ADTRAN IPR-S1000 manual Document objectives, Audience, Document organization, Document conventions

Page 6

Installing the IPR-S1000

INSTALLING THE IPR-S1000

I About the installation section

1. Document objectives

This installation section explains the preparation for installation as well as the configuration procedures for the IPR-S1000. It also gives you information concerning the IPR-S1000 start up and troubleshooting.

2. Audience

To use this publication, it is recommended to be familiar with cabling, electronic circuitry and wiring practices.

3. Document organization

This installation section provides easy-to-use instructions and explanations. The chapters are organized as follows:

• Preparing for installation

It is a preparatory chapter that describes safety recommendations, material verification and site requirements. It also enumerates the procedures you should perform before the actual installation.

• Installing the IPR-S1000

It provides instructions for connecting the cables and configuring hyper-terminal. It also explains the initial configuration process.

4. Document conventions

The document uses the following conventions:

Caution Means reader be careful. In this situation, you might do something that could result in equipment damage or loss of data.

Warning Means danger. You are in a situation that could cause bodily injury. Before working on an equipment, be aware of the hazards involved with electrical circuitry .

Note: Means reader take note. Notes contain helpful suggestions.

1

Image 6

Contents USER’S Guide Acknowledgements Page Installing the IPR-S1000 Telnet interface Document organization Document objectivesAudience Document conventionsObtaining technical assistance Safety recommendationsTerms and abbreviations Material verificationEnsure your safety Installation checklist Site requirementsProtect the equipment Connecting to the satellite antenna Connecting the cablesConnecting to the Ethernet network Connecting the power cordMaking an initial configuration of the IPR-S1000 Starting up the IPR-S1000Making the connection IP address FEC LNB Power Overview Basic screensExample 12.379 27500K + Auto 11.0dB Example Ethernet 192.168.43.48/24 Menu Set configMain menu Example 1002 0x3ea 11KP10MB11C 11D MAC filteringDVB Example High Band Low band Universal LNBExample Frequency 12.3790000GHz Example Bauds Kbauds Example FEC Auto 1/2 2/3 3/4 4/5 5/6 6/7 7/8 8/9Example Polarization Vert./RHCP/14v Horiz./LHCP/18v Example ModulationPSK 16 QAM Example LNB Power Off Example DVB IP address 172.022.000.051/24Example Start MPE PID 1002 0x3ea Example Stop MPE PID 1002 0x3ea 3032 0xbd8 Example Processing CRC MPE YesExample MAC address filtering on 6 bytes Ethernet IP address Media typeEthernet Example IP address 192.168.043.048/24 13. IPExample Unicast forwarding Routing Bridging Example Broadcast bridging YesNew network address 000.000.000.000/00 Example Mcast forwarding Accept src addrMcast forwarding Yes routing Yes bridging Multicast On/OffDNS 1 DNS 2 Example Bridging traffic Bridge only Analyse & bridgeExample Icmp redirect Yes Example Delete all routes? CancelOk Example Def. none Edit DeleteProfiles Save Fact. profile Tftp load Tftp save Example Profile nameProfiles Factory profile Startup Load Example Tftp Server addrNew write password New read passwordReceipt code Active MPE PID 1002 0x3 ea Menu View Config12.379 27500K + Auto 5.6dB DVB MAC address 00D0B5XXXXXXMonitoring Example Really reboot? ? Cancel Uncor. packets Reset ?Temperature 35.3 C Unlock Vber 1.3 EFirmwareQPSK S1000-3.01.41a VersionMain Configuring the IPR-S1000 Configuring the IPR-S1000 Profiles and passwords Load Management System Reboot DVB Field, enter the low band local oscillator Interface Tuner Ethernet Definition This module allows you to manage IP parameters Forwarding User Interface Fixed Key Conditionnal Access Snmp Snmp traps Syslog Bandwidth IP Crypt Firewall Mac addresses NAT Drop-down menu, select active to start NAT PPP Configuring the IPR-S1000 Configuring the IPR-S1000 Pptp Configuring the IPR-S1000 Udlr Drop-down menu, select active to start Udlr Tools SpectrumTS Dump Configuring the IPR-S1000 DVB Dump IP Dump Configuring the IPR-S1000 Ethernet Ping You are trying to reach is actually operating TracerouteBlank field, enter the hostname or IP address Network statistics III The Telnet interface ShellCommands Example + name of the profileBye Auth AuthenticationAbort Delete + name of the profile to be removedGet section.attribut GetdefaultExit HelpLoad + name of the profile LastprofileList LoadfactoryQuit Ppp Point to point protocol Acts on PPP processPptp point to point tuneling protocol Rename + formername newnameTraceroute + IP address or «Host» name TftploadTftpsave TsdumpDvb Digital Video Broadcasting Get Displays NAT information System System action Traceroute + IP address or «host» name Sections and attributes Bandwidth.sizeDvb.bauds Dvb.fec Dvb.crcmpeDvb.dvbipaddr Dvb.freqDvb.relaxbauds Dvb.mpepids List of MPE PIDs Dvb.mtuDvb.polar Dvb.scanfreqIp.mcastaddr Ip.keepforusIp.macaddr Ip.multicastNat.autoifaceiface Ppp.passwordNat.autoifaceactive Nat.dynactivePptp.password Contains the password Pptp.pns Pptp.connecttimerPptp.keepalivetimer Pptp.retrytimerIV. The Snmp interface Glossary CRC DRO Iana ISO MPE Pstn RIP Vsat IPricotSA