Linksys Etherfast manual Vlan and Priority, Vlan Table Configuration

Page 26

EtherFast® Series

ensures that after a Leave or Leave All message has been issued, the applicants can re-join before the port actually leaves the group.

Leave All Time - The interval (centiseconds) between sending out a Leave All query message for group participants and the port leaving the group. This interval should be considerably larger than the Leave Time to minimize the amount of traffic generated by nodes rejoining the group.

VLAN and Priority

These fields set the default values for VLANs, port priority, GVRP, and GMRP.

Port VID - The VLAN ID assigned to untagged frames received on this port.

Port Default Priority - Sets the default ingress priority to any value beneath the priority threshold to specify the low priority queue, or to any value equal to or above this threshold to specify the high priority queue.

VLAN Tagging - Indicates whether or not VLAN tags will be included on frames passing through this port.

GVRP - Enables or disables GVRP for this port. When disabled, any GVRP packets received on this port will be discarded and no GVRP reg- istrations will be propagated from other ports. Note: GMVP must be enabled for the Switch before this setting can take effect.

GMRP - Enables or disables GMRP for this port. When enabled, this port will allow endstations to register with multicast groups. Note: GMRP must be enabled for the Switch before this setting can take effect.

Ingress Filtering - If enabled, incoming frames for VLANs that do not include this ingress port in their member set will be discarded at the ingress port.

Select Apply to make changes. Select OK to return to the previous panel. Select Cancel to cancel any changes. Select Prev Port to view the previous port. Select Next Port to view the next port. To display a specific port, set the port number in the Page field and then press Apply.

EtherFast® Managed 24-Port with Dual Gigabit Switch

VLAN Table Configuration

The VLAN Table Configuration screen is used to create a new VLAN or modify the settings for an existing VLAN.

VLAN - The ID for the VLAN currently displayed. The range is 1-2048.

Port - Port entries may be marked as:

(Normal) Uses GVRP to determine port membership.

S(Static) Adds port as a static entry. GVRP protocol is disabled.

R(Registration Fixed) Adds port as a static entry. GVRP protocol messages are still forwarded through this port.

X(Forbidden) Disables GVRP for this VLAN on the specified port.

Select Apply to make changes. Select OK to return to the previous panel. Select Prev Page to view the previous page. Select Next Page to view the next page. To display a specific page, set the page number in the Page field and then press Apply. Select Add to add a VLAN.

46

47

Image 26
Contents EtherFast Managed 24-Port With Dual Gigabit Switch Copyright & Trademarks Table of Contents IntroductionLEDs Getting to Know the SwitchPackage Contents Console Port RJ-45 PortsGigabit Ports Rack-Mounting the Switch Installing the SwitchPre-Installation Considerations Powering on the SwitchSwitch Management OverviewWeb Management Main Menu Configuring the SwitchLogging On to the Switch System Information Menu System InformationSwitch Information Management Setup MenuNetwork Configuration IP ConfigurationHttp Configuration IP Connectivity Test PingSerial Port Configuration Snmp ConfigurationSnmp Communities IP Trap ManagersUser Configuration Add UserConfiguration File Tftp DownloadDevice Control Menu System Mode Layer 2 MenuPort Configuration Mirror Port ConfigurationPort Trunking Configuration Static Unicast Address ConfigurationStatic Multicast Address Configuration Add Static Address EntryAdd Multicast Address Entry Bridge MenuBridge Configuration Spanning Tree Port ConfigurationVlan Port Configuration Vlan MenuVlan Table Configuration Vlan and PrioritySubnet Configuration IP MenuProtocol Configuration Add SubnetARP Configuration RIP ConfigurationStatic ARP Table Bootp Relay Database ConfigurationAdd Bootp Relay Server Add Static ARP Entry Static Route TableDefault Route Menu Add Routing EntryMAC Filtering Configuration Security MenuAdd MAC Address Filter Security ModeIP Security Filtering Configuration Add IP Address FilterIgmp Snooping Configuration Network Monitor MenuInterfaces Group Port Statistics/Statistics MenuPort Statistics Ethernet-Like Rmon Statistics Layer 2 Address Table Spanning Tree Bridge Information Spanning Tree Port InformationVlan Information Vlan Dynamic Registration Information Vlan Forwarding InformationIP Multicast Registration Table Subnet Information ARP TableRouting Table Multicast Table MenuIgmp Cache Multicast Forwarding Cache Dvmrp Routing TableDvmrp Neighbor Table System Restart MenuExit TroubleshootingCommon Problems and Solutions Tion Upgrading Firmware via the Serial Port Your firmware has now been updatedAppendix Glossary 101 103 Environmental SpecificationsWarranty Information Sales Information Tech Support RMA Issues FaxContact Information Web FTP SiteT p / / w w w. l i n k s y s . c o m