NETGEAR WGE101 manual Connecting the Bridge to Multiple Devices

Page 7

WGE101 54 Mbps

Gaming console or other

Wireless Ethernet Bridge

Ethernet-enabled device

4.Turn off the gaming console or other Ethernet-enabled device.

5.Connect the provided Ethernet cable between the WGE101 Wireless Bridge and the gaming console or other Ethernet-enabled device.

6.Connect the power adapter to the bridge and plug the power adapter in to a power outlet.

The Power and Wireless LAN lights should light up.

7.After you see the Wireless LAN light light up, turn on the gaming console or other Ethernet-enabled device.

If the bridge and the Ethernet-enabled device are successfully connected, the Network

light will light up. This light flashes when there is network activity.

Note: If your setup works with the default settings, you don’t need to configure the bridge unless you need to change the Country/Region setting from the default setting (United States) or you need to assign a unique IP address to subsequent WGE101 bridges. See page 12 for information on configuring the bridge.

Connecting the Bridge to Multiple Devices

1.Unpack the box and verify the contents.

2.Identify a flat surface where you will put the wireless bridge. For best results, follow these guidelines:

•Place it away from potential sources of interference, such as computers, monitors, TVs, microwaves, cordless phones, or large metal surfaces.

Warning: Failure to follow these guidelines can cause intermittent or complete failure of wireless connectivity.

•Place it in an elevated location such as a high shelf or on a wall in the center of your wireless access area. If you mount the bridge on a wall, do not place the bridge

in such a way that it is vertical with the NETGEAR name upside-down and the power adapter plug hanging from the bottom of the unit. Having the unit in this position violates power adapter regulations.

3.Lift the bridge’s antenna so it is vertical.

4. Turn off the gaming consoles or other Ethernet-enabled devices.

5

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Page Table of Contents Package Contents Preparing to Install the WGE101 BridgeIntroduction System Requirements Placement and Range GuidelinesOperating Modes IP address WGE101 Default Wireless Configuration SettingsConnecting the Bridge to a Single Device Installing the WGE101 BridgeConnecting the Bridge to Multiple Devices WGR614 54 Mpbs Wireless Router WGE101 54 Mbps Identifying Your Wireless Network Settings Preparing To Configure the WGE101 BridgeChecking and Changing the Computer’s IP Address Connecting the Bridge to a ComputerPage Mac OS Choose System Preferences from the Apple  menu Changing the Bridge’s IP AddressLinux and Unix Click Apply Click Logout Using the NetBIOS NameChanging the Country/Region Setting Configuring the WGE101 Bridge for Your Wireless NetworkClick Wireless Settings Changing the Bridge’s Password Selecting a Specific Wireless NetworkWireless Settings Click Change PasswordEnabling WEP Security Upgrading the Bridge Configuring the Bridge for Ad-Hoc Mode Setting the Bridge’s Data Rate Restoring the Bridge to the Default Settings WGE101 Bridge Status Lights and SettingsStatus Lights Status Information Symptom Cause Solution Troubleshooting TipsSymptom Solution Cause System Requirements for the Bridge WGE101 System Requirements and SpecificationsBridge Specifications Environmental SpecificationsStatement of Conditions Support Information Technical Support

WGE101 specifications

The NETGEAR WGE101 is a pioneering wireless gaming adapter that enables online gaming on consoles without the need for a wired connection. Designed primarily to support gaming consoles like the PlayStation 2, Xbox, and other Ethernet-enabled devices, this adapter bridges the gap between traditional gaming setups and modern wireless networking technologies. With its compact design and user-friendly setup, the WGE101 has become a popular choice among gamers seeking to enhance their gaming experience.

One of the key features of the NETGEAR WGE101 is its wireless compatibility. It operates on the IEEE 802.11b standard, providing a wireless connection with a maximum throughput of up to 11 Mbps. While this may seem modest by today’s standards, it was quite effective during the adapter's peak usage and sufficient for many online gaming applications. The WGE101 supports a range of wireless security protocols including WEP and WPA, ensuring a secure connection for users.

The setup process of the WGE101 is notably straightforward. It features a plug-and-play design, allowing users to connect it directly to their gaming console via an Ethernet cable. The built-in configuration utility simplifies the connection to the home Wi-Fi network, making it accessible even for those who may not be tech-savvy. Additionally, the WGE101’s compact size allows it to be conveniently placed near a gaming console without taking up much space.

The NETGEAR WGE101 also boasts advanced features such as QoS (Quality of Service) capabilities that prioritize gaming traffic over other types of data. This ensures that online gaming sessions can proceed smoothly without significant lag, even when other devices are using the network. Moreover, its ability to work seamlessly with a variety of routers enhances flexibility for users.

Furthermore, the WGE101 includes an LED indicator that provides real-time feedback on connection status, helping users troubleshoot potential connectivity issues. This added convenience is critical for gamers who desire uninterrupted gameplay.

In conclusion, the NETGEAR WGE101 wireless gaming adapter remains a noteworthy option for gamers looking to connect their consoles to the internet wirelessly. With its reliable performance, easy setup, and essential features tailored for gaming, the WGE101 has made a lasting impact in the realm of online gaming connectivity.
Top Page Image Contents