ADTRAN IPR-S1000 manual Site requirements, Installation checklist, Protect the equipment

Page 9

Installing the IPR-S1000

Protect the equipment

1)Never assume that electrical power is disconnected. Do check it first.

2)Do a previous check-up of any potential source of danger within your work environment (wet floor, visible electrical cable...).

3)Always disconnect AC power cable during the installation when moving the equipment.

3. Site requirements

To assure normal operation and avoid unnecessary maintenance, it is recommended to prepare your site before installation.

Planning a proper location for the IPR-S1000

1)Place the IPR-S1000 into the desired location. The unit is designed to be sitting vertically on a plane and clean surface.

2)Keep the product safe from heat, dust and moisture.

3)Make sure the site maintains an ambient temperature of 5° to 45°C.

4. Installation checklist

To assist you with your installation and to provide a historical record of what was done and by whom, fill in the following IPR-S1000 installation checklist.

Installation Checklist

	Task	Verified
	Task	by
		by

Date the IPR-S1000 received

The IPR-S1000 and accessories unpacked

Types and numbers of interfaces verified

Safety recommendations and guidelines reviewed

Site requirements verified

Date

4

Image 9

Contents USER’S Guide Acknowledgements Page Installing the IPR-S1000 Telnet interface Audience Document objectivesDocument organization Document conventionsTerms and abbreviations Safety recommendationsObtaining technical assistance Material verificationEnsure your safety Installation checklist Site requirementsProtect the equipment Connecting to the Ethernet network Connecting the cablesConnecting to the satellite antenna Connecting the power cordMaking an initial configuration of the IPR-S1000 Starting up the IPR-S1000Making the connection IP address FEC LNB Power Overview Basic screensExample 12.379 27500K + Auto 11.0dB Main menu Menu Set configExample Ethernet 192.168.43.48/24 Example 1002 0x3ea 11KP10MB11C 11D MAC filteringDVB Example High Band Low band Universal LNBExample Frequency 12.3790000GHz Example FEC Auto 1/2 2/3 3/4 4/5 5/6 6/7 7/8 8/9 Example Bauds KbaudsExample Polarization Vert./RHCP/14v Horiz./LHCP/18v Example ModulationPSK 16 QAM Example LNB Power Off Example DVB IP address 172.022.000.051/24Example Start MPE PID 1002 0x3ea Example Processing CRC MPE Yes Example Stop MPE PID 1002 0x3ea 3032 0xbd8Example MAC address filtering on 6 bytes Ethernet IP address Media typeEthernet 13. IP Example IP address 192.168.043.048/24Example Broadcast bridging Yes Example Unicast forwarding Routing BridgingMcast forwarding Yes routing Yes bridging Example Mcast forwarding Accept src addrNew network address 000.000.000.000/00 Multicast On/OffDNS 1 DNS 2 Example Bridging traffic Bridge only Analyse & bridgeExample Icmp redirect Yes Example Def. none Edit Delete Example Delete all routes? CancelOkProfiles Save Fact. profile Tftp load Tftp save Example Profile nameProfiles Example Tftp Server addr Factory profile Startup LoadNew write password New read passwordReceipt code 12.379 27500K + Auto 5.6dB Menu View ConfigActive MPE PID 1002 0x3 ea DVB MAC address 00D0B5XXXXXXMonitoring Temperature 35.3 C Uncor. packets Reset ?Example Really reboot? ? Cancel Unlock Vber 1.3 EVersion FirmwareQPSK S1000-3.01.41aMain Configuring the IPR-S1000 Configuring the IPR-S1000 Profiles and passwords Load Management System Reboot DVB Field, enter the low band local oscillator Interface Tuner Ethernet Definition This module allows you to manage IP parameters Forwarding User Interface Fixed Key Conditionnal Access Snmp Snmp traps Syslog Bandwidth IP Crypt Firewall Mac addresses NAT Drop-down menu, select active to start NAT PPP Configuring the IPR-S1000 Configuring the IPR-S1000 Pptp Configuring the IPR-S1000 Udlr Drop-down menu, select active to start Udlr Spectrum ToolsTS Dump Configuring the IPR-S1000 DVB Dump IP Dump Configuring the IPR-S1000 Ethernet Ping Traceroute You are trying to reach is actually operatingBlank field, enter the hostname or IP address Network statistics Shell III The Telnet interfaceExample + name of the profile CommandsAbort Auth AuthenticationBye Delete + name of the profile to be removedExit GetdefaultGet section.attribut HelpList LastprofileLoad + name of the profile LoadfactoryPptp point to point tuneling protocol Ppp Point to point protocol Acts on PPP processQuit Rename + formername newnameTftpsave TftploadTraceroute + IP address or «Host» name TsdumpDvb Digital Video Broadcasting Get Displays NAT information System System action Traceroute + IP address or «host» name Sections and attributes Bandwidth.sizeDvb.bauds Dvb.dvbipaddr Dvb.crcmpeDvb.fec Dvb.freqDvb.polar Dvb.mpepids List of MPE PIDs Dvb.mtuDvb.relaxbauds Dvb.scanfreqIp.macaddr Ip.keepforusIp.mcastaddr Ip.multicastNat.autoifaceactive Ppp.passwordNat.autoifaceiface Nat.dynactivePptp.keepalivetimer Pptp.connecttimerPptp.password Contains the password Pptp.pns Pptp.retrytimerIV. The Snmp interface Glossary CRC DRO Iana ISO MPE Pstn RIP Vsat IPricotSA