ADTRAN 1202890E1 Installing a Sodimm for Expandable Memory, Instructions for Installing a Sodimm

Page 55

NetVanta 4300/4400 Series

Unit Installation

 

 

Installing a SODIMM for Expandable Memory

The NetVanta 4430 ships with a 200-pin, 256 MB SODIMM (P/N 1200813E1) installed. It can be upgraded to provide 512 MB using the 200-pin, 512 MB SODIMM (P/N 1200814E1). Follow these instructions to install a SODIMM module.

•SODIMMs are intended to be installed only by qualified service personnel.

•There are three types of SODIMM memory modules used by ADTRAN: 200-pin DDR1, 200-pin DDR2, and 144-pin DDR2. Although these modules look very similar, they are

not interchangeable. Prior to beginning the upgrade process, make sure you have purchased the correct upgrade module for your ADTRAN product.

•Before touching electronic components, make sure you are properly grounded. By wearing a wrist strap (or using some other type of static control device), you can prevent static electricity stored on your body or clothing from damaging your installation.

 

Instructions for Installing a SODIMM

 

 

Step

Action

 

 

1

Remove power from the unit.

 

 

2

Remove the screws holding the base unit and the cover together, and, if necessary, the two

 

mounting brackets.

 

 

3

Using a 3/16-inch hex driver, remove the two jack screws located on either side of the DB-9 port.

 

 

4

Carefully lift and remove the unit’s cover to expose the circuit board.

 

 

5

Once you have discharged your static electricity, pick up the SODIMM by its top or sides. Do not

 

touch the gold contacts at the bottom.

 

 

6

Gently insert the module into the memory slot at a slight angle (approximately 30 degrees) as

 

shown in Figure 24 on page 56. Note that the socket and module are both keyed, which means

 

the module can be installed one way only.

 

 

7

To avoid damage, do not use excessive force. To seat the module into the socket, apply firm,

 

even pressure to each end of the module (see the arrows in Figure 25 on page 56) until you feel

 

it slip down into the socket. If you are having problems getting the module to seat properly, try

 

rocking the module up and down slightly, while continuing to apply pressure. When properly

 

seated, the contact fingers on the edge of the module will almost completely disappear inside the

 

socket.

 

 

8

With the module properly seated in the socket, rotate the module downward, as indicated in

 

Figure 26 on page 56. Continue pressing downward until the clips at each end of the socket lock

 

into position. With most sockets, you will hear a distinctive CLICK, indicating the module is

 

correctly locked into position.

 

 

9

Replace the unit cover, screws, and mounting brackets.

 

 

10

Restore power to the unit.

 

 

61200890E2-34R

Copyright © 2013 ADTRAN, Inc.

55

Page 54 Page 56
Image 55
Page 54 Page 56
Contents NetVanta 4300/4400 Series To the Holder of the Manual TrademarksSoftware Licensing Agreement Conventions Save These Important Safety Instructions Safety InstructionsREN/SOC FIC Usoc FCC-Required InformationIsdn BRI DIM Toll Fraud Liability Service and WarrantyService and Warranty NetVanta 4300/4400 Series Table of Contents Appendix A. Connector Pin Definitions Table of Contents NetVanta 4300/4400 SeriesList of Figures List of Figures NetVanta 4300/4400 Series List of Tables List of Tables NetVanta 4300/4400 Series Introduction NetVanta NetVanta 4305 Features and SpecificationsNetVanta 4305 Shipping Contents NetVanta 4305 Rear Panel Design NetVanta 4305 Front Panel DesignNET/DBU and Wide Module Option Slots Power Supply NetVanta 4430 Features and Specifications10/100Base-T Ethernet Interface and Activity LEDs SFP Module Slots NetVanta 4430 Shipping Contents NetVanta 4305 International Shipping Contents NetVanta 4430 Domestic Shipping ContentsCompactFlash NetVanta 4430 Rear Panel DesignNetVanta 4300/4400 Series LEDs NetVanta 4300/4400 Series Front Panel LEDsColor Indication Option Modules Option Module Shipping Contents NetVanta Adsl NIM, Annex B 1202889E1 NetVanta E1/FE1 + G.703 Drop NIM 1200878E1/L1NetVanta Serial NIM 1200866E1 NetVanta Adsl NIM, Annex a 1202869E1NetVanta VPN Accelerator Card 1202368L1 NetVanta Analog Modem DIM 1200864L1NetVanta Isdn BRI DIM 1200865L1 NetVanta Isdn S/T DIM 1200875L1NetVanta 56K/64K NIM P/N 1200861L1 Network Interface ModulesNetVanta T1/FT1 NIM P/N 1202862L1 Operating Modes DiagnosticsT1/FT1 Interface Operating Modes NetVanta T1/FT1 Nebs NIM P/N 1200862L2#NEBSOperating Modes Clock Source NetVanta T1/FT1 + DSX-1 NIM P/N 1202863L1DSX-1 Interface T1 Interface NetVanta Dual T1 NIM P/N 1200872L1/1202872L18xT1 Interfaces NetVanta Octal T1/E1 Wide Module P/N 1202843E18xE1 Interfaces T1/E1 Mode DIP Switch WAN-E1 Interface NetVanta E1/FE1 NIM P/N 1200868E1/L1Clock Source Physical Interface NetVanta E1/FE1 + G.703 Drop NIM P/N 1200878E1/L1NetVanta Serial NIM P/N 1200866E1 Operating Mode EnvironmentalSerial Interface DSL Interface Compliance NetVanta Adsl NIM, Annex a P/N 1202869E1Adsl Interface Compliance NetVanta Adsl NIM, Annex B P/N 1202889E1NetVanta Shdsl NIM, Annex a P/N 1200936E1 Operating ModeShdsl Interface NetVanta Shdsl NIM, Annex B NetVanta Shdsl NIM, Annex B P/N 1200937E1USB Interface Environmental NetVanta USB Wwan NIM P/N 1702803F1Features Dial Backup Interface ModulesNetVanta Analog Modem DIM P/N 1200864L1 NetVanta Isdn BRI DIM P/N 1200865L1 Etsi TBR NetVanta Isdn S/T DIM P/N 1200875L1Unit Installation Mounting Options Tools RequiredRack Mounting NetVanta 4300/4400 Series Instructions for Wall Mounting the NetVanta Wall Mounting NetVanta 4300/4400 SeriesStep Action NetVanta 4305 AC and NetVanta Supplying Power to the UnitNetVanta 4305 DC Instructions for Connecting DC Power Source to the NetVantaInstalling DIMs Installing Dial Backup and Network Interface ModulesNIM and DIM Installation Using a USB Cellular Modem with the NetVanta USB Wwan NIM NetVanta VPN Accelerator Card Installation Instructions for Installing the VPN Accelerator CardInstructions for Installing a Sodimm Installing a Sodimm for Expandable MemorySodimm Installation Keyed Slots Instructions for Installing a CompactFlash Card Installing a CompactFlash CardUnit Installation NetVanta 4300/4400 Series Table A-1 /100Base-T Ethernet Port Pinouts Name Description Appendix A. Connector PIN DefinitionsTable A-4. Console Port DCE Pinouts Name Description Table A-3. SFP Slot Pinouts NamePin Name Description Table A-5. WAN-DDS Connector Pinouts Name DescriptionTable A-6. WAN-T1 Connector Pinouts Table A-7. WAN-E1 Connector PinoutsTable A-11. WAN-SHDSL Connector Pinouts Table A-8. DSX-1 Connector Pinouts Name DescriptionTable A-9. G.703 Connector Pinouts Table A-10. WAN-ADSL NIM Connector PinoutsTable A-13. Serial to Cable Pinouts Table A-12. USB Wwan Connector Pinouts Name DescriptionEIA Pin Table A-15. Isdn S/T DBU Connector Pinouts Dial Backup Interface Module Pinouts DBU Connector
Top Page Image Contents