ADTRAN T1-FT1 user manual O N T R O L P O R T Alarm S, UNIT, Submenu of 2 Config, Cntrl Port

Page 53

Chapter 3. Operation

2) UNIT, SUBMENU OF 2) CONFIG

The unit submenu is used to change control port and alarm options.

1.Follow standard operating procedures to access the Unit menu item.

2.With the cursor on 2)UNIT, press ENTER. The results display two submenu items.

1 ) C O N T R O L P O R T

2 ) A L A R M S

1) CNTRL PORT

Used to set the unit up as the Master or Slave on a chain of units, and whether to initialize a modem and the control port data rate.

POSITION

Determines if this TSU is at the head of a chain of units (directly connected to the modem or PC). The head of the chain is referred to as the Master Unit. Units down the chain are referred to as Slaves or a Slave Unit.

The setting of the position selection is necessary only when using a modem, in which case the head unit should be Master. For all other cases, select SLAVE. (The Master is in charge for control of the modem.)

Choices: MASTER; SLAVE

MODEM INIT

The TSU is capable of initializing a modem. This menu selection is used to effect this initialization and should be selected only when the choice above designates the TSU as the MASTER. Prior to modem initialization it should be physically connected to the TSU and the power turned on. At this point, an industry-standard AT command string is used to initialize the modem. The string is also used following future power-up sequences.

Choices: ENAB - Enable; DISA - Disable

61200060L1-1

TSU User Manual

3-17

Image 53
Contents Part Number 1200060L1 T1-FT1 Data/Channel Service UnitPage Iii REN/SOC FIC Usoc ServicePage Important Safety Instructions Warranty and Customer Service Viii Table of Contents Operation Index Index-1 Table of Contents Xii List of Figures Figure A-1 TSU Complete Menu DiagramList of Figures List of Tables List of Tables T1/FT1 Overview T1 Service OfferingsIntroduction Fractional T1 Functional Description TSU OverviewControl FunctionTest Jacks Interfaces FeaturesNx56/64 Serial Interface Network InterfaceControl Port Input Chain Por t OutputFront Panel Three Methods of ControlAdtran PC Program SnmpNetwork Timed TSU Clock SourcesDTE Clock Source DTE TimedInternal Clock Source Internal TimingLoopback Tests TSU TestingSelf Tests TSU Network LoopbacksAll Ones DTE Interface Loopbacks511 ApplicationUNPACK, INSPECT, Power Connection InstallationPower Connection Adtran Shipments IncludeNetwork WiringNetwork Pin Connection PIN Name DescriptionControl PIN Connection Name Description Control In/ChainControl In/Chain In Pin Connection Chain OUT PIN Connection Chain OutChain Out Pin Connection Primary V.35 Pin Connection Nx56k/64k DTENx 56k/64/ DTE PIN Connection PIN Ccitt DescriptionSelf Test Power UP Testing and InitializationMethods of Operation OperationFront Panel Operation CancelALM LCD WindowO N F I G General Menu OperationT a T U S Code Z S Setting the Data FieldE T W O R K N N I T To Exit Any Menu Field Operation or Display Viewing Display Only Data FieldsFour Opening Menus Menu StructureFour Opening Menu Functions Util Fact RestoreTIME/DATE Software VersionStatus Menu Menu OperationNI Perf RPTS, Submenu of 1Status 1RESET Perf CntrsData Values Minutes Hours15MIN / 24HR Curr ERR/ALM Submenu of 1Status Alarm InvestigatedState Active/Inactive ERR/ALM Hist Submenu of 1Status Clear HistoryComplete Configuration Menu ConfigurationO R M a T Code Z S Network NI Submenu of 2 ConfigXmit PRM Cntrl Port O N T R O L P O R T Alarm SUNIT, Submenu of 2 Config Data Rate AlarmsRate 56/64 PORT, Submenu of Config# of Chan Normal Mode of Operation1Time/Date, Submenu of 3Util UtilKeystroke Summary for Editing Time/Date M E 0 5 0 7 0 T E 0 8 / 0 5 / 93Reinit Unit, Submenu of 3Util 2Software Rev, Submenu of 3Util4Address,Submenu of 3Util 5Fact Restore, Submenu of 3UtilE I N I T D D R E S S 0 0 Complete Test Menu Test1Network Tests, Submenu of 4Test Loopback or 3PATTERN 2Run Selftest, Submenu of 4Test R 5 1 1 Error S 5 1 1 Error S = 53Port Tests submenu of 4Test S T E M S E L F T E S TT E L O O P B C K O F F Operation Far End Looped Back Test Testing ExampleN I T O R 3 U T I L Network Interface TestE T W O R K T E S T S U N S E L F T E S T Press Enter to activate a Remote Payload Loopback Testing Example Appendix a TSU Complete Menu Figure A-1. TSU Complete Menu DiagramAppendix A. TSU Complete Menu DTE Rate = 56K Appendix B DTE Data Rate ChartDTE Data Rate vs DS0s N # of DS0s N Appendix B. DTE Data Rate Chart Numerics IndexIndex Repair and Return Presales Inquiries and Applications SupportPost-Sale Support