Airlink101 AR695W manual AP Mode, Remote AP MAC, Scanned AP’s MAC, Scan AP

Page 50

Before you set up WDS bridging:

1)Make sure your wireless computer can associate with individual router/AP.

2)Configure the same channel for every router/AP.

3)Configure a unique different SSID for every router/AP in order to distinguish each unit on your wireless LAN.

4)Configure a static IP address for every router/AP. Make sure all IP addresses are based on the same subnet mask, and out of your DCHP client range.

Parameters

Description

 

 

 

AP Mode

AP Only: WDS function is disabled.

 

WDS Only: The router is functioning as a bridge to connect

 

with other WDS enabled AP/Router. Wireless client is not able

 

to connect to the router at WDS Only mode.

 

Hybrid: The router is functioning as a bridge as well as an AP

 

that allows wireless client association at the same time. (Note:

 

the data throughput is halved with Hybrid mode.)

Remote AP MAC

Enter the MAC address of other WDS enabled AP/Router into

 

MAC 1 ~ MAC4. This feature allows you to bridge up to 4

 

AR695W routers. It is suggested to use “Copy to” function to

 

avoid any typo.

Scanned AP’s MAC

Click on the drop-down menu to select a AP you wish to bridge

 

to, select a number from the drop-down menu of Remote AP

 

MAC and click Copy to, the MAC address will be automatically

 

filled into the corresponding MAC address field above.

Scan AP

Click Scan AP to find the available wireless Router/AP that you

 

wish to bridge. If the wireless router/AP is not showing in the list,

 

it may be out of range, and you need to move it closer in order

 

to build the bridge connection.

After you finished all settings, click Save to save the settings and click Reboot. The change will take effect after rebooting the router.

46

Image 50
Contents Wireless N 300 Gigabit Green Router Copyright Table of Contents Status Introduction and safety information Product InformationPackage Contents Familiar with your new Gigabit Router Front PanelBack Panel Configure the Router Connect the Router to your networkPage Configure the Router with EZ Setup Wizard Select your language and click Next Click on Wizard Page Page Cable Dynamic IP Example username@sbcglobal.net Page Page Configure the Router with Web Configuration Utility Page Page For Cable Users Dynamic IP Address Click on Clone MAC Example username@sbcglobal.net Page Page Connect to Router Wirelessly Page Advanced Configuration Page Basic Setting WAN Type Primary SetupLAN IP Address Virtual ComputersPage Static IP Address Dynamic IP AddressRenew IP Forever Host NameWAN’s MAC Address Dynamic IP Address with Road Runner Session Management PasswordLogin Server AccountPPP Over Ethernet PPPoE PPPoE Service Name Assigned IP AddressMy IP Address IP ModePptp Password My Subnet MaskL2TP Password L2TP AccountLocal IP EnableGlobal IP Lease Time Dhcp ServerDhcp Server IP Pool Starting/Ending AddressGateway Primary DNS/Secondary DNSPrimary WINS/Secondary Wins Client ListWireless Ssid Broadcast Wireless ModeWireless Client List ChannelConfiguring Security WEP Configuring Security WPA-PSK / WPA2-PSKConfiguring Security 802.1x and Radius Configuring Security WPA / WPA2 3.1 WDS Scanned AP’s MAC AP ModeRemote AP MAC Scan APWPS Easy Setup Button Page Page Select Enable or Disable WPS function WPS State WPS StatusNew Password Change PasswordOld Password ReconfirmForwarding Rules Well known servicesService Ports Virtual ServerNext / Previous ProtocolSchedule Rule# Trigger Special ApplicationsPopular applications Incoming PortsMiscellaneous IP Address of DMZ HostUPnP Super DMZ IP PassthroughNon-standard FTP Port Xbox SupportSecurity Setting Packet FilteringSource IP Outbound/InboundPacket Filter Destination IPPort Inbound FilterDomain Blocking Recorded in log file URL Blocking URL BlockingInternet Access Control Page Association Control MAC Access ControlMAC Address Control Previous / Next Dhcp ClientsMAC Address Add MAC Address Group MAC Access ControlGroup MAC Access Control Interface Interface Access ControlInterface Access Control Schedule Rule DenyDoS Attack Detection SPI ModeDiscard Ping from WAN side VPN Pptp Pass-ThroughSystem Time Advanced SettingSelect Set Date and Time using PC’s Date and Time Select Get Date and Time by NTP ProtocolTime Server System TimeSync Now Time ZoneEmail Alert System LogIP Address of Syslog Server Send Mail NowUsername Email AddressesEmail Subject Log TypeProvider Password / KeyDynamic DNS Provider WebsiteQoS Rule QoS ControlQoS Priority Remote IP AddressPorts Snmp Routing AR695W Dynamic RoutingSubnet Mask Static RoutingDestination HopRule# Schedule RuleSchedule Rule NameStart Time/End Time hhmm Name of Rule#Week Day Toolbox View Log Firmware Upgrade Backup Setting Reset to DefaultReboot Domain Name or IP Address for Ping Test Status Wireless Status System StatusStatistics Information NAT StatusHardware Specification Technical Support