Actiontec electronic V.90 ISA user manual Zn=x, An, Bn

Page 51

&Zn=x

Store Telephone Number

This command is used to store up to four dialing strings in the modem’s nonvolatile memory for later dialing. The format for the command is &Zn = ”stored number” where n is the location 0?3 to which the number should be written. The dial string may contain up to 40 characters. The ATDS = n command dials using the string stored in location n.

Result Codes:

 

OK

n = 0, 1, 2, 3

 

 

 

 

 

 

ERROR

Otherwise

 

 

 

 

 

\An

Select Maximum MNP Block Size

The modem will operate an MNP error corrected link using a maximum block size controlled by the parameter supplied.

Command

Effect

 

 

\AO

64 characters

 

 

\A1

128 characters

 

 

\A2

192 characters

 

 

\A3

256 characters (Default)

 

 

Result Codes:

 

OK

n = 0, 1, 2, 3

 

 

 

 

 

 

ERROR

Otherwise

 

 

 

 

 

\Bn

Transmit Break to Remote

In non-error correction mode, the modem will transmit a break signal to the remote modem with a length in multiples of 100ms according to parameter specified. The command works in conjunction with the \K command.

 

Command

Effect

 

 

 

 

\B1-\B9

Break length in 100ms units. (Default = 3.) (Non-error

 

corrected mode only.)

 

 

 

 

 

Result Codes:

 

 

 

 

 

OK

If connected in data modem mode.

 

 

 

 

NO CARRIER

If not connected or connected in fax modem mode.

 

 

 

51

Image 51
Contents ISA Plug n Play Voice/Fax Modem Table of Contents Contacting Actiontec Customer Support IntroductionBefore You Begin For Windows 95/98 InstallationFor Windows NT 4.0 Installation Hardware Installation Installing The ModemInstalling The Modem Connecting Devices Connecting Devices to the ModemConfiguring Windows Page Finish Configuring Windows 95 OSR2Page Page Configuring Windows Page Page Page Page Configuring Windows NT Page Page Page Page AT&F&C1&D2W2 Installing Communications SoftwareFax TIA/EIA-578 for Class 1 Fax Voice Init StringWindows 95/98 TroubleshootingMore Info Panel No Dialtone Error Common ProblemsCommunications Software Does Not Work COM Ports and Interrupts Appendix a Non Plug-N-Play InstallationsJumper Settings Jumpers Set To Plug-N-Play default setting Installing In DOS and Windows Hardware and Driver InstallationRemove Page ATXn Appendix B AT Command SetRepeat Last Command Answer CommandCarrier Control Result CodesLast number dialed DnDialEcho Command Online Data Character Echo CommandHook Control Monitor Speaker Volume This command sets speaker volume to low, medium, or highRequest ID Information Modulation Handshake This command turns the speaker on or offReturn On-line to Data Mode Select Pulse DialingResult Code Control Result Code Option DCE Response FormatDial Tone Detect Extended Result CodesRecall Stored Profile Long space disconnect is always disabledBusy Tone Detect Long Space DisconnectAuto Retrain This modem always auto retrainsData Carrier Detect DCD Control DTR Control Load Factory SettingsLocal Flow Control Selection Auxiliary Relay optionAsynchronous Communications Mode This Command is effective only for use in JapanPulse Dial Make-to-Break Ratio Selection Data Set Ready DSR Option This command selects DSR actionBelow is an example of a possible output This command is used to display the active profilesSSE Zn=x \An\Bn Modem Port Flow Control Adjust Bits/s Rate Control\Kn \Nn Error Control Mode Selection = 0, 1, 2, 3, 4, 5 \Tn Inactivity Timer \Vn Protocol Result Code\Xn XON/XOFF Pass Through Enable/Disable Data Compression Data Calling ToneView Numbers in Blacklist Line-to-Line Loopback AT Commands for Testing and DebuggingSelf-Test Commands Write to/Read from DSP RegisterATI11 Type Registers ReferenceRange −127, Ascii decimal Default Line feed Units Range 0−255 Default UnitsringsRange 0−255 Default UnitsASCII Range −127, Ascii decimal Default Carriage return UnitsComma Dial Modifier Time Range −32 Default Backspace UnitsRange Default Unitsseconds Connection Completion Time-OutS14 General Bit Mapped Options Status S10S11 Dtmf Dialing Speed S12 Escape Guard TimeS24 Timer to Control Sleep Mode S21S22 S33 S28 Modulation Enable/DisableS30 Inactivity Timer S32Connection S37 Dial Line Rate defaultS38 56K Dial Line Rate default S36S42 Auto Rate default 1, range S43 Auto Mode default 1, rangeS48 Lapm Error Control and Feature Negotiation default S92 S89 Timer to Control Sleep ModeS90 S91No Carrier S109K56flex and V.90 Selection defaultResult Code Declaration of Conformity Appendix B Communications RegulationsCanadian Department of Communications Cdoc