Actiontec electronic V.90 ISA user manual Configuring Windows

Page 14

Configuring Windows 98

Step 1 After you have installed the modem hardware in your computer, plug the computer back into the wall outlet. Turn on the power and allow the system to boot normally.

Step 2 Windows 98 will immediately display the Add New Hardware Wizard and identify the modem as a “56K V.90 Fax/Modem (LKT)”. Click the Next button.

Step 3 At the next dialog box, make sure that “Search for the best driver for your device. (Recommended)” is selected, and then click Next.

14

Image 14

Contents ISA Plug n Play Voice/Fax Modem Table of Contents Introduction Contacting Actiontec Customer SupportFor Windows 95/98 Installation Before You BeginFor Windows NT 4.0 Installation Installing The Modem Hardware InstallationInstalling The Modem Connecting Devices to the Modem Connecting DevicesConfiguring Windows Page Configuring Windows 95 OSR2 FinishPage Page Configuring Windows Page Page Page Page Configuring Windows NT Page Page Page Page Init String Installing Communications SoftwareFax TIA/EIA-578 for Class 1 Fax Voice AT&F&C1&D2W2Troubleshooting Windows 95/98More Info Panel Common Problems No Dialtone ErrorCommunications Software Does Not Work Appendix a Non Plug-N-Play Installations COM Ports and InterruptsJumper Settings Jumpers Set To Plug-N-Play default setting Remove Installing In DOS and WindowsHardware and Driver Installation Page Answer Command Appendix B AT Command SetRepeat Last Command ATXnResult Codes Carrier ControlDnDial Last number dialedHook Control Echo CommandOnline Data Character Echo Command Request ID Information Monitor Speaker VolumeThis command sets speaker volume to low, medium, or high This command turns the speaker on or off Modulation HandshakeResult Code Control Return On-line to Data ModeSelect Pulse Dialing DCE Response Format Result Code OptionExtended Result Codes Dial Tone DetectLong Space Disconnect Long space disconnect is always disabledBusy Tone Detect Recall Stored ProfileData Carrier Detect DCD Control Auto RetrainThis modem always auto retrains Load Factory Settings DTR ControlAuxiliary Relay option Local Flow Control SelectionPulse Dial Make-to-Break Ratio Selection Asynchronous Communications ModeThis Command is effective only for use in Japan This command selects DSR action Data Set Ready DSR OptionThis command is used to display the active profiles Below is an example of a possible outputSSE \Bn Zn=x\An Adjust Bits/s Rate Control Modem Port Flow Control\Kn \Nn Error Control Mode Selection = 0, 1, 2, 3, 4, 5 \Xn XON/XOFF Pass Through \Tn Inactivity Timer\Vn Protocol Result Code View Numbers in Blacklist Enable/Disable Data CompressionData Calling Tone Write to/Read from DSP Register AT Commands for Testing and DebuggingSelf-Test Commands Line-to-Line LoopbackATI11 Registers Reference TypeRange −127, Ascii decimal Default Carriage return Units Range 0−255 Default UnitsringsRange 0−255 Default UnitsASCII Range −127, Ascii decimal Default Line feed UnitsConnection Completion Time-Out Range −32 Default Backspace UnitsRange Default Unitsseconds Comma Dial Modifier TimeS12 Escape Guard Time S10S11 Dtmf Dialing Speed S14 General Bit Mapped Options StatusS22 S24 Timer to Control Sleep ModeS21 S32 S28 Modulation Enable/DisableS30 Inactivity Timer S33S36 S37 Dial Line Rate defaultS38 56K Dial Line Rate default ConnectionS48 Lapm Error Control and Feature Negotiation default S42 Auto Rate default 1, rangeS43 Auto Mode default 1, range S91 S89 Timer to Control Sleep ModeS90 S92S109K56flex and V.90 Selection default No CarrierResult Code Appendix B Communications Regulations Declaration of ConformityCanadian Department of Communications Cdoc