ADTRAN T1-FT1 Viewing Display Only Data Fields, To Exit Any Menu Field Operation or Display

Page 41

Chapter 3. Operation

3.When the desired value is in the data field position, press ENTER to set the value.

The unit is set for the value shown in the data field and the cursor moves back to the submenu item position indicating the operation is complete.

4.Select another submenu field or use the CANCEL key to return to the submenu.

CANCEL is available any time during the operation. If used prior to pressing ENTER after making a data change, the original data value is restored and the cursor returns to the submenu field.

Viewing Display Only Data Fields

An example of a Display Only data field is found by selecting the following menu choices.

1.Select STATUS from the main menu.

2.Select 2)CURR ERR/ALM from the submenu.

LOSS OF SIGNAL INACTIVE/ACTIVE is displayed giving the

current state of the alarm.

To Exit Any Menu Field Operation or Display

Press the CANCEL key as many times as required to return to the desired menu level.

61200060L1-1

TSU User Manual

3-5

Image 41
Contents Part Number 1200060L1 T1-FT1 Data/Channel Service UnitPage Iii REN/SOC FIC Usoc ServicePage Important Safety Instructions Warranty and Customer Service Viii Table of Contents Operation Index Index-1 Table of Contents Xii List of Figures Figure A-1 TSU Complete Menu DiagramList of Figures List of Tables List of Tables T1/FT1 Overview T1 Service OfferingsIntroduction Fractional T1 Functional Description TSU OverviewControl FunctionTest Jacks Interfaces FeaturesNx56/64 Serial Interface Network InterfaceControl Port Input Chain Por t OutputFront Panel Three Methods of ControlAdtran PC Program SnmpNetwork Timed TSU Clock SourcesDTE Clock Source DTE TimedInternal Clock Source Internal TimingLoopback Tests TSU TestingSelf Tests TSU Network LoopbacksAll Ones DTE Interface Loopbacks511 ApplicationUNPACK, INSPECT, Power Connection InstallationPower Connection Adtran Shipments IncludeNetwork WiringNetwork Pin Connection PIN Name DescriptionControl PIN Connection Name Description Control In/ChainControl In/Chain In Pin Connection Chain OUT PIN Connection Chain OutChain Out Pin Connection Primary V.35 Pin Connection Nx56k/64k DTENx 56k/64/ DTE PIN Connection PIN Ccitt DescriptionSelf Test Power UP Testing and InitializationMethods of Operation OperationFront Panel Operation CancelALM LCD WindowO N F I G General Menu OperationT a T U S Code Z S Setting the Data FieldE T W O R K N N I T To Exit Any Menu Field Operation or Display Viewing Display Only Data FieldsFour Opening Menus Menu StructureFour Opening Menu Functions Util Fact RestoreTIME/DATE Software VersionStatus Menu Menu OperationNI Perf RPTS, Submenu of 1Status 1RESET Perf CntrsData Values Minutes Hours15MIN / 24HR Curr ERR/ALM Submenu of 1Status Alarm InvestigatedState Active/Inactive ERR/ALM Hist Submenu of 1Status Clear HistoryComplete Configuration Menu ConfigurationO R M a T Code Z S Network NI Submenu of 2 ConfigXmit PRM Cntrl Port O N T R O L P O R T Alarm SUNIT, Submenu of 2 Config Data Rate AlarmsRate 56/64 PORT, Submenu of Config# of Chan Normal Mode of Operation1Time/Date, Submenu of 3Util UtilKeystroke Summary for Editing Time/Date M E 0 5 0 7 0 T E 0 8 / 0 5 / 93Reinit Unit, Submenu of 3Util 2Software Rev, Submenu of 3Util4Address,Submenu of 3Util 5Fact Restore, Submenu of 3UtilE I N I T D D R E S S 0 0 Complete Test Menu Test1Network Tests, Submenu of 4Test Loopback or 3PATTERN 2Run Selftest, Submenu of 4Test R 5 1 1 Error S 5 1 1 Error S = 53Port Tests submenu of 4Test S T E M S E L F T E S TT E L O O P B C K O F F Operation Far End Looped Back Test Testing ExampleN I T O R 3 U T I L Network Interface TestE T W O R K T E S T S U N S E L F T E S T Press Enter to activate a Remote Payload Loopback Testing Example Appendix a TSU Complete Menu Figure A-1. TSU Complete Menu DiagramAppendix A. TSU Complete Menu DTE Rate = 56K Appendix B DTE Data Rate ChartDTE Data Rate vs DS0s N # of DS0s N Appendix B. DTE Data Rate Chart Numerics IndexIndex Repair and Return Presales Inquiries and Applications SupportPost-Sale Support