Actiontec electronic V.90 ISA Appendix B Communications Regulations, Declaration of Conformity

Page 71

Appendix B: Communications Regulations

FCC REGULATIONS

The following statements are provided in accordance with the Federal Communica- tions Commission (FCC) regulations. Please read these statements carefully before installing your modem.

FCC PART 68 REQUIREMENTS

This equipment complies with Part 68 of the FCC Rules. On the bottom of this equipment is a label that contains, among other information, the FCC Registration Number and Ringer Equivalence Number (REN) for this equipment. If requested, this information must be given to the telephone company.

The REN is used to determine the maximum number of devices connected to your telephone line that will ring in response to an incoming call. In most, but not all, areas, the total REN of devices connected to a line should not exceed five (5.0). To find out the total permitted in your area, contact your local telephone company.

If your telephone equipment causes harm to the telephone network, the telephone company can discontinue your service temporarily. If possible, the company will notify you in advance. But if advance notice isn’t practical, you will be notified as soon as possible. You will be informed of your right to file a complaint with the FCC.

Your telephone company can make changes in its facilities, equipment, operations, or procedures that could affect the operation of your equipment. If so, you will be notified in advance so you can make the changes needed to maintain uninterrupted service.

If you experience trouble with this equipment, please contact the manufacturer at the address given in this manual. The telephone company may ask that you disconnect this equipment from the network until the problem has been corrected or until you are sure that the equipment in is not malfunctioning.

DECLARATION of CONFORMITY

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installa- tion. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful inter-

71

Image 71
Contents ISA Plug n Play Voice/Fax Modem Table of Contents Contacting Actiontec Customer Support IntroductionBefore You Begin For Windows 95/98 InstallationFor Windows NT 4.0 Installation Hardware Installation Installing The ModemInstalling The Modem Connecting Devices Connecting Devices to the ModemConfiguring Windows Page Finish Configuring Windows 95 OSR2Page Page Configuring Windows Page Page Page Page Configuring Windows NT Page Page Page Page AT&F&C1&D2W2 Installing Communications SoftwareFax TIA/EIA-578 for Class 1 Fax Voice Init StringWindows 95/98 TroubleshootingMore Info Panel No Dialtone Error Common ProblemsCommunications Software Does Not Work COM Ports and Interrupts Appendix a Non Plug-N-Play InstallationsJumper Settings Jumpers Set To Plug-N-Play default setting Remove Installing In DOS and WindowsHardware and Driver Installation Page ATXn Appendix B AT Command SetRepeat Last Command Answer CommandCarrier Control Result CodesLast number dialed DnDialHook Control Echo CommandOnline Data Character Echo Command Request ID Information Monitor Speaker VolumeThis command sets speaker volume to low, medium, or high Modulation Handshake This command turns the speaker on or offResult Code Control Return On-line to Data ModeSelect Pulse Dialing Result Code Option DCE Response FormatDial Tone Detect Extended Result CodesRecall Stored Profile Long space disconnect is always disabledBusy Tone Detect Long Space DisconnectData Carrier Detect DCD Control Auto RetrainThis modem always auto retrains DTR Control Load Factory SettingsLocal Flow Control Selection Auxiliary Relay optionPulse Dial Make-to-Break Ratio Selection Asynchronous Communications ModeThis Command is effective only for use in Japan Data Set Ready DSR Option This command selects DSR actionBelow is an example of a possible output This command is used to display the active profilesSSE \Bn Zn=x\An Modem Port Flow Control Adjust Bits/s Rate Control\Kn \Nn Error Control Mode Selection = 0, 1, 2, 3, 4, 5 \Xn XON/XOFF Pass Through \Tn Inactivity Timer\Vn Protocol Result Code View Numbers in Blacklist Enable/Disable Data CompressionData Calling Tone Line-to-Line Loopback AT Commands for Testing and DebuggingSelf-Test Commands Write to/Read from DSP RegisterATI11 Type Registers ReferenceRange −127, Ascii decimal Default Line feed Units Range 0−255 Default UnitsringsRange 0−255 Default UnitsASCII Range −127, Ascii decimal Default Carriage return UnitsComma Dial Modifier Time Range −32 Default Backspace UnitsRange Default Unitsseconds Connection Completion Time-OutS14 General Bit Mapped Options Status S10S11 Dtmf Dialing Speed S12 Escape Guard TimeS22 S24 Timer to Control Sleep ModeS21 S33 S28 Modulation Enable/DisableS30 Inactivity Timer S32Connection S37 Dial Line Rate defaultS38 56K Dial Line Rate default S36S48 Lapm Error Control and Feature Negotiation default S42 Auto Rate default 1, rangeS43 Auto Mode default 1, range S92 S89 Timer to Control Sleep ModeS90 S91No Carrier S109K56flex and V.90 Selection defaultResult Code Declaration of Conformity Appendix B Communications RegulationsCanadian Department of Communications Cdoc