Actiontec electronic V.90 ISA user manual Extended Result Codes, Dial Tone Detect

Page 42

Xn	Result Code Selection and Call Progress Monitoring

This command enables tone detection options used in the dialing process. As these functions are chosen, the result codes are also affected. Therefore, this command is frequently used to control the modem chipset’s responses. The primary function of this control is to control the modem chip set’s call response capabilities.

Command	Result Code	Dial Tone Detect	Busy Tone Detect

X0	Disable	Disable	Disable

X1	Enable	Disable	Disable

X2	Enable	Enable	Disable

X3	Enable	Disable	Enable

X4	Enable	Enable	Enable (default)

X5	Enable	Enable	Enable

X6	Enable	Enable	Enable

X7	Disable	Enable	Enable

Extended Result Codes

	Extended	Effect
	Result Codes	Effect
	Result Codes

	Disabled	Displays only the basic result codes OK, CONNECT,
	Disabled	RING, NO CARRIER, and ERROR.
		RING, NO CARRIER, and ERROR.

		Displays basic result codes, along with the connect
	Enabled	message and the modem’s data rate, and an
	Enabled	indication of the modem’s error correction and data
		indication of the modem’s error correction and data
		compression operation.

	Dial Tone Detect

	Dial Tone	Effect
	Detect	Effect
	Detect

		The modem dials a call regardless of whether it detects
	Disabled	a dial tone. The period of time the modem waits before
		dialing is specified in register S6.

		The modem dials only upon detection of a dial tone,
	Enabled	and disconnects the call if the dial tone is not detected
		within 10 seconds.

42

Image 42

Contents ISA Plug n Play Voice/Fax Modem Table of Contents Introduction Contacting Actiontec Customer SupportFor Windows 95/98 Installation Before You BeginFor Windows NT 4.0 Installation Installing The Modem Hardware InstallationInstalling The Modem Connecting Devices to the Modem Connecting DevicesConfiguring Windows Page Configuring Windows 95 OSR2 FinishPage Page Configuring Windows Page Page Page Page Configuring Windows NT Page Page Page Page Init String Installing Communications SoftwareFax TIA/EIA-578 for Class 1 Fax Voice AT&F&C1&D2W2Troubleshooting Windows 95/98More Info Panel Common Problems No Dialtone ErrorCommunications Software Does Not Work Appendix a Non Plug-N-Play Installations COM Ports and InterruptsJumper Settings Jumpers Set To Plug-N-Play default setting Installing In DOS and Windows Hardware and Driver InstallationRemove Page Answer Command Appendix B AT Command SetRepeat Last Command ATXnResult Codes Carrier ControlDnDial Last number dialedEcho Command Online Data Character Echo CommandHook Control Monitor Speaker Volume This command sets speaker volume to low, medium, or highRequest ID Information This command turns the speaker on or off Modulation HandshakeReturn On-line to Data Mode Select Pulse DialingResult Code Control DCE Response Format Result Code OptionExtended Result Codes Dial Tone DetectLong Space Disconnect Long space disconnect is always disabledBusy Tone Detect Recall Stored ProfileAuto Retrain This modem always auto retrainsData Carrier Detect DCD Control Load Factory Settings DTR ControlAuxiliary Relay option Local Flow Control SelectionAsynchronous Communications Mode This Command is effective only for use in JapanPulse Dial Make-to-Break Ratio Selection This command selects DSR action Data Set Ready DSR OptionThis command is used to display the active profiles Below is an example of a possible outputSSE Zn=x \An\Bn Adjust Bits/s Rate Control Modem Port Flow Control\Kn \Nn Error Control Mode Selection = 0, 1, 2, 3, 4, 5 \Tn Inactivity Timer \Vn Protocol Result Code\Xn XON/XOFF Pass Through Enable/Disable Data Compression Data Calling ToneView Numbers in Blacklist Write to/Read from DSP Register AT Commands for Testing and DebuggingSelf-Test Commands Line-to-Line LoopbackATI11 Registers Reference TypeRange −127, Ascii decimal Default Carriage return Units Range 0−255 Default UnitsringsRange 0−255 Default UnitsASCII Range −127, Ascii decimal Default Line feed UnitsConnection Completion Time-Out Range −32 Default Backspace UnitsRange Default Unitsseconds Comma Dial Modifier TimeS12 Escape Guard Time S10S11 Dtmf Dialing Speed S14 General Bit Mapped Options StatusS24 Timer to Control Sleep Mode S21S22 S32 S28 Modulation Enable/DisableS30 Inactivity Timer S33S36 S37 Dial Line Rate defaultS38 56K Dial Line Rate default ConnectionS42 Auto Rate default 1, range S43 Auto Mode default 1, rangeS48 Lapm Error Control and Feature Negotiation default S91 S89 Timer to Control Sleep ModeS90 S92S109K56flex and V.90 Selection default No CarrierResult Code Appendix B Communications Regulations Declaration of ConformityCanadian Department of Communications Cdoc