Aruba Networks Comprehensive Overview of Aruba AP 60 Connectivity and Port Specifications

Page 41

Port Specifications

B

 

FE Port

The 10/100 Mbps Ethernet (FE) port is located on the right-hand side of the Aruba AP 60/61 and has an RJ-45 female connector. The port pin-outs are shown in Figure B-1:

Aruba 60/61

RJ-45 Female

 

 

 

10/100 Mbps Ethernet

Pin-Out

1

 

 

 

ETH Tx+

(POE negative*)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2

 

 

 

ETH Tx–

(POE negative*)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3

 

 

 

ETH Rx+

(POE positive*)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4

 

 

 

Serial RxD**

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

5

 

 

 

Serial RGND** (POE positive*)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

6

 

 

 

ETH Rx–

(POE positive*)

 

 

 

 

 

 

 

 

 

7

 

 

 

Serial TxD**

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

8

 

 

 

Serial TGND** (POE negative*)

 

 

 

 

 

 

 

 

 

 

 

 

Direction

 

 

 

*POE optional

Input

 

 

 

 

 

 

Output

 

 

 

**Serial optional

 

 

FIGURE B-1Aruba AP 60/61 FE Port

The appropriate cable depends on the level of connectivity required of the FE port:

zIf the connecting device supports Serial and Power Over Ethernet (SPOE), use an 8-conductor, Category 5 UTP, straight-through FE cable with a male RJ-45 connector.

The Aruba 5000 (with Line Card LC-5000-24FE-2GE-SPOE), the Aruba 2400, and the Aruba 800 support SPOE.

zIf the connecting device supports only Power Over Ethernet (POE, including IEEE 802.3af POE as well as “inline” or “midspan” POE devices), use an 8- or 4-conductor, Category 5 UTP, straight-through FE cable with male RJ-45 con- nectors.

zIf the connecting device does not support Serial or POE, use a 4- or 8-conduc- tor, Category 5 UTP, FE cable with male RJ-45 connectors. The port detects MDI/MDX and automatically adjusts for straight-through or crossover cables.

The maximum length for FE cables is 100 meters (325 feet).

When the Aruba AP 60/61 is installed in an air-handling space, as described in NEC (2002) Article 300.22 (C), POE is required. Also, any FE cable installed in such spaces should be suitable under NEC Article 800.50 and marked accordingly for use in plenums and air-handling spaces with regard to smoke propagation, such as CL2-P, CL3-P, MPP or CMP.

Aruba AP 60/61 37

Installation Guide

Image 41
Contents Aruba AP 60/61 Access Point Trademarks Aruba Wireless Networks, Inc. All rights reservedContents Appendix B Port Specifications Introduction1 Front View Antenna fixtures for Wireless Communications1Aruba AP 60/61 LEDs Indicator LEDsState Description Air VentsFE Port DC Power SocketMounting Slots Back ViewKensington Security Slot Aruba AP Setup ProcessFold-Out Stand Provisioning Access Points Aruba Discovery Protocol AP Reprovisioning AP Provisioning1Provisioning Tab 2Port Range Screen Requirements Manual ProvisioningProvisioning Access Points Console Access to the AP Connecting the Console Terminal1Console Terminal Settings Dram 32 MB Apboot setenv servername aruba-master Setting Aruba AP 60/61 ParametersMy network uses direct IP addresses instead of DNS Apboot save apboot boot Provisioning Access Points Mounting the Aruba AP 60/61 AP Deployment1Aruba AP 60/61 Mounting Options Aruba 60 Detachable AntennasAruba Description Gain Manufacturer Dbi 1FCC-Approved Detachable AntennasAP-ANT-8 2Aruba AP 60/61Fold-Out Stand Free-Standing Placement3Mounting Screw Specifications Using the Built-In Mounting Slots4Hanging the Aruba AP 60/61 on Screws Using the Optional Mounting KitsSelecting an FE Cable Connecting Required CablesConnecting Cables & Power Selecting an Antenna MaintenanceDirect Spoe Connection to Mobility Controller Accessing the AP Support PromptBaud Rate Data Bits Parity Stop Bits Flow Control 9600 None Table A-1Console Terminal SettingsDirect Terminal Connection Remote Telnet Connection Setting Telnet AccessUser Commands Access LevelsPrivileged Commands AP SupportResetting the AP to Factory Defaults Troubleshooting Figure B-1Aruba AP 60/61 FE Port FE PortSerial Breakout Adapter DB-9 SpecificationTable B-1Console Terminal Settings To Network Specifications To AP SpecificationsPort Specifications FCC Class B ComplianceUnited States RF Radiation Exposure Statement CanadaRadio Frequency Interference Requirements RSS-210Indoor Restriction for 5GHz Frequency Range Vcci Class B JapanEurope Product Specifications Measurement CertificationsRadio Characteristics Product FeaturesProduct Label Ethernet CompatibilityPackage Contents Power Over EthernetPhysical Description Optional ItemsFigure C-1Part Number AP-60 Aruba AP-60 Access PointDescription 802.11a 802.11b 802.11g Table C-1AP-60 802.11 SpecificationsACK Able C-1 AP-60 802.11 SpecificationsBssid Able C-2 AP-60 CharacteristicsAP-60 Characteristics Table C-2AP-60 Characteristics Aruba AP-61 Access PointTable C-3AP-61 802.11 Specifications Able C-4 AP-61 Characteristics Able C-3 AP-61 802.11 SpecificationsAble C-4 AP-61 Characteristics Related Documents Table C-4AP-61 CharacteristicsTable C-5Text Conventions Text ConventionsTable C-5Text Conventions Telephone Numbers Contacting Aruba NetworksProper Disposal of Aruba Equipment Product Specifications Aruba AP 60/61 W . a r u b a n e t w o r k s . c o m