Actiontec electronic V.90 ISA user manual Tn Inactivity Timer, Vn Protocol Result Code

Page 56

\Tn	Inactivity Timer

This command specifies the length of time (in minutes) that the modem will wait before disconnecting when no data is sent or received. A setting of zero disables the timer. Alternatively, this timer may be specified in register S30. This function is only applicable to buffer mode.

Result Codes:

	OK	n = 0-255

	ERROR	Otherwise

\Vn		Protocol Result Code

	Command		Effect

	\V0		Disable protocol result code

	\V1		Enable protocol result code

	\V2		Enable protocol result code

Result Codes:

	OK	n = 0, 1, 2

	ERROR	Otherwise

\Xn		XON/XOFF Pass Through

	Command		Effect

	\X0		Modem processes XON/XOFF flow control characters
	\X0		locally (default)
			locally (default)

	\X1		Modem processes and pass XON/XOFF flow control
	\X1		characters
			characters

Result Codes:

	OK	n = 0, 1

	ERROR	Otherwise

56

Image 56

Contents ISA Plug n Play Voice/Fax Modem Table of Contents Introduction Contacting Actiontec Customer SupportFor Windows 95/98 Installation Before You BeginFor Windows NT 4.0 Installation Installing The Modem Hardware InstallationInstalling The Modem Connecting Devices to the Modem Connecting DevicesConfiguring Windows Page Configuring Windows 95 OSR2 FinishPage Page Configuring Windows Page Page Page Page Configuring Windows NT Page Page Page Page Installing Communications Software Fax TIA/EIA-578 for Class 1 Fax VoiceInit String AT&F&C1&D2W2Troubleshooting Windows 95/98More Info Panel Common Problems No Dialtone ErrorCommunications Software Does Not Work Appendix a Non Plug-N-Play Installations COM Ports and InterruptsJumper Settings Jumpers Set To Plug-N-Play default setting Remove Installing In DOS and WindowsHardware and Driver Installation Page Appendix B AT Command Set Repeat Last CommandAnswer Command ATXnResult Codes Carrier ControlDnDial Last number dialedHook Control Echo CommandOnline Data Character Echo Command Request ID Information Monitor Speaker VolumeThis command sets speaker volume to low, medium, or high This command turns the speaker on or off Modulation HandshakeResult Code Control Return On-line to Data ModeSelect Pulse Dialing DCE Response Format Result Code OptionExtended Result Codes Dial Tone DetectLong space disconnect is always disabled Busy Tone DetectLong Space Disconnect Recall Stored ProfileData Carrier Detect DCD Control Auto RetrainThis modem always auto retrains Load Factory Settings DTR ControlAuxiliary Relay option Local Flow Control SelectionPulse Dial Make-to-Break Ratio Selection Asynchronous Communications ModeThis Command is effective only for use in Japan This command selects DSR action Data Set Ready DSR OptionThis command is used to display the active profiles Below is an example of a possible outputSSE \Bn Zn=x\An Adjust Bits/s Rate Control Modem Port Flow Control\Kn \Nn Error Control Mode Selection = 0, 1, 2, 3, 4, 5 \Xn XON/XOFF Pass Through \Tn Inactivity Timer\Vn Protocol Result Code View Numbers in Blacklist Enable/Disable Data CompressionData Calling Tone AT Commands for Testing and Debugging Self-Test CommandsWrite to/Read from DSP Register Line-to-Line LoopbackATI11 Registers Reference TypeRange 0−255 Default Unitsrings Range 0−255 Default UnitsASCIIRange −127, Ascii decimal Default Carriage return Units Range −127, Ascii decimal Default Line feed UnitsRange −32 Default Backspace Units Range Default UnitssecondsConnection Completion Time-Out Comma Dial Modifier TimeS10 S11 Dtmf Dialing SpeedS12 Escape Guard Time S14 General Bit Mapped Options StatusS22 S24 Timer to Control Sleep ModeS21 S28 Modulation Enable/Disable S30 Inactivity TimerS32 S33S37 Dial Line Rate default S38 56K Dial Line Rate defaultS36 ConnectionS48 Lapm Error Control and Feature Negotiation default S42 Auto Rate default 1, rangeS43 Auto Mode default 1, range S89 Timer to Control Sleep Mode S90S91 S92S109K56flex and V.90 Selection default No CarrierResult Code Appendix B Communications Regulations Declaration of ConformityCanadian Department of Communications Cdoc