Linksys BEFW11S4 ver. 3 If you have this type Perform these steps Connection, Enter the User Name

Page 54

 

 

Instant Wireless™ Series

 

 

 

If you have this type

 

Perform these steps:

of connection:

 

 

 

 

 

Dynamic IP

1.

Select Obtain an IP automatically as the WAN

Address (DHCP)

2.

Connection Type.

 

Click the Apply button to save the setting.

Static IP Address

1.

Select Static IP as the WAN Connection Type.

 

2.

Enter the IP Address.

 

3.

Enter the Subnet Mask.

 

4.

Enter the Gateway Address.

 

5.

Enter the DNS in the 1, 2, and/or 3 fields.

 

 

You need to enter at least one DNS address.

 

6. Click the Apply button to save the settings.

 

 

 

PPPoE

1.

Select PPPoE as the WAN Connection Type.

 

2.

Enter the User Name.

 

3.

Enter the Password.

 

4. Click the Apply button to save the settings.

 

5. Click on the Status tab then on the Connect button to

 

 

launch the connection.

 

 

RAS or PPTP

If you are using RAS (Singapore SingTel) or PPTP

 

(service in Europe), check with your ISP for the

 

necessary setup information.

 

 

 

2.I’m having problems connecting to the Internet, what LEDs should be lit on the front of the Router?

•Each Router’s LED will light up for any proper connection made on the back of the Router—whether it is an Ethernet cable or power cord.

For example, the following are typical LEDs that light up once a computer and DSL modem are connected:

-When the Router is turned on (the power adapter is plugged into the Router), the Power LED lights up.

-When an Ethernet cable is properly connected between a PC and Port 4 of the Router, the Link/Act, Ful/Col, and 100 LEDs in Column 4 light up.

-ADSL modem connection causes the WAN Link LED to light up.

Wireless Access Point Router with 4-Port Switch

•My WAN Link LED isn’t lit. What should I check?

-Check that the cable you are using between your ADSL modem

and the Router is the same cable that came with your modem. Depending on the type of connection your modem uses, you may need either a

“straight-through” or “crossover” Ethernet cable (the “straight-through” type is more common).

•Some of the lights on the front of the Router don’t light up when I plug in a PC.

-Only the Link/Act LED is required for a connection to work correctly.

3.I cannot get onto the Internet, nor can I access the Router’s Setup page. What should I check?

A.First check that the ADSL modem and computers are properly connected to the Router. See Question #2 for how to verify that the connections are good.

B.Then, check that you have properly configured your PCs to communicate with the Router. Below you will find instructions for the various versions of Windows.

-Windows 98 SE, or ME

•Click the Start menu, and then click Run. After the Run window appears, enter winipcfg in the Open field, and then click the OK button.

•When the IP Configuration window appears, click the gray box with a black arrow pointing down.

•A list of adapters will appear. Select the adapter that you use to connect to the Internet. These items should not contain “PPP”, “VPN”, “AOL”, or “Dial-Up adapter” as part of the entry.

•The IP Address field should show an IP address of 192.168.1.100 or 192.168.1.xxx, with “xxx” being any number greater than 100.

If your IP address is not in that range, hold the reset button on the front of the Router for more than 30 seconds. This will cause your Router to be set to factory default, so you will need to re-configure the Router's Setup page. After re-configuring the Setup page, restart the computer.

-Windows NT, 2000, and XP

•Click the Start menu, and then click Run. After the Run window appears, enter cmd in the Open field, and then click the OK button.

•This will open a command prompt. Enter ipconfig /all and then press the Enter key.

106

107

Page 53 Page 55
Image 54
Page 53 Page 55
Contents Wireless Access Point Router with 4-Port Switch Instant Wireless SeriesTable of Contents Table des matières Introduction Possibilités offertesLocal du routeur. Recommencez Passez à l’étape 2 configuration des PC page suivanteÉtape 1 connexion du routeur Connecter au routeurÉtape 2 configuration des PC Vous le demande pas, redémarrez quand même l’ordinateurWindows Au réseau local répertoriée. Double-cliquezÉtape 3 configuration du routeur Routeur de point d’accès sans fil avec commutateur 4 ports Modifier le Ssid AideSécuriser votre réseau sans fil Activer le WEPSi vous avez ce type Procédez comme suit De connexion Instant Wireless Series Configuration de la sécurité sans fil Figure C-1Configuration de la sécurité sans fil dans Windows XP Figure C-4 Figure C-8 Inhoud Inleiding 10/100 Workgroup HubsStap 1 Sluit de router aan Stap 1 Sluit de router aanStap 2 Configureer de pc’s Elke pc die u wenst aan te sluitenLocal Area Connection Stap 3 Configureer de router HetPictogram voor de betreffende Ethernet De naam van uw draadloos VervolledigVelden Het PPPoEVerander de Ssid RaadpleegtBeveiliging van uw draadloos netwerk Activeer WEP-encryptieHelp Configuratie van Windows-instellingen De WAN Link LED licht niet op. Wat moet ik controleren?Klik op de Connections-tab in het Internet Options-venster Configuratie van de draadloze beveiliging Figuur C-1 Figuur C-2Figuur C-3 Figuur C-4Figuur C-5 Figuur C-9 Figuur C-6Figuur C-7 Figuur C-8Figuur C-10 Inhaltsverzeichnis Schritt 2 Konfigurieren der PCs EinführungSchritt 1 Anschließen des Routers Schritt 3 Konfigurieren des RoutersSchritt 1 Anschließen des Routers PC, den Sie an den RouterWindows oder nach zusätzlichen Dateien Schritt 2 Konfigurieren der PCsNetzwerk zu öffnen An, z. B. D\win98Starten Sie Ihren Computer neu Deaktivieren?Schritt 3 Konfigurieren des Routers DieSsid lautet linksys. Sie sollten PPPoE Führ diese Schritte aus Linksys unter support.linksys.comHilfe Ihren Benutzernamen Ihr KennwortVerbindungstyp Führen Sie diese Schritte aus Wie kann ich die Betriebsreichweite des Routers verbessern? Konfigurieren der Wireless-Sicherheit Abbildung C-2Abbildung C-1 Konfigurieren der Wireless-Sicherheit unter Windows XP Abbildung C-3Abbildung C-5 Abbildung C-4Abbildung C-6 Abbildung C-7Abbildung C-8 Abbildung C-9Abbildung C-10 Copyright & Trademarks Wireless Access Point Router with 4-Port Switch But what does all of this mean?Connect an Ethernet cable to Proceed to Configure the PCs on the nextConnect the Router LAN ports. Repeat this processConfigure the PCs If Windows asks you to restart your PCCheck Never Dial Up a Connection. E. Click the Apply button Your Configure the RouterUnique name For 101103 Activate MAC-address control list Change / activate passwordsActivate WEP 105Enter the Password Click the Apply button to save the settingClick the Apply button to save the settings Service in Europe, check with your ISP for109 Configuring Wireless Security 111Configuring Wireless Security in Windows XP 113115 Ssid 117119 Copyright 2003 Linksys, All Rights Reserved
Top Page Image Contents