Siemens Electrical Lean Switch installation instructions Power Supply

Page 30

Ports and Displays

!Warning

Industrial Ethernet ELS TP40M switches are designed for operation with safety extra-low voltage. This means that only safety extra-low voltages (SELV) complying with IEC950/EN60950/ VDE0805 can be connected to the power supply terminals.

The power supply unit to supply the ELS TP40M must comply with NEC Class 2 (voltage range 18 - 32 V, current requirement 150 mA).

Never connect the ELS to a.c. power supplies or d.c. power supplies greater than 32 V d.c.

Power Supply

The power supply is connected over a high resistance with the enclosure to allow an ungrounded setup. The ELS TP40M device can also be grounded using the PE screw terminal on the terminal block.

30	Industrial Ethernet
	A5E00152007-03

Image 30

Contents Simatic NET Classification of Safety-Related Notices Qualified Personnel Safety Instructions Regarding your ProductTrademarks Correct Usage of Hardware ProductsPreface Purpose of the Installation InstructionsValidity of the Installation Instructions ConsignmentGuide to the Manual Further DocumentationFinding Information AudiencePersonnel Qualification Requirements Standards and ApprovalsContents Technical Specifications IndexIntroduction ELS TP40 Possible AttachmentsProperties of the ELS TP40 ELS TP40M ELS TP40MProperties of the ELS TP40M ELS TP80 Properties of the ELS TP80Functions Introduction Network Topologies Network Topologies with ELS TP40 ELS TP40 Bus TopologyNetwork Topologies with ELS TP40M ELS TP40M Bus TopologyNetwork Topologies with ELS TP80 ELS TP80 Star TopologyPorts and Displays Pinning Ports and Displays of the ELS TP40TP Ports AutonegotiationIndustrial Ethernet A5E00152007-03 Power Supply Power Supply Port status display green/yellow LEDs Power display green LEDDisplays Status MeaningPorts and Displays of the ELS TP40M Ports and Displays Power Supply Power Supply Power Display green and red LEDs Port Status Display During StartupPorts and Displays of the ELS TP80 Power Supply Status of the ports is signaled by eight LEDs Installation and Maintenance Consignment Unpacking, Checking the ConsignmentInstallation PreparationsInstalling the ELS on a DIN Standard Rail DIN Rail MountingRemoving from a Standard Rail Removing from the Standard RailInstallation on a Simatic S7-300 Standard Rail Installing an ELS TP40 on a Simatic S7-300 Standard RailGrounding Installation in a 19 CubicleWall Mounting CubicleConnecting the IE FC TP Cable to the ELS TP40 or ELS TP40M Wall MountingS7 Standard Rail 42 mm 12 mm Maintenance Diagnostics over Industrial Ethernet Introduction Primary Setup Tool PST ConfigurationAutomatic IP Address Assignment using Dhcp Factory Setting Installation of the Primary Setup ToolSelecting the Language Windows NT DLC Protocol Installation Select Start Settings Control PanelWindows 2000 DLC Protocol Installation Windows XP DLC Protocol InstallationUser Interface of the PST Changing the Network Adapter Configuration Changing the Language PackageConfiguring the ELS Progress Bar Browsing NetworkMAC Address Obtain IP address from Dhcp serverAssign IP parameters Subnet mask Router default gatewayIP address By selecting Module DownloadSelect Module Start INC Browser Direct Start Starting Web Based ManagementRequirements Web Based Management WBMGeneral Internet BrowserAccess using WBM How to Access WBM on the ELSUser Interface of the WBM Device status fieldMenu tree Management Menus Function ExplanationSystem Location Switch InformationSystem Contact System NameGet Current Values/Set New Values Default Gateway IP Address InformationGet Current Values Diagnostics over Industrial Ethernet Mail Configuration Mail AddressFrom Field Subject Smtp Server IP-AddressTrap Configuration Trap AddressConstruction of the Trap report LED-StatusPort Status Event Configuration 16 Event Configuration WindowStatistic Information 17 Statistic Information WindowDiagnostics Using Snmp ELS private MIBInternet Browser Settings BrowserJava Virtual Machine Plugin Microsoft Internet Explorer 5.5 or 19 Microsoft Internet Explorer 6.0 Advanced Internet Options 20 Microsoft Internet Explorer 6.0 Connections Window 21 Microsoft Internet Explorer 6.0 LAN Settings 22 Microsoft Internet Explorer Proxy Settings Netscape 6.1 or 23 Netscape 6.2 Advanced Preferences Window24 Netscape 6.2 Proxy Preferences Window Technical Specifications Electrical Data Technical Specifications of the ELS TP40Attachments Permitted Cable LengthsPermitted Ambient Conditions/EMC ApprovalsMtbf Technical Specifications of the ELS TP40M Aging Time Minutes Permitted Only horizontal installationConstruction Ventilation slits top/bottomTechnical Specifications of the ELS TP80 ELS TP80 device Further Support Who to ContactAutomation and Drives, Service & Support Service & SupportService & Support on the Internet Training for Simatic NET CertificationProduct name EMC DirectiveArea of Application Installation Guidelines Conformity CertificatesAutonegotiation GlossaryIndex AutosensingAmbient conditions, permitted.... , 84 References Http//www4.ad.siemens.de/view/cs/de/8677203