Airlink101 AR695W manual Change Password, Old Password, New Password, Reconfirm

Page 56

3.1.4 Change Password

You can change the password required to log in to the Router’s web configuration utility. The default password is “admin”. It is suggested to change the administrator’s default password as soon as you start to use the Router, and store it in a safe place. The password consists of 0 to 9 alphanumeric characters, and is case sensitive

Parameters

Description

 

 

Old Password

Enter the current password of the router.

New Password

Enter the new password.

Reconfirm

Enter the new password again for verification purposes.

 

Note: If you forget your password, you’ll have to reset the router

 

to the factory default (the default password is ‘admin’) by pushing

 

and holding the WLAN/Reset button on the front panel of the

 

router for 6 seconds.

 

 

Click Save after you finished all settings.

52

Image 56
Contents Wireless N 300 Gigabit Green Router Copyright Table of Contents Status Introduction and safety information Product InformationPackage Contents Familiar with your new Gigabit Router Front PanelBack Panel Configure the Router Connect the Router to your networkPage Configure the Router with EZ Setup Wizard Select your language and click Next Click on Wizard Page Page Cable Dynamic IP Example username@sbcglobal.net Page Page Configure the Router with Web Configuration Utility Page Page For Cable Users Dynamic IP Address Click on Clone MAC Example username@sbcglobal.net Page Page Connect to Router Wirelessly Page Advanced Configuration Page Basic Setting Primary Setup LAN IP AddressWAN Type Virtual ComputersPage Static IP Address Dynamic IP AddressRenew IP Forever Host NameWAN’s MAC Address Password Login ServerDynamic IP Address with Road Runner Session Management AccountPPP Over Ethernet PPPoE PPPoE Service Name Assigned IP AddressIP Mode Pptp PasswordMy IP Address My Subnet MaskL2TP Password L2TP AccountLocal IP EnableGlobal IP Dhcp Server Dhcp ServerLease Time IP Pool Starting/Ending AddressPrimary DNS/Secondary DNS Primary WINS/Secondary WinsGateway Client ListWireless Wireless Mode Wireless Client ListSsid Broadcast ChannelConfiguring Security WEP Configuring Security WPA-PSK / WPA2-PSKConfiguring Security 802.1x and Radius Configuring Security WPA / WPA2 3.1 WDS AP Mode Remote AP MACScanned AP’s MAC Scan APWPS Easy Setup Button Page Page Select Enable or Disable WPS function WPS State WPS StatusChange Password Old PasswordNew Password ReconfirmWell known services Service PortsForwarding Rules Virtual ServerNext / Previous ProtocolSchedule Rule# Special Applications Popular applicationsTrigger Incoming PortsMiscellaneous IP Address of DMZ HostSuper DMZ IP Passthrough Non-standard FTP PortUPnP Xbox SupportSecurity Setting Packet FilteringOutbound/Inbound Packet FilterSource IP Destination IPPort Inbound FilterDomain Blocking Recorded in log file URL Blocking URL BlockingInternet Access Control Page Association Control MAC Access ControlMAC Address Control Previous / Next Dhcp ClientsMAC Address Add MAC Address Group MAC Access ControlGroup MAC Access Control Interface Interface Access ControlInterface Access Control Schedule Rule DenySPI Mode Discard Ping from WAN sideDoS Attack Detection VPN Pptp Pass-ThroughAdvanced Setting Select Set Date and Time using PC’s Date and TimeSystem Time Select Get Date and Time by NTP ProtocolSystem Time Sync NowTime Server Time ZoneSystem Log IP Address of Syslog ServerEmail Alert Send Mail NowEmail Addresses Email SubjectUsername Log TypePassword / Key Dynamic DNSProvider Provider WebsiteQoS Rule QoS ControlQoS Priority Remote IP AddressPorts Snmp Routing AR695W Dynamic RoutingStatic Routing DestinationSubnet Mask HopSchedule Rule ScheduleRule# Rule NameStart Time/End Time hhmm Name of Rule#Week Day Toolbox View Log Firmware Upgrade Backup Setting Reset to DefaultReboot Domain Name or IP Address for Ping Test Status Wireless Status System StatusStatistics Information NAT StatusHardware Specification Technical Support