Toshiba B-EX operation manual ANY Ssid on / Priority AP on / Other AP OFF

Page 52

[802.11b] Group [Channel]:

Set a channel for IEEE 802.11b.

The printer corrects channels that cannot be used due to country code settings.

Default

1

Range

1 to 14

[Baud Rate]:

Select the maximum transmission rate for IEEE 802.11b.

The transmission rate is adjusted to a value enabling communication by the communicating device.

Default

11

Mbps

Options

11

Mbps, 5.5 Mbps, 2 Mbps, 1 Mbps

[802.11g] Group [Channel]:

Set a channel for IEEE 802.11g.

The printer corrects channels that cannot be used due to country code settings.

Default

1

Range

1 to 13

[Baud Rate]:

Select the maximum transmission rate for IEEE 802.11g.

The transmission rate is adjusted to a value enabling communication by the communicating device.

Default

11

Mbps

Options

54

Mbps, 48 Mbps, 36 Mbps, 24 Mbps, 18 Mbps, 12 Mbps, 9 Mbps, 6 Mbps,

11

Mbps, 5.5 Mbps, 2 Mbps, 1 Mbps

 

[Priority AP] Group

[Property]:

Select ANY SSID/priority AP.

Default

11 Mbps

Options

ANY SSID OFF, ANY SSID ON / Priority AP OFF,

ANY SSID ON / Priority AP ON / Other AP OFF,

 

ANY SSID ON / Priority AP ON / Other AP ON

[MAC Address 1] [MAC Address 2] [MAC Address 3] [MAC Address 4] [MAC Address 5]: Set MAC addresses for access points that you want to connect preferentially.

The numbers indicate order of priority.

Connection to the MAC addresses is made in the order of descending priorities. Use 12 characters from "0" to "F" to enter addresses.

Entries are not case-sensitive.

When no address is entered, you can disable the current settings.

[Authentication] Group

[(1) Connection Mode]:

Select the connection mode.

Default

Infrastructure

Options

Adhoc, Infrastructure

[(2) Encryption]:

Select the encryption scheme.

Displayed options depend on the [(1) Connection Mode] settings.

Default

Disable

Options

Disable, WEP40, WEP104, TKIP, AES

[(3) Network Authentication]:

Select the network authentication system.

Displayed options depend on the [(1) Connection Mode] and [(2) Encryption] settings.

Default

Open System

Options

Open System, Shared Key, WPA-EAP, WPA-PSK, WPA2-EAP, WPA2-PSK

49

Image 52
Contents EX Series Table of Contents Appendix Features IntroductionSupported Printers Software License AgreementOutline of the Functions NotationScreens Used in This Document Trademark and CopyrightOperational Conditions DisclaimerSoftware Operation System HardwareInstallation Installation Procedure Page Uninstallation Start-up Printer Preparation Main Screen Page Menus FilePage Edit View Help Printer Setting EX6T2-T JP, QM, CNUSB LAN Multi LAN Page COM Page Environment Page Password Change Processing Screen Progress Bar ScreenCompletion Screen Progress Status Page Printer List Screen Functions Parameter Setting Page Page General Tab Type Type Mode General 2 Tab Auto Shell Page Device Tab QQ READY/BUSY XON+READY AUTO, XON/XOFF AUTO, READY/BUSY RTS, XON+XOFFREADY/BUSY ACK/BUSYLAN Tab HEX SnmpHEX, Ascii Wins Wlan Tab ANY Ssid on / Priority AP on / Other AP OFF WEP40 EAP-MD5 EAP-TLS EAP-TTLS LeapPeap EAP-FASTHEX Wlan 2 Tab MSCHAPV2 MSCHAPV2, GTCPage Rfid Tab NoneAuto Maintenance Self Diagnosis TabCENTRO, LAN/WLAN, RFID, RTC JA, QM, CN Page Memory Management Tab Page Page Download Firmware DownloadPage Basic Download Page Page Create HTML/XML ROM Page Tool Tool TabCreate External Character Tab Page X 0.5, 1.0 x 1.0, 2.0 x 2.0, 3.0 x 3.0, 1.0 x 2.0, 2.0 x Page Test Print Tab Page Slant Lines 1 dot Characters Slant Lines 3 dot Barcodes Appendix Error Message List Page Page Setup Items List Setup group Setup item Options or range DefaultECO XML Auto XON+READY Auto XON+XOFF Auto READY/BUSY READY/BUSY RTS LPR ESS ID WEP MSCHAPV2 GTC None