Siemens Electrical Lean Switch installation instructions Installation, Preparations

Page 37

Installation and Maintenance

5.2Installation

There are several ways of installing the ELS:

●Installation on a 35 mm standard rail

●Installation on a SIMATIC S7-300 rail

●Installation in a 19" cabinet (along with other ELS modules in the 19" mounting system)

●Wall mounted

Note

•Remember that the ELS must only be installed horizontally (ventilation slits top/bottom see Figure 4). To ensure adequate convection, there must be a clearance of at least 5 cm above and below the ventilation slits. You should also make sure that the permitted ambient temperature range is not exceeded.

•During installation and operation, make sure that you adhere to the installation instructions and safety-related notices in this description and in the SIMATIC NET Industrial Ethernet Twisted Pair and Fiber-Optic Networks manual /2/.

•Unless specifically stated, the following installation options apply to all ELS switches.

Preparations

Remove the terminal block from the ELS and wire up the power supply lines as described in Section 4.1.2.

Industrial Ethernet	37
A5E00152007-03

Image 37

Contents Simatic NET Classification of Safety-Related Notices Trademarks Safety Instructions Regarding your ProductQualified Personnel Correct Usage of Hardware ProductsValidity of the Installation Instructions Purpose of the Installation InstructionsPreface ConsignmentFinding Information Further DocumentationGuide to the Manual AudienceStandards and Approvals Personnel Qualification RequirementsContents Index Technical SpecificationsIntroduction Possible Attachments ELS TP40Properties of the ELS TP40 ELS TP40M ELS TP40MProperties of the ELS TP40M Properties of the ELS TP80 ELS TP80Functions Introduction Network Topologies ELS TP40 Bus Topology Network Topologies with ELS TP40ELS TP40M Bus Topology Network Topologies with ELS TP40MELS TP80 Star Topology Network Topologies with ELS TP80Ports and Displays TP Ports Ports and Displays of the ELS TP40Pinning AutonegotiationIndustrial Ethernet A5E00152007-03 Power Supply Power Supply Displays Power display green LEDPort status display green/yellow LEDs Status MeaningPorts and Displays of the ELS TP40M Ports and Displays Power Supply Power Supply Port Status Display During Startup Power Display green and red LEDsPorts and Displays of the ELS TP80 Power Supply Status of the ports is signaled by eight LEDs Installation and Maintenance Unpacking, Checking the Consignment ConsignmentPreparations InstallationDIN Rail Mounting Installing the ELS on a DIN Standard RailRemoving from the Standard Rail Removing from a Standard RailInstalling an ELS TP40 on a Simatic S7-300 Standard Rail Installation on a Simatic S7-300 Standard RailWall Mounting Installation in a 19 CubicleGrounding CubicleWall Mounting Connecting the IE FC TP Cable to the ELS TP40 or ELS TP40MS7 Standard Rail 42 mm 12 mm Maintenance Diagnostics over Industrial Ethernet Introduction Automatic IP Address Assignment using Dhcp Factory Setting ConfigurationPrimary Setup Tool PST Installation of the Primary Setup ToolSelecting the Language Select Start Settings Control Panel Windows NT DLC Protocol InstallationWindows XP DLC Protocol Installation Windows 2000 DLC Protocol InstallationUser Interface of the PST Changing the Language Package Changing the Network Adapter ConfigurationProgress Bar Browsing Network Configuring the ELSObtain IP address from Dhcp server MAC AddressAssign IP parameters IP address Router default gatewaySubnet mask By selecting Module DownloadDirect Start Starting Web Based Management Select Module Start INC BrowserGeneral Web Based Management WBMRequirements Internet BrowserHow to Access WBM on the ELS Access using WBMDevice status field User Interface of the WBMMenu tree Function Explanation Management MenusSystem Contact Switch InformationSystem Location System NameGet Current Values/Set New Values IP Address Information Default GatewayGet Current Values Diagnostics over Industrial Ethernet Mail Address Mail ConfigurationFrom Field Smtp Server IP-Address SubjectTrap Address Trap ConfigurationLED-Status Construction of the Trap reportPort Status 16 Event Configuration Window Event Configuration17 Statistic Information Window Statistic InformationELS private MIB Diagnostics Using SnmpBrowser Internet Browser SettingsJava Virtual Machine Plugin Microsoft Internet Explorer 5.5 or 19 Microsoft Internet Explorer 6.0 Advanced Internet Options 20 Microsoft Internet Explorer 6.0 Connections Window 21 Microsoft Internet Explorer 6.0 LAN Settings 22 Microsoft Internet Explorer Proxy Settings 23 Netscape 6.2 Advanced Preferences Window Netscape 6.1 or24 Netscape 6.2 Proxy Preferences Window Technical Specifications Attachments Technical Specifications of the ELS TP40Electrical Data Permitted Cable LengthsApprovals Permitted Ambient Conditions/EMCMtbf Technical Specifications of the ELS TP40M Aging Time Minutes Construction Only horizontal installationPermitted Ventilation slits top/bottomTechnical Specifications of the ELS TP80 ELS TP80 device Who to Contact Further SupportService & Support Automation and Drives, Service & SupportService & Support on the Internet Certification Training for Simatic NETEMC Directive Product nameArea of Application Conformity Certificates Installation GuidelinesIndex GlossaryAutonegotiation AutosensingAmbient conditions, permitted.... , 84 Http//www4.ad.siemens.de/view/cs/de/8677203 References