ADTRAN T1-FT1 user manual Application, 511

Page 30

Chapter 1. Introduction

511

The 511 pattern is generated and checked by the Nx56k/64k serial interface. It only appears in the DS0s assigned to the Nx56k/64k port. When used in conjunction with the payload loopback at the far end as previously described, an end to end integrity check can be made on the DTE ports.

1 in 8

The 1:8 pattern is used similarly to the 3:24. Each channel of the T1 has only one bit set.

Application

Using the V.35 DTE interface, a bridge or router can be interfaced to the network. The bandwidth used is programmable at Nx56 or Nx64 data rates for T1 or FT1 service. The bandwidth can be selected as contiguous or alternate. See Figure 1-9.

Bridge Router	TSU	TSU	NX56/64	Bridge Router
NX56/64
V.35		(Public T1)	V.35

Figure 1-9. Simple Bridge Application on a T1 or FT1 Circuit

1-14

TSU User Manual

61200060L1-1

Image 30

Contents T1-FT1 Data/Channel Service Unit Part Number 1200060L1Page Iii Service REN/SOC FIC UsocPage Important Safety Instructions Warranty and Customer Service Viii Table of Contents Operation Index Index-1 Table of Contents Xii Figure A-1 TSU Complete Menu Diagram List of FiguresList of Figures List of Tables List of Tables T1 Service Offerings IntroductionT1/FT1 Overview Fractional T1 TSU Overview Functional DescriptionFunction Test JacksControl Features InterfacesControl Port Input Network InterfaceNx56/64 Serial Interface Chain Por t OutputAdtran PC Program Three Methods of ControlFront Panel SnmpTSU Clock Sources Network TimedDTE Timed DTE Clock SourceInternal Timing Internal Clock Source TSU Testing Self Tests Loopback Tests Network Loopbacks TSUDTE Interface Loopbacks All OnesApplication 511Power Connection InstallationUNPACK, INSPECT, Power Connection Adtran Shipments IncludeNetwork Pin Connection WiringNetwork PIN Name DescriptionControl In/Chain Control In/Chain In Pin ConnectionControl PIN Connection Name Description Chain Out Chain Out Pin ConnectionChain OUT PIN Connection Nx 56k/64/ DTE PIN Connection Nx56k/64k DTEPrimary V.35 Pin Connection PIN Ccitt DescriptionPower UP Testing and Initialization Self TestOperation Methods of OperationALM CancelFront Panel Operation LCD WindowGeneral Menu Operation T a T U SO N F I G Setting the Data Field E T W O R K N N I TCode Z S Viewing Display Only Data Fields To Exit Any Menu Field Operation or DisplayMenu Structure Four Opening MenusFour Opening Menu Functions TIME/DATE Fact RestoreUtil Software VersionMenu Operation Status Menu1RESET Perf Cntrs NI Perf RPTS, Submenu of 1StatusMinutes Hours 15MIN / 24HRData Values Alarm Investigated State Active/InactiveCurr ERR/ALM Submenu of 1Status Clear History ERR/ALM Hist Submenu of 1StatusConfiguration Complete Configuration MenuNetwork NI Submenu of 2 Config O R M a T Code Z SXmit PRM O N T R O L P O R T Alarm S UNIT, Submenu of 2 ConfigCntrl Port Alarms Data RatePORT, Submenu of Config Rate 56/64Normal Mode of Operation # of ChanUtil 1Time/Date, Submenu of 3UtilM E 0 5 0 7 0 T E 0 8 / 0 5 / 9 Keystroke Summary for Editing Time/Date2Software Rev, Submenu of 3Util 3Reinit Unit, Submenu of 3Util5Fact Restore, Submenu of 3Util E I N I T D D R E S S 0 04Address,Submenu of 3Util Test Complete Test Menu1Network Tests, Submenu of 4Test Loopback or 3PATTERN R 5 1 1 Error S 5 1 1 Error S = 5 2Run Selftest, Submenu of 4TestS T E M S E L F T E S T T E L O O P B C K O F F3Port Tests submenu of 4Test Operation N I T O R 3 U T I L Testing ExampleFar End Looped Back Test Network Interface TestE T W O R K T E S T S U N S E L F T E S T Press Enter to activate a Remote Payload Loopback Testing Example Figure A-1. TSU Complete Menu Diagram Appendix a TSU Complete MenuAppendix A. TSU Complete Menu Appendix B DTE Data Rate Chart DTE Data Rate vs DS0s N # of DS0s NDTE Rate = 56K Appendix B. DTE Data Rate Chart Index NumericsIndex Presales Inquiries and Applications Support Post-Sale SupportRepair and Return