3Com WL-575, 3CRWEASYA73 manual Ip address ip-address netmask gateway no ip address

Page 219

Using the Command Line Interface

Related Commands

show interface ethernet (6-110)

ip address

This command sets the IP address for the access point. Use the no form to restore the default IP address.

Syntax

ip address <ip-address> <netmask> <gateway> no ip address

•ip-address- IP address

•netmask - Network mask for the associated IP subnet. This mask identifies the host address bits used for routing to specific subnets.

•gateway - IP address of the default gateway

Default Setting

IP address: 192.254.2.1

Netmask: 255.255.255.0

Command Mode

Interface Configuration (Ethernet)

Command Usage

•DHCP is enabled by default. To manually configure a new IP address, you must first disable the DHCP client with the no ip dhcp command.

•You must assign an IP address to this device to gain management access over the network or to connect the access point to existing IP subnets. You can manually configure a specific IP address using this command, or direct the device to obtain an address from a DHCP server using the ip dhcp command. Valid IP addresses consist of four numbers, 0 to 255, separated by periods. Anything outside this format will not be accepted by the configuration program.

Example

Outdoor 11a Building to Building (config)#interface ethernet Enter Ethernet configuration commands, one per line.

Outdoor 11a Building to Building (if-ethernet)#ip address 192.254.2.1 255.255.255.0 192.254.2.253

Outdoor 11a Building to Building (if-ethernet)#

Related Commands

ip dhcp (6-108)

6-107

Image 219

Contents User Guide 3Com Corporation 350 Campus Drive Marlborough, MA Contents Configuring Sntp Advanced Setup System IdentificationAuthentication Filter Control Configuring Snmp and Trap Message ParametersCommand Line Interface Pin DIN to RJ-45 Cable Wiring B-6 Straight-Through Wiring Crossover Wiring B-4Terminology Viii Introduction Product FeaturesApproved Channels Radio Characteristics„ One Quick Start Guide Package ChecklistHardware Description Integrated HIGH-GAIN AntennaExternal Antenna Options Ethernet Port Power Injector ModuleWater Tight Test Point Grounding PointSystem Configuration Operating ModesWALL- and POLE-MOUNTING Bracket KIT POINT-TO-MULTIPOINT Configuration POINT-TO-POINT ConfigurationBeam Angle Page Bridge Link Planning Data Rates Radio Path Planning Antenna Height Miles 4.8 km 20 m 17 m 12 m Antenna Position and Orientation Weather Conditions Radio InterferenceGrounding Ethernet CablingHardware Installation Testing Basic Link Operation Using the POLE-MOUNTING BracketMount the Unit Fit the edges of the V-shaped Part into the slots Using the WALL-MOUNTING Bracket Page Connect External Antennas Connect Cables to the Unit Connect the Power InjectorPage LED Check the LED IndicatorsAlign Antennas High 11a Signal Page Networks Without a Dhcp Server Networks with a Dhcp ServerLaunching the 3COM Wireless Interface Device Manager Using the 3COM Installation CDClick on the Properties button to see the following screen First Time only Using the Setup WizardLogin Home page displays the Main Menu Setup Wizard Step Setup Wizard Step Setup Wizard Step Click Finish Click the OK button to complete the wizard System Configuration Advanced Setup Advanced SetupAdvanced Setup System Identification TCP / IP Settings System Configuration Smart Monitor Radius Radius Authentication Authentication Authentication Authentication Authentication System Configuration Filter Control System Configuration Vlan Filter Control Vlan ID Snmp Configuring Snmp and Trap Message ParametersSnmp Trap Configuration Configuring SNMPv3 Users Configuring SNMPV3 UsersChanging the Password AdministrationTelnet and SSH Settings Upgrading Firmware System Configuration „ IP Address IP address or host name of the Tftp server WDS and Spanning Tree Settings WDS and Spanning Tree Settings Root bridge acting as the master bridges parent WDS and Spanning Tree Settings Range Default Enabling System Logging System LOGError Level Description Configuring SntpRssi Rssi Radio Interface 802.11A Interface Radio Settings aRadio Settings a and B/G Configuring Common Radio SettingsSystem Configuration Normal Mode Turbo Mode System Configuration 802.11B/G Interface Radio Settings B/G Configuring WI-FI Multimedia Voice WMM Access CategoriesAccess CategoryWMM Backoff Times System Configuration Key Type See Wired Equivalent Privacy WEP Wi-Fi Protected Access WPA or WPA2 Wireless Security ConsiderationsSecurity MAC Radius Combination Authentication b Server Radius Wired Equivalent Privacy WEPAuthentication and Encryption WPA Key Management WEP Keys Wi-Fi Protected Access WPA System Configuration WPA Configuration Settings Configuration settings for WPA are summarized belowAP Status Status InformationStation Status Static The client is using static WEP keys for encryption Security System Configuration Using the Command Line Interface Accessing the CLIConsole Connection Telnet Connection Keywords and Arguments Entering CommandsShowing Commands Command Modes Negating the Effect of CommandsConfiguration Commands Keystroke Commands Command GroupsGeneral Commands ConfigureGeneral Commands Example Default SettingCommand Mode Related CommandsSyntax Command UsageExit PingSyntax Reset board configuration ResetShow line Show historySystem Management Commands System Management CommandsCountry Country Codes Country countrycodeSyntax Prompt string no prompt PromptSyntax Username name System nameSyntax System name name no system name UsernameIp ssh-server enable PasswordSyntax Ip ssh-server port port-number Default Setting Command ModeIp telnet-server enable Ip ssh-server portIp http server Syntax No ip http server Default SettingIp http port Syntax Ip http port port-numberno ip http portSyntax Ip https port portnumber no ip https port Ip https portIp https server Syntax No ip https server Default SettingWeb-redirect Syntax No web-redirect Default SettingAPmgmtIP multiple IPaddress subnetmask single IPaddress any APmgmtIPAPmgmtUI Syntax APmgmtUI Snmp Telnet Web enable disableSnmp UI Show apmanagementUS United States Show systemShow version Show configSsid PRE Shared KEY WPA PSK Enabled Dot11StationRequestFail Nocountryset System Logging Commands System Loggign CommandsShow hardware Syntax No logging on Default Setting Logging onLogging host Syntax No logging console Default Setting Logging consoleLogging level Syntax Logging facility-type type Logging facility-typeShow logging Syntax Logging clear Command ModeSyntax Show logging Command Mode Logging clearShow event-log System Clock CommandsSyntax Show event-log Command Mode System Clock CommandsSyntax Sntp-server ip 1 2 ip Sntp-server enableSyntax No sntp-server enable Sntp-server ipSntp-server ip 6-38 show sntp Sntp-server date-timeSyntax Sntp-server timezone hours Syntax No sntp-server daylight-saving Default SettingSntp-server daylight-saving Sntp-server timezoneTAIPEI, Beijing Show sntpDhcp Relay Commands Dhcp Relay CommandsDhcp-relay enable Syntax No dhcp-relay enable Default SettingDhcp-relay Syntax Dhcp-relay primary secondary ipaddressShow dhcp-relay Snmp Commands Snmp CommandsDisplays the Snmp v3 notification filter assignments Snmp-server contact Snmp-server communitySnmp-server location Snmp-server host Snmp-server enable serverSnmp-server trap Hostname Name of the host. Range 1-63 charactersCommand Line Interface Snmp-server engine-id Syntax Snmp-server user user-name Snmp-server userSnmp-server targets Snmp-server filter Default Setting Show snmp groups Snmp-server filter-assignmentsShow snmp group-assignments Syntax Show snmp groups Command ModeSyntax Show snmp users Command Mode Show snmp usersShow snmp filter Syntax Show snmp group-assignments Command ModeSyntax Show snmp target Command Mode Show snmp targetShow snmp filter-assignments Syntax Show snmp filter-assignments Command ModeShow snmp Flash/File Commands Flash/File CommandsBootfile Syntax Bootfile filenameCopy Syntax Copy ftp tftp file copy config ftp tftpDelete File information is shown below DirRadius Client Show bootfileRadius-server address Radius-server portSyntax Radius-server secondary port portnumber Syntax Radius-server secondary retransmit numberofretries Radius-server keySyntax Radius-server secondary key keystring Radius-server retransmitSyntax Radius-server secondary port-accounting portnumber Radius-server timeoutSyntax Radius-server secondary timeout numberofseconds Radius-server port-accountingRadius-server radius-mac-format Radius-server timeout-interimRadius-server vlan-format Syntax Radius-server vlan-format hex asciiShow radius 802.1X Authentication 802.1X Authentication 802.1xSyntax 802.1x supported required no Using the Command Line Interface Syntax 802.1x broadcast-key-refresh-rate rate 802.1x broadcast-key-refresh-rate802.1x session-timeout 802.1x session-key-refresh-rateSyntax 802.1x session-key-refresh-rate rate Default 802.1x-supplicant enable802.1x-supplicant user Show authentication MAC Address Authentication Syntax Address filter entry mac-addressallowed denied Address filter defaultSyntax Address filter default allowed denied Address filter entryAddress filter default 6-79 802.1x-supplicant user Syntax Address filter delete mac-address Mac-authentication serverSyntax Mac-authentication server local remote Address filter deleteFiltering Commands Mac-authentication session-timeoutSyntax Mac-authentication session-timeout minutes Filter local-bridge Filtering CommandsOutdoor 11a Building to Building config#filter local-bridge Filter ap-manage Syntax No filter ap-manage DefaultFilter uplink enable Syntax No filter uplink enable DefaultSyntax No filter ethernet-type enable Default Filter ethernet-type enableShow filters Filter ethernet-type protocolWDS Bridge Commands WDS Bridge CommandsSyntax Bridge role ap repeater bridge root-bridge Bridge modeSyntax Bridge mode master slave Bridge role WDSBridge channel-auto-sync Syntax Bridge channel-auto-sync enable disableSyntax Bridge-link child index mac-address Bridge-link parentSyntax Bridge-link parent mac-address Bridge-link childSyntax Bridge dynamic-entry age-time seconds Bridge dynamic-entry age-timeSeconds Show bridge aging-time Show bridge filter-entry MAC Show bridge link Syntax Show bridge link ethernet wireless a g indexParent 00-12-34-56-78-9a Child Spanning Tree Commands Bridge stp enableBridge Commands Bridge stp forwarding-delay Syntax No bridge stp enable Default SettingBridge stp hello-time Syntax Bridge stp hello-time time No bridge stp hello-timeBridge stp max-age Syntax Bridge stp max-age seconds No bridge stp max-age Bridge stp prioritySyntax Bridge stp prioritypriority no bridge stp priority Syntax Bridge-link path-cost index cost Bridge-link path-costBridge-link port-priority Syntax Bridge-link port-priority index priorityShow bridge stp Ethernet Interface Commands Syntax Show bridge stp Command ModeEhternet Interface Commands Dns server Interface ethernetIp address ip-address netmask gateway no ip address Ip addressIp dhcp Syntax No ip dhcp Default SettingShutdown Syntax No shutdown Default SettingSpeed-duplex Syntax Speed-duplex auto 10MH 10MF 100MF 100MHShow interface ethernet Syntax Show interface ethernet Default SettingWireless Interface Commands Wireless Interface CommandsSyntax Interface wireless a g Interface wirelessVap SpeedSyntax Speed speed Syntax Turbo static dynamic no turbo TurboSyntax Multicast-data-rate speed Multicast-data-rateSyntax Channel channel auto ChannelTransmit-power Radio-modeSyntax Radio-mode b g b+g Default Setting +g mode Command Mode PreambleSyntax Preamble long short-or-long Syntax Antenna control diversity left right Antenna controlSyntax Antenna location indoor outdoor Antenna idSyntax Antenna id antenna-id Antenna locationSyntax Beacon-interval interval Beacon-intervalSyntax Dtim-period interval Dtim-periodSyntax Rts-threshold threshold Fragmentation-lengthSyntax Fragmentation-length length Rts-thresholdSuper-a Syntax No super-a Default SettingSyntax No super-g Default Setting Super-gDescription Syntax No closed-system Default Setting SsidClosed-system Syntax Max-association count Assoc-timeout-intervalSyntax Assoc-timeout-interval minutes Max-associationSyntax Auth-timeout-value minutes Auth-timeout-valueSyntax Show interface wireless a g vap-id Show interface wireless130 131 132 Show station Rogue AP Detection CommandsRogue AP Commands Rogue-ap enableSyntax No rogue-ap authenticate Default Setting Rogue-ap authenticateRogue-ap duration Syntax Rogue-ap duration millisecondsRogue-ap interval Rogue-ap scan Syntax Rogue-ap interval minutes138 Wireless Security Commands Wireless Security CommandsShow rogue-ap Auth 141 Encryption Syntax No encryption Default SettingKey index size type value no key index KeyTransmit-key Syntax Transmit-key indexKey 6-143 encryption 6-142 transmit-key Syntax Cipher-suite aes-ccmp tkip wep Cipher-suiteSyntax Micmode hardware software MicmodeSyntax Wpa-pre-shared-key hex passphrase-keyvalue Wpa-pre-shared-keySyntax Pmksa-lifetime minutes Pmksa-lifetimePre-authentication Link-integrity ping-detect Link Integrity CommandsSyntax No link-integrity ping-detect Default Setting Link Integrity CommandsLink-integrity ping-host Link-integrity ping-intervalSyntax Link-integrity ping-interval interval Link-integrity ping-fail-retry Syntax Link-integrity ping-fail-retry countsLink-integrity ethernet-detect Iapp Commands Syntax No link-integrity ethernet-detect Default SettingShow link-integrity Vlan Commands Syntax No iapp DefaultIapp Vlan Commands Management-vlanid Syntax No vlan enable DefaultCommand Description VlanSyntax Vlan-id vlan-id Vlan-idSyntax No wmm supported required WMM CommandsWMM Commands WmmSyntax Wmm-acknowledge-policy acnumber ack noack Wmm-acknowledge-policyWmmparam AP Access Point BSS Wireless client161 162 Troubleshooting Page Page Page TWISTED-PAIR Cable Assignments Cables and Pinouts10/100BASE-TX PIN Assignments STRAIGHT-THROUGH Wiring Crossover Wiring Pin DIN Ethernet Port Pinout PIN DIN Connector PinoutPIN DIN to RJ-45 Cable Wiring Glossary CSMA/CA Infrastructure Radius Virtual LAN Vlan Glossary-6 Index RTS STA

Related manuals

Manual 20 pages 14.36 Kb