove labels from the backing paper Media and ribbonUSB Universal Serial Bus Index Index EO1-33047E
Related manuals
Manual 45 pages 54.11 Kb

BSA4TMTS12QMR, B-SA4TM, B-SA4TM-TS12-QM-R specifications

The Toshiba B-SA4TM-TS12-QM-R is a versatile and high-performance thermal printer designed to meet the demanding needs of various industries, ranging from retail to logistics. Known for its reliability and efficiency, this printer is part of Toshiba's celebrated B-SA4 series that showcases robust engineering and advanced printing technologies.

One of the standout features of the B-SA4TM-TS12-QM-R is its exceptional print speed, capable of reaching up to 152 mm per second. This rapid output ensures that businesses can efficiently manage their printing tasks, reducing wait times and boosting productivity. Its 300 dpi resolution guarantees that printed images and text are sharp and clear, making it ideal for producing high-quality labels, barcodes, and receipts.

The printer is equipped with a user-friendly interface that simplifies operation and maintenance. The LCD screen provides real-time information about printing status and alerts, allowing users to monitor the printer's performance easily. Furthermore, its compact design makes it suitable for environments with limited space while still delivering a robust printing solution.

In terms of connectivity, the B-SA4TM-TS12-QM-R offers multiple options including USB, Ethernet, and serial ports, ensuring that it can easily integrate into existing systems. It also supports a range of operating systems, enhancing its versatility across different hardware environments.

Toshiba has integrated advanced technologies into the B-SA4TM series, such as an innovative ribbon-saving mechanism, which allows for longer print runs without frequent ribbon changes. This feature not only reduces operational costs but also minimizes waste, making it a more environmentally friendly choice.

Additionally, the printer supports a wide variety of media types and sizes, including labels, tags, and wristbands. Its ability to handle diverse materials makes it an excellent choice for businesses that have varied printing needs. The B-SA4TM is also designed for easy media loading, allowing users to change supplies quickly and efficiently.

Overall, the Toshiba B-SA4TM-TS12-QM-R combines speed, quality, and user-friendliness, making it a formidable addition to any business's printing lineup. With its advanced features and robust design, it stands out as a reliable solution for users looking for high-performance thermal printing. Whether it's for shipping, inventory management, or retail operations, the B-SA4TM series delivers exceptional performance that meets the needs of today’s fast-paced environments.