NETGEAR WAG302 manual Default Factory Settings, Time Zone Adjust for Daylight Saving TIme Disabled

Page 25

Reference Manual for the NETGEAR ProSafe Dual Band Wireless Access Point WAG302

Default Factory Settings

When you first receive your WAG302, the default factory settings will be set as shown below. You can restore these defaults with the Factory Default Restore switch on the rear panel — see “WAG302 front panel” on page 2-6.

FEATURE

FACTORY DEFAULT SETTINGS

 

 

User Name (case sensitive)

admin

 

 

Password (case sensitive)

password

 

 

Operating Mode

Access Point

 

 

Access Point Name

netgearxxxxxx where xxxxxx are the last six

 

digits of the wireless access point's MAC address

Built-in DHCP client

DHCP client disabled

Built-in DHCP server

DHCP server disabled

IP Configuration

IP Address: 192.168.0.230

(if DHCP server is unavailable)

Subnet Mask: 255.255.255.0

 

Gateway: 0.0.0.0

11a Network Name (SSID)

NETGEAR_11a

 

 

11g Network Name (SSID)

NETGEAR_11g

 

 

Broadcast Network Name (SSID

Enabled

 

 

802.11a Radio Frequency Channel

52

 

 

802.11g Radio Frequency Channel

11

 

 

AutoCell RF Management

Enabled

AutoCell Enhanced RF Security ‘stealth’ mode

Disabled

WEP/WPA

Disabled

 

 

Restricting connectivity based on MAC Access

Disabled

Control List

 

Spanning Tree Protocol

Enabled

 

 

Time Zone

GMT

 

 

Time Zone Adjust for Daylight Saving TIme

Disabled

 

 

SNMP

Enabled but Trap forwarding is disabled

 

 

Secure Telnet

Enabled

 

 

Basic Installation and Configuration

3-3

202-10078-01

Image 25
Contents NETGEAR, Inc Technical Support Tested to Comply with FCC Standards WAG302 ProSafe Dual Band Wireless Access PointDeclaration of Conformity Industry Canada Compliance Statement Product and Publication Details Contents Chapter Management Appendix a Specifications Appendix C Command Line Reference Audience, Scope, Conventions, and Formats Chapter About This ManualBold How to Use This Manual Printing a Page in the Html View How to Print this ManualAbout This Manual Chapter Introduction About the WAG302 ProSafe Dual Band Wireless Access PointSupported Standards and Conventions Key FeaturesAutoCell-The Self-Organizing Wireless Network Compatible and Related Netgear Products 802.11a/g Standards-based Wireless NetworkingAutosensing Ethernet Connections with Auto Uplink What’s In the Box? System RequirementsFront Panel Hardware Description100 802.11a Wlan Rear Panel802.11g Wlan Serial Console Port Observing Placement and Range Guidelines Chapter Basic Installation and ConfigurationCabling Requirements Time Zone Adjust for Daylight Saving TIme Disabled Default Factory SettingsEnabled but Trap forwarding is disabled Secure Telnet EnabledLUHOHVVDWD 6HFXULW\2SWLRQV Understanding WAG302 Wireless Security OptionsSET UP the WAG302 Access Point Installing the WAG302 Access PointLogin window Web browser will then display the WAG302 General information Basic Settings menu Basic Installation and Configuration Wireless Settings 11a menu Deploy the WAG302 Access Point How to Log In to the WAG302 Using Its Default IP Address Wireless Settings 11a Understanding Basic Wireless SettingsBasic Installation and Configuration Wireless Settings 11b/g Basic Installation and Configuration Basic Installation and Configuration Understanding WEP/WPA Security Options 10 WEP/WPA Settings menus for 11a and 11b/gBasic Installation and Configuration 802.11a Configuration Before You Change the Ssid and WEP Settings802.11b/g Configuration How to Set Up and Test Basic Wireless Connectivity Access Control 11a menu Access Control 11b/g menu How to Restrict Wireless Access by MAC AddressHow to Configure WEP Click Apply to save your settings How to Configure WPA with Radius 13 Radius Server Settings menu 14 WEP/WPA Settings menus for 11a and 11bg 15 WEP/WPA Settings menus for 11a and 11bg How to Configure WPA-PSKIP Address Using the Basic IP Settings OptionsSpanning Tree Protocol Basic Installation and Configuration Remote Management Chapter ManagementHow to Use the CLI via the Console Port Using the Secure Telnet InterfaceSecure Telnet Client CLI CommandsSyslog and Activity Log information Using Syslog and Activity Log InformationGeneral Information Viewing General and Statistical InformationCurrent IP Settings Field Description Access Point InformationCurrent Wireless Settings 11a Field Description Current Wireless Settings 11b/g Wireless 11a Received/Transmitted Field Description Wired Ethernet Received/TransmittedStatistics Viewing a List of Attached Devices Field Description Wireless 11b/g Received/TransmittedRefresh button Configuration File Management Upgrading the Wireless Access Point SoftwareRestoring the WAG302 to the Factory Default Settings Saving and Retrieving the ConfigurationRebooting the Access Point Using the Reset Button to Restore Factory Default SettingsSet Password menu Changing the Administrator PasswordManagement Understanding Advanced IP Settings for Wireless Clients Chapter Advanced ConfigurationAdvanced IP Settings for Wireless Clients screen Understanding Advanced Wireless Settings Enhance RF Privacy -- Default Disable Problem AutoCell SettingsAuto RF Management -- Default Enable AutoCell RF ManagementAuto RF Management Enhanced RF Security ‘Stealth Mode’ Additional AutoCell View Management Options Advanced Wireless Settings screen Configuring Wireless LAN ParametersEnabling Wireless Bridging and Repeating Point-to-Point Bridge How to Configure a WAG302 as a Point-to-Point BridgeManual Advanced Configuration Multi-Point bridging How to Configure Wireless RepeatingAdvanced Configuration No lights are lit on the access point Chapter TroubleshootingLAN light is not lit Wireless LAN activity light does not light upWhen I enter a URL or IP address I get a timeout error Cannot connect to the WAG302 to configure itUsing the Reset Button to Restore Factory Default Settings Specifications for the WAG302 Appendix a SpecificationsParameter WAG302 ProSafe Dual Band Wireless Access Point Specifications Wireless Networking Overview Appendix B Wireless Networking BasicsInfrastructure Mode Network Name Extended Service Set Identification Essid Ad Hoc Mode Peer-to-Peer WorkgroupAuthentication Authentication and WEP Data Encryption802.11b Authentication Open System Steps 802.11b Authentication Shared Key Steps Key Size WEP Configuration Options Wireless Channels802.11b/g Wireless Channels Channel Center Frequency Frequency Spread Table B-2 802.11b/g Radio Frequency ChannelsChannel Frequency 802.11a Wireless ChannelsWAG302 user can use five channels in turbo mode WPA Wireless SecurityHow Does WPA Compare to WEP? How Does WPA Compare to Ieee 802.11i? What are the Key Features of WPA Security?Wireless Networking Basics Radius Server Figure B-3 WPA OverviewAccess point replies with an EAP-request identity message WPA Data Encryption Key Management Temporal Key Integrity Protocol Tkip Product Support for WPA Is WPA Perfect?Changes to Wireless Access Points Changes to Wireless Client Programs Command Sets Appendix C Command Line ReferenceCommand Line Reference Command Line Reference Command Line Reference 802.1x 100BASE-Tx802.11a 802.11bCat Auto UplinkCertificate Authority Domain Name Dynamic Host Configuration ProtocolLocal area network Internet ProtocolMAC address MbpsNetmask NetBIOSNetwork Address Translation PacketWide area network Wi-Fi Windows Internet Naming ServiceWireless Network Name Ssid Glossary
Related manuals
Manual 2 pages 4.37 Kb