Airlink101 AR695W manual Port, Inbound Filter

Page 64

Port

Please input the port number here. You can define a single port

 

(80) or a range of ports (1000-1999). Add prefix "T" or "U" to

 

specify TCP or UDP protocol, for example, T80, U53,

 

U2000-2999. No prefix indicates both TCP and UDP are defined.

 

Leaving this field blank indicates all ports.

Enable

Check/uncheck Enable to enable/disable each Packet Filtering

 

rule.

Schedule Rule#

Enter a Schedule Rule number to activate the filtering rule only

 

within the desired time frame. Please refer to 3.4.7 Schedule

 

Rule for detailed setting instructions. Set 0 to let the filtering rule

 

always take effect.

Inbound Filter

Click Inbound Filter button to go to Inbound Packet Filter settings.

 

 

Click on Save after you finished all settings.

60

Image 64
Contents Wireless N 300 Gigabit Green Router Copyright Table of Contents Status Introduction and safety information Product InformationPackage Contents Familiar with your new Gigabit Router Front PanelBack Panel Configure the Router Connect the Router to your networkPage Configure the Router with EZ Setup Wizard Select your language and click Next Click on Wizard Page Page Cable Dynamic IP Example username@sbcglobal.net Page Page Configure the Router with Web Configuration Utility Page Page For Cable Users Dynamic IP Address Click on Clone MAC Example username@sbcglobal.net Page Page Connect to Router Wirelessly Page Advanced Configuration Page Basic Setting Primary Setup LAN IP AddressWAN Type Virtual ComputersPage Static IP Address Dynamic IP AddressWAN’s MAC Address Host NameRenew IP Forever Password Login ServerDynamic IP Address with Road Runner Session Management AccountPPP Over Ethernet PPPoE PPPoE Service Name Assigned IP AddressIP Mode Pptp PasswordMy IP Address My Subnet MaskL2TP Password L2TP AccountGlobal IP EnableLocal IP Dhcp Server Dhcp ServerLease Time IP Pool Starting/Ending AddressPrimary DNS/Secondary DNS Primary WINS/Secondary WinsGateway Client ListWireless Wireless Mode Wireless Client ListSsid Broadcast ChannelConfiguring Security WEP Configuring Security WPA-PSK / WPA2-PSKConfiguring Security 802.1x and Radius Configuring Security WPA / WPA2 3.1 WDS AP Mode Remote AP MACScanned AP’s MAC Scan APWPS Easy Setup Button Page Page Select Enable or Disable WPS function WPS State WPS StatusChange Password Old PasswordNew Password ReconfirmWell known services Service PortsForwarding Rules Virtual ServerSchedule Rule# ProtocolNext / Previous Special Applications Popular applicationsTrigger Incoming PortsMiscellaneous IP Address of DMZ HostSuper DMZ IP Passthrough Non-standard FTP PortUPnP Xbox SupportSecurity Setting Packet FilteringOutbound/Inbound Packet FilterSource IP Destination IPPort Inbound FilterDomain Blocking Recorded in log file URL Blocking URL BlockingInternet Access Control Page MAC Address Control MAC Access ControlAssociation Control MAC Address Dhcp ClientsPrevious / Next Group MAC Access Control Group MAC Access ControlAdd MAC Address Interface Access Control Interface Access ControlInterface Schedule Rule DenySPI Mode Discard Ping from WAN sideDoS Attack Detection VPN Pptp Pass-ThroughAdvanced Setting Select Set Date and Time using PC’s Date and TimeSystem Time Select Get Date and Time by NTP ProtocolSystem Time Sync NowTime Server Time ZoneSystem Log IP Address of Syslog ServerEmail Alert Send Mail NowEmail Addresses Email SubjectUsername Log TypePassword / Key Dynamic DNSProvider Provider WebsiteQoS Rule QoS ControlPorts Remote IP AddressQoS Priority Snmp Routing AR695W Dynamic RoutingStatic Routing DestinationSubnet Mask HopSchedule Rule ScheduleRule# Rule NameWeek Day Name of Rule#Start Time/End Time hhmm Toolbox View Log Firmware Upgrade Backup Setting Reset to DefaultReboot Domain Name or IP Address for Ping Test Status Wireless Status System StatusStatistics Information NAT StatusHardware Specification Technical Support