Adder Technology CATxIP 1000 manual Radio Frequency Energy, European EMC directive 89/336/EEC

Page 89

Radio Frequency Energy

A Category 5 (or better) twisted pair cable must be used to connect the units in order to maintain compliance with radio frequency energy emission regulations and ensure a suitably high level of immunity to electromagnetic disturbances.

All other interface cables used with this equipment must be shielded in order to maintain compliance with radio frequency energy emission regulations and ensure a suitably high level of immunity to electromagnetic disturbances.

European EMC directive 89/336/EEC

This equipment has been tested and found to comply with the limits for a class A computing device in accordance with the specifications in the European standard EN55022. These limits are designed to provide reasonable protection against harmful interference. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio or television reception. However, there is no guarantee that harmful interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment on and off, the user is encouraged to correct the interference with one or more of the following measures: (a) Reorient or relocate the receiving antenna. (b) Increase the separation between the equipment and the receiver. (c) Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. (d) Consult the supplier or an experienced radio/TV technician for help.

FCC Compliance Statement (United States)

This equipment generates, uses and can radiate radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer’s instructions, may cause interference to radio communication.

It has been tested and found to comply with the limits for a class A computing device in accordance with the specifications in Subpart J of part 15 of FCC rules, which are designed to provide reasonable protection against such interference when the equipment is operated in a commercial environment. Operation of this equipment in a residential area may cause interference, in which case the user at his own expense will be required to take whatever measures may be necessary to correct the interference. Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.

Canadian Department of Communications RFI statement

This equipment does not exceed the class A limits for radio noise emissions from digital apparatus set out in the radio interference regulations of the Canadian Department of Communications.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de la classe A prescrites dans le règlement sur le brouillage radioélectriques publié par le ministère des Communications du Canada.

   



88

Image 89
Contents AdderView CATxIP Contents Further information Index CAM formats Global usersMany computers AdderView CATxIP 1000 features front and rear What you may additionally need What’s in the boxDouble unit rack brackets MountingSingle unit rack brackets Connections CAM Computer Power System SwitchTo connect the local user port Local userTo connect the Global user IP network port Global user IP network portAdderView CATxIP Front panel Category 5, 5e or 6 cable from Adder X100/X200 moduleTo connect a computer system Computer system via CAMOutput lead from Power adapter Power in connectionTo connect the power supply Switch Power control portTo connect and address the switch boxes Cascade tree Cascading multiple unitsSee also To connect units in cascade Connecting units in cascadeTips for successful cascading Addressing computers in a cascade Using cascaded computersUSB-type and that it is plugged Multiple video head connectionsIt is recommended that Second CAM in each pair is a Cable from serial Control device Remote switching controlHost computer port/channel Video off Overall initial configuration ConfigurationInitial configuration Menu layout Main menuHotkeys SecurityTo enable general security General security and configuration stepsTo set an Admin password Registering users and host computersTo clear a password and restore factory default settings What to do if the Admin password has been forgottenTo clear IP access control Clearing IP access controlWhat is IP access control? To configure the unit from a global user location Full configuration by global userViewer encryption settings Encryption settingsAdderView CATxIP 1000 encryption settings Positioning AdderView CATxIP 1000 in the network Networking issuesPlacing AdderView CATxIP 1000 behind a router or firewall Port settingsAddressing Firewall/router addressDNS addressing To discover a DHCP-allocated IP addressPorts Placing AdderView CATxIP 1000 alongside the firewallEnsuring sufficient security Power control sequences Power switching configurationTo configure the power sequences for each host computer To control two or more ports simultaneouslyTo upgrade AdderView CATxIP 1000 models Recovering from a failed upgradeTo invoke backup/recovery mode Upgrading AdderView CATxIP 1000 modelsFront panel indicators Accessing the AdderView CATxIPSelecting a computer Local user accessSelect Host menu here you can select computers by name To select a computer using the Select Host menuStandard hotkeys To select a computer using mouse buttons Advanced method To select a computer using mouse buttonsLogging in and out To logTo change banner colours or disable the banner To enable/disable the confirmation boxConfirmation box Reminder bannerUser preferences and functions Blue dot indicators in the Select Host menuGlobal User Global user accessTo access via the VNC viewer Global user access via VNC viewerTo download the VNC viewer Options buttonTo access via your web browser Global user access via web browserMenu bar Using the viewer windowWhen using the viewer window Mouse pointers ConfigureHost selection To select a hostPower switching Access mode shared/privateAuto calibrate Re-synchronise mouseControls Video Settings When entering codesKeyboard Control EnterIncreased by 50% when a slow link is detected Using automatic configurationsSetting the Threshold manually AccordinglyOverlap Capture Advanced SettingsCustom Video Modes Supported web browsers Viewer encryption settingsIf you need to enter a port number When logging on using VNC viewer, I cannot enter a username TroubleshootingGetting assistance US +1 888 275To access the local setup menus Appendix 1 Local setup menusRestore Standard Mouse Power ControlRestore Intellimouse FunctionsReminder Banner User PreferencesReminder Colour Screen SaverUser Timeout Mouse SwitchingGlobal Preferences OSD Dwell TimeAuto Logout Setup OptionsIP admin password, encryption settings, etc ConfigurationCompletely resets the AdderView CATxIP 1000 unit IP address, net mask, VNC port, etcUnit Configuration Network Configuration Settings Power Control, Sync Units Serial ConfigurationSettings 1200, 2400, 4800, 9600, 19200, 38400, 57600 Options PortTo reset the AdderView CATxIP 1000 configuration Reset ConfigurationMain configuration Logged on users Appendix 2 Configuration pages via viewerTo access the remote configuration pages User accounts Unit configuration Advanced unit configuration Time & date configuration IP Access Control Network configurationIP Network Mask IP GatewayTo define a new IP access control entry Setting IP access controlTo reorder access control entries To edit/remove access control entriesBaud Rate Serial port configurationOptions Port Use Erase Host Configuration Host configurationAdd entry for unrecognised host To create a new host entryTo copy and paste the log Logging and statusSyslog Server IP Address For further details To get hereLdap configuration Colour/Encoding Appendix 3 VNC viewer connection optionsAuto select Preferred encodingDisable all inputs view-only mode Enable all inputsInputs CustomiseMisc No Scaling ScalingScale to Window Size Custom SizeDefaults Save Defaults ReloadIdentities Load / SaveAppendix 4 VNC viewer window options Security Appendix 5 Browser viewer optionsEncoding and colour level Net masks Appendix 6 Addresses, masks and portsIP addresses Operation with net mask Net masks the binary explanationBinary equivalent Binary octet afterSingle locations Calculating the mask for IP access controlAll locations Address rangesPorts Security issues with portsPower switch to power switch daisy chain cable Appendix 7 Cable and connector specificationsAdderView CATxIP 1000 to power switch cable Creating macro sequences Appendix 8 Hotkey sequence codesPermissible key presses Appendix 9 Supported video modes General Public License Linux WarrantySafety information End user licence agreement European EMC directive 89/336/EEC Radio Frequency EnergyFCC Compliance Statement United States Canadian Department of Communications RFI statementHoe Huat Industrial Building Index 