NETGEAR WPNT834 manual Configuring LAN TCP/IP Setup Parameters

Page 93

Reference Manual for the RangeMax 240 Wireless Router WPNT834

Configuring LAN TCP/IP Setup Parameters

The router is shipped preconfigured to use private IP addresses on the LAN side, and to act.as a DHCP server. The router’s default LAN IP configuration is:

LAN IP address—192.168.1.1

Subnet mask—255.255.255.0

These addresses are part of the IETF-designated private address range for use in private networks, and should be suitable for most applications. If your network has a requirement to use a different IP addressing scheme, you can make those changes in this menu.

The LAN IP parameters are:

IP Address

This is the LAN IP address of the router.

IP Subnet Mask

This is the LAN Subnet Mask of the router. Combined with the IP address, the IP Subnet Mask allows a device to know which other addresses are local to it, and which must be reached through a gateway or router.

RIP Direction

RIP (Router Information Protocol) allows a router to exchange routing information with other routers. The RIP Direction selection controls how the router sends and receives RIP packets. Both is the default.

When set to Both or Out Only, the router broadcasts its routing table periodically.

When set to Both or In Only, the router incorporates the RIP information that it receives.

When set to None, the router does not send any RIP packets and ignores any RIP packets received.

RIP Version

This controls the format and the broadcasting method of the RIP packets that the router sends. (It recognizes both formats when receiving.) By default, this is set for RIP-1.

RIP-1 is universally supported. RIP-1 is probably adequate for most networks, unless you have an unusual network setup.

RIP-2 carries more information. RIP-2B uses subnet broadcasting.

Note: If you change the LAN IP address of the router while connected through the browser, you will be disconnected. You must then open a new connection to the

new IP address and log in again.

8-14

Advanced Configuration of the Router

v1.0, November 2005

Image 93
Contents NETGEAR, Inc Statement of Conditions TrademarksEN 55 022 Declaration of Conformance Bestätigung des Herstellers/ImporteursVoluntary Control Council for Interference Vcci Statement Certificate of the Manufacturer/ImporterCustomer Support World Wide WebV1.0, November Contents Chapter Wireless Configuration Chapter Troubleshooting Viii Chapter About This Manual Audience, Scope, Conventions, and FormatsTypographical Conventions How to Use This Manual How to Print this ManualManual Scope Printing the Full Manual V1.0, November Chapter Introduction Key FeaturesRangeMax Multi-In, Multi-Out Mimo Technology 802.11g Wireless NetworkingSecurity Powerful, True Firewall with Content FilteringExtensive Protocol Support Autosensing Ethernet Connections with Auto UplinkMaintenance and Support Easy Installation and ManagementNetgear Related Products Package ContentsStatus Light Descriptions Router’s Front PanelRouter’s Rear Panel Road Map for How to Get There From Here Road Map for ‘How to Get There From Here’Connection Printers in a A Road Map for How to Get There From HereV1.0, November Prepare to Install Your Wireless Router Chapter Connecting the Router to the InternetFirst, Use the Smart Wizard to Configure the Wireless Router Now, Set Up a Computer for Wireless Connectivity Troubleshooting Tips Ways to access the router Overview of How to Access the Wireless RouterV1.0, November V1.0, November How to Bypass the Configuration Assistant ISP Does Not Require Login How to Manually Configure Your Internet ConnectionV1.0, November V1.0, November Using the Smart Setup Wizard Netgear Product Registration, Support, and Documentation V1.0, November Observing Performance, Placement, and Range Guidelines Chapter Wireless ConfigurationImplementing Appropriate Wireless Security Understanding Wireless Settings V1.0, November WEP Basic Wireless Security OptionsV1.0, November If WPA-PSK or WPA2-PSK Authentication is Used How to Set Up and Test Basic Wireless Connectivity Default Factory SettingsV1.0, November How to Configure WEP V1.0, November How to Configure WPA-PSK or WPA2-PSK Wireless Security Click the Turn Access Control On check box How to Restrict Wireless Access by MAC AddressV1.0, November V1.0, November Content Filtering Overview Chapter Content FilteringBlocking Access to Internet Sites Blocking Access to Internet Services Configuring a User Defined Service Blocking Services by IP Address Range Scheduling When Blocking Will Be EnforcedLog entry descriptions Viewing Logs of Web Access or Attempted Web AccessLog action buttons Configuring E-Mail Alert and Web Access Log NotificationsV1.0, November Viewing Wireless Router Status Information Chapter MaintenanceThis screen shows the following parameters Wireless Router Status FieldsConnection Status Items Wireless port of the router. The default is Netgear RegionRouter Statistics Items Viewing a List of Attached Devices Configuration File ManagementErasing the Configuration Backing Up and Restoring the ConfigurationUpgrading the Router Software V1.0, November Changing the Administrator Password V1.0, November Chapter Troubleshooting Power Light Not OnBasic Functioning LAN or WAN Port Lights Not On Lights Never Turn OffTroubleshooting the Web Configuration Interface Troubleshooting the ISP Connection Testing the LAN Path to Your Router Troubleshooting a TCP/IP Network Using a Ping UtilityTesting the Path from Your Computer to a Remote Device Restoring the Default Configuration and Password Problems with Date and Time Configuring Advanced Wireless Settings Advanced Configuration of the RouterV1.0, November Wireless Card Access List Wireless Card Access Setup Configuring Port Triggering and Port Forwarding V1.0, November Click Add Service Configuring Port Forwarding to Local Servers Click the Add Custom Service button Adding a Custom ServiceEditing or Deleting a Port Forwarding Entry Local Web and FTP Server ExampleMultiple Computers for Internet Gaming Connecting Automatically, as Required Configuring the WAN Setup OptionsSetting Up a Default DMZ Server Disabling the SPI FirewallResponding to a Ping on the Internet WAN Port Setting the MTU Size Using the LAN IP Setup OptionsConfiguring LAN TCP/IP Setup Parameters Using Address Reservation Using the Router as a Dhcp serverUsing a Dynamic DNS Service Select the Use a Dynamic DNS Service check box Configuring Static Routes V1.0, November Select the Turn Remote Management On check box Enabling Remote Management AccessV1.0, November Using Universal Plug and Play UPnP V1.0, November V1.0, November Power Adapter Appendix a Technical SpecificationsPSK Document Link Appendix B Related DocumentsV1.0, November
Related manuals
Manual 6 pages 35.94 Kb