ADTRAN 1202890E1 manual Wall Mounting NetVanta 4300/4400 Series, Step Action

Page 48

Unit Installation

NetVanta 4300/4400 Series

 

 

 

 

 

Instructions for Rack Mounting the NetVanta

 

 

Step

Action

1Position the NetVanta in a stationary equipment rack. This unit occupies 1U of space. To allow proper grounding, scrape the paint from the rack around the mounting holes where the NetVanta will be positioned.

2Have an assistant hold the unit in position as you install two mounting bolts through the unit’s brackets and into the equipment rack using a #2 Phillips-head screwdriver.

3Proceed to the steps given in Supplying Power to the Unit on page 49.

Wall Mounting NetVanta 4300/4400 Series

By following these instructions exactly, the NetVanta can be safely mounted to the wall.

•To avoid damaging the unit, use only the screws included in the shipment when attaching mounting ears to the chassis.

•When wall mounting the NetVanta, care must be taken not to damage the power cord. Do not attach the power cord to the building surface or run it through walls, ceilings,

floors, or openings in the building structure.

•The socket-outlet must be installed near the equipment and must be easily accessible.

•When wall mounting the NetVanta 4430, do not remove the SFP slot covers unless an SFP has been installed in the slot.

 

Instructions for Wall Mounting the NetVanta

 

 

Step

Action

 

 

1

Remove the mounting ears from the NetVanta. Rotate them 90o so that the portion of the

 

bracket with the mounting holes is flush with the bottom of the chassis. Reattach them to the

 

chassis (see Figure 20 on page 49).

 

 

2

Decide on a location. All NetVanta 4000 Series units are mounted with the front panel facing

 

up. Keep in mind that the unit needs to be mounted at or below eye level so that the LEDs are

 

visible.

 

Important! Mount the chassis with LEDs facing up (not facing sideways or down).

 

Important! When wall mounting the NetVanta 4430, do not remove the SFP slot covers unless

 

an SFP has been installed in the slot.

 

 

3

Prepare the mounting surface by attaching a board (typically plywood, 3/4-inch to 1-inch thick)

 

to a wall stud using #6 to #10 (2.5-inch or greater in length) wood screws.

 

Important! Mounting to a stud ensures stability. Using sheetrock anchors may not provide

 

sufficient long-term stability.

 

 

4

Have an assistant hold the unit in position as you install two #6 to #10 wood screws through the

 

unit’s brackets and into the mounted board.

 

 

5

Proceed to the steps given in Supplying Power to the Unit on page 49.

 

 

48

Copyright © 2013 ADTRAN, Inc.

61200890E2-34R

Page 47 Page 49
Image 48
Page 47 Page 49
Contents NetVanta 4300/4400 Series Trademarks To the Holder of the ManualSoftware Licensing Agreement Conventions Safety Instructions Save These Important Safety InstructionsFCC-Required Information REN/SOC FIC UsocIsdn BRI DIM Service and Warranty Toll Fraud LiabilityService and Warranty NetVanta 4300/4400 Series Table of Contents Table of Contents NetVanta 4300/4400 Series Appendix A. Connector Pin DefinitionsList of Figures List of Figures NetVanta 4300/4400 Series List of Tables List of Tables NetVanta 4300/4400 Series Introduction NetVanta 4305 Features and Specifications NetVantaNetVanta 4305 Shipping Contents NetVanta 4305 Front Panel Design NetVanta 4305 Rear Panel DesignNET/DBU and Wide Module Option Slots NetVanta 4430 Features and Specifications Power Supply10/100Base-T Ethernet Interface and Activity LEDs SFP Module Slots NetVanta 4430 Shipping Contents NetVanta 4430 Domestic Shipping Contents NetVanta 4305 International Shipping ContentsNetVanta 4430 Rear Panel Design CompactFlashNetVanta 4300/4400 Series Front Panel LEDs NetVanta 4300/4400 Series LEDsColor Indication Option Modules Option Module Shipping Contents NetVanta E1/FE1 + G.703 Drop NIM 1200878E1/L1 NetVanta Serial NIM 1200866E1NetVanta Adsl NIM, Annex a 1202869E1 NetVanta Adsl NIM, Annex B 1202889E1NetVanta Analog Modem DIM 1200864L1 NetVanta Isdn BRI DIM 1200865L1NetVanta Isdn S/T DIM 1200875L1 NetVanta VPN Accelerator Card 1202368L1Network Interface Modules NetVanta 56K/64K NIM P/N 1200861L1Operating Modes Diagnostics NetVanta T1/FT1 NIM P/N 1202862L1T1/FT1 Interface NetVanta T1/FT1 Nebs NIM P/N 1200862L2#NEBS Operating ModesNetVanta T1/FT1 + DSX-1 NIM P/N 1202863L1 Operating Modes Clock SourceDSX-1 Interface NetVanta Dual T1 NIM P/N 1200872L1/1202872L1 T1 InterfaceNetVanta Octal T1/E1 Wide Module P/N 1202843E1 8xT1 Interfaces8xE1 Interfaces T1/E1 Mode DIP Switch NetVanta E1/FE1 NIM P/N 1200868E1/L1 WAN-E1 InterfaceClock Source Physical NetVanta E1/FE1 + G.703 Drop NIM P/N 1200878E1/L1 InterfaceOperating Mode Environmental NetVanta Serial NIM P/N 1200866E1Serial Interface NetVanta Adsl NIM, Annex a P/N 1202869E1 DSL Interface ComplianceNetVanta Adsl NIM, Annex B P/N 1202889E1 Adsl Interface ComplianceOperating Mode NetVanta Shdsl NIM, Annex a P/N 1200936E1Shdsl Interface NetVanta Shdsl NIM, Annex B P/N 1200937E1 NetVanta Shdsl NIM, Annex BNetVanta USB Wwan NIM P/N 1702803F1 USB Interface EnvironmentalDial Backup Interface Modules FeaturesNetVanta Analog Modem DIM P/N 1200864L1 NetVanta Isdn BRI DIM P/N 1200865L1 NetVanta Isdn S/T DIM P/N 1200875L1 Etsi TBRUnit Installation Tools Required Mounting OptionsRack Mounting NetVanta 4300/4400 Series Wall Mounting NetVanta 4300/4400 Series Instructions for Wall Mounting the NetVantaStep Action Supplying Power to the Unit NetVanta 4305 AC and NetVantaInstructions for Connecting DC Power Source to the NetVanta NetVanta 4305 DCInstalling Dial Backup and Network Interface Modules Installing DIMsNIM and DIM Installation Using a USB Cellular Modem with the NetVanta USB Wwan NIM Instructions for Installing the VPN Accelerator Card NetVanta VPN Accelerator Card InstallationInstalling a Sodimm for Expandable Memory Instructions for Installing a SodimmSodimm Installation Keyed Slots Installing a CompactFlash Card Instructions for Installing a CompactFlash CardUnit Installation NetVanta 4300/4400 Series Appendix A. Connector PIN Definitions Table A-1 /100Base-T Ethernet Port Pinouts Name DescriptionTable A-3. SFP Slot Pinouts Name Table A-4. Console Port DCE Pinouts Name DescriptionTable A-5. WAN-DDS Connector Pinouts Name Description Table A-6. WAN-T1 Connector PinoutsTable A-7. WAN-E1 Connector Pinouts Pin Name DescriptionTable A-8. DSX-1 Connector Pinouts Name Description Table A-9. G.703 Connector PinoutsTable A-10. WAN-ADSL NIM Connector Pinouts Table A-11. WAN-SHDSL Connector PinoutsTable A-12. USB Wwan Connector Pinouts Name Description Table A-13. Serial to Cable PinoutsEIA Pin Dial Backup Interface Module Pinouts DBU Connector Table A-15. Isdn S/T DBU Connector Pinouts
Top Page Image Contents