ADTRAN T1-FT1 user manual Clear History, ERR/ALM Hist Submenu of 1Status

Page 49

Chapter 3. Operation

ERR/ALM Hist Submenu of 1)Status

The Error/Alarm History menu is used for viewing history of errors and alarms. If an alarm has occurred since the last CLEAR HISTORY selection, the menu will be ACTIVE. If the condition hasn't occured then the menu will be INACTIVE.

1.With the cursor on main menu item 1)STATUS.

2.Press ENTER. The first of three status submenu items display.

3.Press the down scroll key twice. The cursor is on

3)ERR/ALM HIST.

4.Press ENTER. The cursor is on the CLEAR HISTORY menu.

CLEAR HISTORY

5.Press ENTER. This results in clearing of all the ERROR/ ALARM HISTORIES that follow.

6.Use the up and down scroll keys to access the error and alarm conditions.

These conditions are the same as for the CURR ERR/ALM submenu except with these are history Alarm/Errors instead of current Alarm/Errors.

61200060L1-1

TSU User Manual

3-13

Image 49

Contents Part Number 1200060L1 T1-FT1 Data/Channel Service UnitPage Iii REN/SOC FIC Usoc ServicePage Important Safety Instructions Warranty and Customer Service Viii Table of Contents Operation Index Index-1 Table of Contents Xii List of Figures Figure A-1 TSU Complete Menu DiagramList of Figures List of Tables List of Tables Introduction T1 Service OfferingsT1/FT1 Overview Fractional T1 Functional Description TSU OverviewTest Jacks FunctionControl Interfaces FeaturesNx56/64 Serial Interface Network InterfaceControl Port Input Chain Por t OutputFront Panel Three Methods of ControlAdtran PC Program SnmpNetwork Timed TSU Clock SourcesDTE Clock Source DTE TimedInternal Clock Source Internal TimingSelf Tests TSU TestingLoopback Tests TSU Network LoopbacksAll Ones DTE Interface Loopbacks511 ApplicationUNPACK, INSPECT, Power Connection InstallationPower Connection Adtran Shipments IncludeNetwork WiringNetwork Pin Connection PIN Name DescriptionControl In/Chain In Pin Connection Control In/ChainControl PIN Connection Name Description Chain Out Pin Connection Chain OutChain OUT PIN Connection Primary V.35 Pin Connection Nx56k/64k DTENx 56k/64/ DTE PIN Connection PIN Ccitt DescriptionSelf Test Power UP Testing and InitializationMethods of Operation OperationFront Panel Operation CancelALM LCD WindowT a T U S General Menu OperationO N F I G E T W O R K N N I T Setting the Data FieldCode Z S To Exit Any Menu Field Operation or Display Viewing Display Only Data FieldsFour Opening Menus Menu StructureFour Opening Menu Functions Util Fact RestoreTIME/DATE Software VersionStatus Menu Menu Operation NI Perf RPTS, Submenu of 1Status 1RESET Perf Cntrs15MIN / 24HR Minutes HoursData Values State Active/Inactive Alarm InvestigatedCurr ERR/ALM Submenu of 1Status ERR/ALM Hist Submenu of 1Status Clear HistoryComplete Configuration Menu ConfigurationO R M a T Code Z S Network NI Submenu of 2 ConfigXmit PRM UNIT, Submenu of 2 Config O N T R O L P O R T Alarm SCntrl Port Data Rate AlarmsRate 56/64 PORT, Submenu of Config# of Chan Normal Mode of Operation1Time/Date, Submenu of 3Util UtilKeystroke Summary for Editing Time/Date M E 0 5 0 7 0 T E 0 8 / 0 5 / 93Reinit Unit, Submenu of 3Util 2Software Rev, Submenu of 3UtilE I N I T D D R E S S 0 0 5Fact Restore, Submenu of 3Util4Address,Submenu of 3Util Complete Test Menu Test1Network Tests, Submenu of 4Test Loopback or 3PATTERN 2Run Selftest, Submenu of 4Test R 5 1 1 Error S 5 1 1 Error S = 5T E L O O P B C K O F F S T E M S E L F T E S T3Port Tests submenu of 4Test Operation Far End Looped Back Test Testing ExampleN I T O R 3 U T I L Network Interface TestE T W O R K T E S T S U N S E L F T E S T Press Enter to activate a Remote Payload Loopback Testing Example Appendix a TSU Complete Menu Figure A-1. TSU Complete Menu DiagramAppendix A. TSU Complete Menu DTE Data Rate vs DS0s N # of DS0s N Appendix B DTE Data Rate ChartDTE Rate = 56K Appendix B. DTE Data Rate Chart Numerics IndexIndex Post-Sale Support Presales Inquiries and Applications SupportRepair and Return