Toshiba 120/150 manual Troubleshooting, Problem Possible cause Solution

Page 45

Troubleshooting

If any problem occurs, check the list below before contacting your authorised service representative.

Problem

Possible cause

Solution

Page

 

Unit plugged in?

Plug the unit into a grounded outlet.

3-3

 

 

 

 

 

 

Unit does not

Power switch on?

Turn the power switch on.

3-3

 

operate.

 

 

 

 

Side cover closed securely?

Gently close the side cover.

5-4

 

 

 

 

 

 

 

 

 

Front cover closed?

Gently close the front cover and then

5-4

 

 

 

close the side cover.

 

 

 

 

 

 

 

Blank copies

Is the original placed face

Place the original face down on the

3-5

 

 

down on the original table?

original table.

 

 

 

 

 

 

 

 

Is original image too dark or

Adjust the exposure manually.

3-6

 

 

too light?

 

 

 

 

 

 

 

 

Copies are

Is the unit in the automatic

Adjust the automatic exposure level.

3-7

 

too dark or

exposure mode?

 

 

 

too light.

 

 

 

 

Is the unit in the photo

Cancel the photo exposure mode.

3-6

 

 

 

 

exposure mode?

 

 

 

 

 

 

 

 

Dust, dirt, smud-

Original table or original cover

Clean regularly.

5-5

 

ges appear on

dirty?

 

 

 

 

 

 

 

 

copies.

Original smudged or blotchy?

Use a clean original.

--

 

Striped copies

Is transfer charger clean?

Clean the transfer charger.

5-6

 

 

Non-standard paper used?

Use standard paper. If using special

2-2

 

 

 

papers, feed the paper through the

 

 

 

 

single bypass.

 

 

 

Paper curled or damp?

Store paper flat in the wrapper in a dry

--

 

 

 

location.

 

 

 

 

 

 

 

Paper misfeeds

Pieces of paper inside unit?

Remove all pieces of misfed paper.

6-4

 

frequently.

 

 

 

 

Paper guides in the paper tray

Set the guides properly depending on

2-4

 

 

 

 

not set properly?

the paper size.

 

 

 

 

 

 

 

 

Too much paper in the paper

Remove excessive paper from the tray.

2-4

 

 

tray?

 

 

 

 

 

 

 

 

 

Is the paper too heavy?

Use paper within the specified range.

2-2

 

 

 

 

 

 

Images rub off

Paper damp?

Replace with dry paper. If the unit is not

7

 

the copy easily.

 

used for long time, remove the paper

 

 

 

 

from the paper tray and store it in its

 

 

 

 

wrapper in a dry location.

 

 

 

 

 

 

 

6-2TROUBLESHOOTING

Image 45
Contents Networking Documents %## FCC regulations Ozone information User safetyMachine noise information For user in the CanadaVaroitus Page Do not install your unit in areas that are Important points when selecting an installation siteTrademark acknowledgements Proper storage for suppliesDo not touch the photoconductive drum green portion Store paper in the wrapper and lying flatContents Appendix Page Introduction This chapter provides basic information for using the unitConventions used in this manual Using the ManualPhotoconductive drum Toner cartridge Part NamesOperation Panel Loading Paper Paper Type of paper feeding Type of media Size WeightTransparency FilmProper storage Loading the Paper Tray Gently push the paper tray back into the unit Open the bypass tray and extend the tray Bypass Feed including special paperPrint face 8LOADING Paper Making Copies Copy Flow Power on Connecting the Power CordInitial settings of operation panel Power off methodsAbout the scan head Setting a large original Original PlacementExposure ADJUSTMENT/PHOTO Copying Exposure adjustmentSET the Copy Quantity Automatic exposure adjustment REDUCTION/ENLARGEMENT/ZOOM To select a preset copy ratioTo select a zoom ratio RatioPress the tray select Key Selecting the Tray10MAKING Copies Special Functions Description of Special Functions Toner Save ModeUser Programs Program Mode Parameters Displaying Total Number of CopiesCopies will appear in two steps, each with three digits Maintenance Toner Cartridge Replacement Or 5 times Shutter Toner seal 4MAINTENANCE Cleaning the Unit CabinetOriginal table and the back side of the original cover Transfer charger Troubleshooting the Unit Problem Possible cause Solution TroubleshootingBe sure to use only genuine Toshiba parts and supplies Status IndicatorsMisfeed Removal Misfeed in the fusing area Lower the fusing unit release leverMisfeed in the paper feed area Misfeed in the transport area Start indicator will light upMaintenance Required Will go out and the start indicator will light upDeveloper Required 8TROUBLESHOOTING Installing the Software MFP driver Software for the Toshiba Personal MFP SeriesDesktop Document Manager Button ManagerHardware and Software Requirements Before InstallationOperatingsystem Interface Reference pages for how to install Flow of installationInstalling the Software Installing onto Windows XP USB/parallel interfaceDouble-click the setup icon Install the Software Page 12Begin installation of the printer driver Begin installation of the scanner driverInstalling onto Windows 98/Me/2000 USB interface Copying files for MFP driver installation 10Connect the USB interface cable. See p Windows 95/NT Windows 98/Me/2000 Page Page Start indicator Indicators on the Operation PanelPower save indicator Online indicatorHow to print Using the Printer ModeOpening the printer driver from the start menu Click the start buttonAbout interrupt copying Configuring the OptionUsing the Button Manager Using the Scanner ModeSetting up the Button Manager Windows XPWindows 98/Me/2000 Flow of the Button Manager setting Scan Parameter Setting Dialog BoxScanner e Event Press the Scanner key Using the Scanner key to begin scanningOpening the scanner driver and scanning from your computer Using the Toshiba TwainPress the start key Place the original you wish to scan on the original tableScan is started Scanning with the Scanner and Camera Wizard in Windows XP Select a name, format, and folder for the scanned imageClick Finish in the screen that appears Contents of the online manual HOW to USE the Online ManualClick theto read the online manual Using Other Installed Drivers Connecting the USB interface cable Connecting the Interface CableInterface cable Parallel interface cableConnecting the parallel interface cable Appendix Model STUDIO120 DP-1210 STUDIO150 DP-1510 SpecificationsSheet paper feed unit MY-1019 SoftwareOptional Equipment System configurationAuto document feeder MR-2014 Part namesSpecifications Using the ADFMisfeed in the ADF Stream feeding modeSide cover Tray Part names Loading copy paperMisfeed removal Index Alarm indicator Developer replacement requiredScanning with the Scanner Software License Disclaimer of Warranty on Software Toshiba Tec Germany Imaging Systems GmbH