NETGEAR DGND3300 user manual Lan Tcp/Ip

Page 73

RangeMax Dual Band Wireless-N Modem Router DGND3300 User Manual

Table 5-1. LAN Setup

Settings

 

Description

 

 

 

LAN TCP/IP

IP Address

The LAN IP address of the modem router.

Setup

 

 

IP Subnet Mask

The LAN subnet mask of the modem router. Combined with

 

 

 

the IP address, the IP Subnet Mask allows a device to know

 

 

which other addresses are local to it, and which must be

 

 

reached through a gateway or modem router.

 

 

 

 

RIP Direction

RIP (Router Information Protocol) allows a modem router to

 

 

exchange routing information with other routers. This

 

 

setting controls how the modem router sends and receives

 

 

RIP packets. Both is the default.

 

 

Both or Out Only. The modem router broadcasts its

 

 

routing table periodically.

 

 

Both or In Only. The modem router incorporates the RIP

 

 

information that it receives.

 

 

None. The modem router will not send any RIP packets

 

 

and will ignore any RIP packets received.

 

RIP Version

This controls the format and the broadcasting method of the

 

 

RIP packets that the modem router sends. It recognizes

 

 

both formats when receiving. By default, this is RIP-1.

 

 

RIP-1 is universally supported. It is adequate for most

 

 

networks, unless you have an unusual network setup.

 

 

RIP-2 carries more information. Both RIP-2B and RIP-2M

 

 

send the routing data in RIP-2 format. RIP-2B uses

 

 

subnet broadcasting. RIP-2M uses multicasting.

DHCP Server

Use Router as a DHCP

This check box is usually selected so that the modem router

For more

Server

functions as a Dynamic Host Configuration Protocol

information

 

(DHCP) server. See “Using the Modem Router as a DHCP

 

 

Server” on page 5-4.

 

 

 

 

Starting IP Address

Specify the start of the range for the pool of IP addresses in

 

 

the same subnet as the modem router.

 

 

 

 

Ending IP Address

Specify the end of the range for the pool of IP addresses in

 

 

the same subnet as the modem router.

 

 

 

Address Reservation

When you specify a reserved IP address for a computer on

For more information, see “Address

the LAN, that computer receives the same IP address each

Reservation” on page 5-4.

time it access the modem router’s DHCP server. Assign

 

 

reserved IP addresses to servers that require permanent IP

 

 

settings.

 

 

 

Customizing Your Network Settings

5-3

v1.0, March 2009

Image 73
Contents NETGEAR, Inc Trademarks Product Registration, Support, and DocumentationStatement of Conditions Certificate of the Manufacturer/ImporterEurope EU Declaration of Conformity FCC Guidelines for Human Exposure FCC Information to UserFCC Radio Frequency Interference Warnings & Instructions FCC Declaration Of ConformityProduct and Publication Details Contents Chapter Protecting Your Network Appendix B Related Documents Index V1.0, March Conventions, Formats, and Scope About This ManualHow to Print This Manual How to Use This ManualPublication Revision History Revision HistoryVersion Date Description V1.0 March Original publication Xiv Using the Setup Manual Chapter Configuring Your Internet ConnectionDocument in Preparing Your Network in Appendix B Logging In to Your Modem RouterV1.0, March Using the Setup Wizard Viewing or Manually Configuring Your ISP Settings ISP does not require login Settings Description Basic Settings screen fieldsGet Automatically from ISP. Your ISP uses Dhcp to Xxxxxxxxxxxx Configuring Adsl SettingsV1.0, March V1.0, March Planning Your Wireless Network Chapter Safeguarding Your NetworkSee Manually Configuring Your Wireless Settings on Wireless Placement and Range GuidelinesWireless data Security options Range up to 300 foot radius Wireless Security OptionsManually Configuring Your Wireless Settings Wireless Settings WPA-802.1x Configuring WEP Wireless SecurityNetwork Key 8-63 characters Security Options section, select the WEP radio button Configuring WPA, WPA2, or Mixed WPA2 + WPA Wireless Security V1.0, March Using Push N Connect WPS to Configure Your Wireless Network Using a WPS Button to Add a WPS Client Using PIN Entry to Add a WPS Client Configuring Advanced WPS Settings Adding More WPS Clients Adding Both WPS and Non-WPS Clients Enable Wireless Router Radio Restricting Access to Your Modem RouterV1.0, March V1.0, March Chapter Protecting Your Network Protecting Access to Your Modem RouterChanging the Built-In Password Restricting Access by MAC AddressSelect the Turn Access Control On checkbox Blocking Access to Internet Sites V1.0, March Firewall Rules Field Outbound Rules Inbound Rules Adding or Editing Firewall Service RulesBlocking Access to Internet Services V1.0, March Scheduling Blocking Log Entry Descriptions Viewing Logs of Web Access or Attempted Web AccessField Description Configuring E-mail Alert and Web Access Log Notifications Setting the Time V1.0, March Upgrading the Firmware Chapter Using Network Monitoring ToolsManually Checking for Firmware Upgrades V1.0, March Viewing Modem Router Status Information Dhcp Modem Router Status FieldsConnection Status Statistics Connection Status SettingsModem Router Statistics Viewing a List of Attached Devices Backing Up and Restoring the Configuration Managing the Configuration FileErasing the Configuration Running Diagnostic Utilities and Rebooting the Modem Router Select the Turn Remote Management On check box Enabling Remote Management AccessV1.0, March V1.0, March Using the LAN Setup Options Chapter Customizing Your Network SettingsSettings LAN SetupLAN TCP/IP Address Reservation Using the Modem Router as a Dhcp ServerUsing a Dynamic DNS Service Select the Use a Dynamic DNS Service check box WAN Setup Settings Configuring the WAN Setup OptionsSetting Description WAN Port Setting Up a Default DMZ ServerConfiguring QoS for Internet Access Setting up Quality of Service QoSQoS for Applications and Online Gaming QoS for a Router LAN Port QoS for a MAC Address Editing or Deleting an Existing QoS Policy Configuring Static Routes V1.0, March Wireless Repeating Also Called WDS Wireless Repeating Function Setting Up the Base Station Fill in the Base Station MAC Address field Setting Up a Repeater UnitV1.0, March Chapter Fine-Tuning Your Network Assessing Your Speed Requirements Theoretical Transfer Time for 1 Gigabyte Optimizing Your Network BandwidthNetwork Connection Theoretical Raw Transfer Time RangeMax Dual Band Wireless-N Modem Router Identify critical wireless links Optimizing Wireless PerformanceChanging the MTU Size Choose your settingsCommon MTU Sizes Universal Plug and PlayApplication V1.0, March Quick Tips Chapter TroubleshootingQuick Tips Recommendation InstructionsTroubleshooting with the LEDs Situation Recommended Action Troubleshooting with the LEDsCannot Access the Router Menu Checking the Configuration Cannot Access the InternetChecking the WAN IP Address V1.0, March Testing the LAN Path to Your Router Troubleshooting a Network Using the Ping UtilityPing -n 10 IP address Testing the Path from Your Computer to a Remote DeviceWireless Connectivity Problems with Date and TimeViewing Available Networks Using the Restore Factory Settings Button Restoring the Factory Configuration SettingsFeature Default Setting Router login Table A-1. Default Configuration SettingsInternet connection Local network LANTable A-1. Specifications Technical SpecificationsFeature Default Setting Wireless Power AdapterEnvironmental Interface SpecificationsRegulatory Compliance Document Link Appendix B Related DocumentsV1.0, March Index Index-2 Index-3 Index-4