Actiontec electronic V.90 ISA user manual Return On-line to Data Mode, Select Pulse Dialing

Page 40

On

Return On-line to Data Mode

 

 

 

 

 

 

Command

Effect

 

 

 

 

 

 

O0

 

Instructs the modem to exit on-line command mode and

 

 

return to data mode (see AT Escape Sequence, +++).

 

 

 

 

 

 

 

 

 

O1

 

This command issues a retrain before returning to on-

 

 

line data mode.

 

 

 

 

 

 

 

 

 

O3

 

This command issues a rate renegotiation before

 

 

returning to online data mode.

 

 

 

 

 

 

 

 

Result Codes:

 

 

 

 

 

 

 

 

OK

n = 0, 1, 3

 

 

 

 

 

 

ERROR

Otherwise

 

 

 

 

 

P

Select Pulse Dialing

This command configures the modem for pulse (non-touch-tone) dialing. Dialed digits are pulsed until a T command or dial modifier is received. Tone dial is the default setting.

Qn

Result Code Control

Result codes are informational messages sent from the modem and displayed on your monitor. Basic result codes are OK, CONNECT, RING, NO CARRIER, and ER- ROR. The ATQ command allows the user to turn result codes on or off.

Command

Effect

 

 

Q0

Enables modem to send result codes to the computer

(default).

 

 

 

Q1

Disables modem from sending result codes to the

computer.

 

 

 

Result Codes:

OK

n = 0, 1

ERROR Otherwise

40

Page 39 Page 41
Image 40
Page 39 Page 41
Contents ISA Plug n Play Voice/Fax Modem Table of Contents Introduction Contacting Actiontec Customer SupportFor Windows 95/98 Installation Before You BeginFor Windows NT 4.0 Installation Installing The Modem Hardware InstallationInstalling The Modem Connecting Devices to the Modem Connecting DevicesConfiguring Windows Page Configuring Windows 95 OSR2 FinishPage Page Configuring Windows Page Page Page Page Configuring Windows NT Page Page Page Page Installing Communications Software Fax TIA/EIA-578 for Class 1 Fax VoiceInit String AT&F&C1&D2W2Troubleshooting Windows 95/98More Info Panel Common Problems No Dialtone ErrorCommunications Software Does Not Work Appendix a Non Plug-N-Play Installations COM Ports and InterruptsJumper Settings Jumpers Set To Plug-N-Play default setting Hardware and Driver Installation Installing In DOS and WindowsRemove Page Appendix B AT Command Set Repeat Last CommandAnswer Command ATXnResult Codes Carrier ControlDnDial Last number dialedOnline Data Character Echo Command Echo CommandHook Control This command sets speaker volume to low, medium, or high Monitor Speaker VolumeRequest ID Information This command turns the speaker on or off Modulation HandshakeSelect Pulse Dialing Return On-line to Data ModeResult Code Control DCE Response Format Result Code OptionExtended Result Codes Dial Tone DetectLong space disconnect is always disabled Busy Tone DetectLong Space Disconnect Recall Stored ProfileThis modem always auto retrains Auto RetrainData Carrier Detect DCD Control Load Factory Settings DTR ControlAuxiliary Relay option Local Flow Control SelectionThis Command is effective only for use in Japan Asynchronous Communications ModePulse Dial Make-to-Break Ratio Selection This command selects DSR action Data Set Ready DSR OptionThis command is used to display the active profiles Below is an example of a possible outputSSE \An Zn=x\Bn Adjust Bits/s Rate Control Modem Port Flow Control\Kn \Nn Error Control Mode Selection = 0, 1, 2, 3, 4, 5 \Vn Protocol Result Code \Tn Inactivity Timer\Xn XON/XOFF Pass Through Data Calling Tone Enable/Disable Data CompressionView Numbers in Blacklist AT Commands for Testing and Debugging Self-Test CommandsWrite to/Read from DSP Register Line-to-Line LoopbackATI11 Registers Reference TypeRange 0−255 Default Unitsrings Range 0−255 Default UnitsASCIIRange −127, Ascii decimal Default Carriage return Units Range −127, Ascii decimal Default Line feed UnitsRange −32 Default Backspace Units Range Default UnitssecondsConnection Completion Time-Out Comma Dial Modifier TimeS10 S11 Dtmf Dialing SpeedS12 Escape Guard Time S14 General Bit Mapped Options StatusS21 S24 Timer to Control Sleep ModeS22 S28 Modulation Enable/Disable S30 Inactivity TimerS32 S33S37 Dial Line Rate default S38 56K Dial Line Rate defaultS36 ConnectionS43 Auto Mode default 1, range S42 Auto Rate default 1, rangeS48 Lapm Error Control and Feature Negotiation default S89 Timer to Control Sleep Mode S90S91 S92S109K56flex and V.90 Selection default No CarrierResult Code Appendix B Communications Regulations Declaration of ConformityCanadian Department of Communications Cdoc
Top Page Image Contents