3Com 3CRWEASYA73, WL-575 manual

Page 38

1Pan the antenna horizontally back and forth while checking the LEDs. If using the pole-mounting bracket with the unit, you must rotate the mounting bracket around the pole. Other external antenna brackets may require a different horizontal adjustment.

2Find the point where the signal is strongest (all LEDs on) and secure the horizontal adjustment in that position.

NOTE: Sometimes there may not be a central lobe peak in the voltage because vertical alignment is too far off; only two similar peaks for the side lobes are detected. In this case, fix the antenna so that it is halfway between the two peaks.

3Loosen the vertical adjustment on the mounting bracket and tilt the antenna slowly up and down while checking the LEDs.

4Find the point where the signal is strongest and secure the vertical adjustment in that position.

3-12

Image 38

Contents User Guide 3Com Corporation 350 Campus Drive Marlborough, MA Contents Configuring Snmp and Trap Message Parameters Advanced Setup System IdentificationAuthentication Filter Control Configuring SntpCommand Line Interface Straight-Through Wiring Crossover Wiring B-4 Pin DIN to RJ-45 Cable Wiring B-6Terminology Viii Product Features IntroductionRadio Characteristics Approved ChannelsPackage Checklist „ One Quick Start GuideExternal Antenna Options Hardware DescriptionIntegrated HIGH-GAIN Antenna Power Injector Module Ethernet PortGrounding Point Water Tight Test PointWALL- and POLE-MOUNTING Bracket KIT System ConfigurationOperating Modes POINT-TO-POINT Configuration POINT-TO-MULTIPOINT ConfigurationBeam Angle Page Bridge Link Planning Data Rates Radio Path Planning Antenna Height Miles 4.8 km 20 m 17 m 12 m Antenna Position and Orientation Radio Interference Weather ConditionsEthernet Cabling GroundingHardware Installation Mount the Unit Testing Basic Link OperationUsing the POLE-MOUNTING Bracket Fit the edges of the V-shaped Part into the slots Using the WALL-MOUNTING Bracket Page Connect External Antennas Connect the Power Injector Connect Cables to the UnitPage Check the LED Indicators LEDAlign Antennas High 11a Signal Page Networks with a Dhcp Server Networks Without a Dhcp ServerUsing the 3COM Installation CD Launching the 3COM Wireless Interface Device ManagerClick on the Properties button to see the following screen Using the Setup Wizard First Time onlyLogin Home page displays the Main Menu Setup Wizard Step Setup Wizard Step Setup Wizard Step Click Finish Click the OK button to complete the wizard System Configuration Advanced Setup Advanced SetupAdvanced Setup System Identification TCP / IP Settings System Configuration Smart Monitor Radius Radius Authentication Authentication Authentication Authentication Authentication System Configuration Filter Control System Configuration Vlan Filter Control Vlan ID Configuring Snmp and Trap Message Parameters SnmpSnmp Trap Configuration Configuring SNMPV3 Users Configuring SNMPv3 UsersAdministration Changing the PasswordTelnet and SSH Settings Upgrading Firmware System Configuration „ IP Address IP address or host name of the Tftp server WDS and Spanning Tree Settings WDS and Spanning Tree Settings Root bridge acting as the master bridges parent WDS and Spanning Tree Settings Range Default System LOG Enabling System LoggingConfiguring Sntp Error Level DescriptionRssi Rssi Radio Interface Radio Settings a 802.11A InterfaceConfiguring Common Radio Settings Radio Settings a and B/GSystem Configuration Normal Mode Turbo Mode System Configuration 802.11B/G Interface Radio Settings B/G Configuring WI-FI Multimedia Category WMM Access CategoriesAccess VoiceWMM Backoff Times System Configuration Key Type See Wired Equivalent Privacy WEP Security Wi-Fi Protected Access WPA or WPA2Wireless Security Considerations MAC Radius Combination Authentication b Server Wired Equivalent Privacy WEP RadiusAuthentication and Encryption WPA Key Management WEP Keys Wi-Fi Protected Access WPA System Configuration Configuration settings for WPA are summarized below WPA Configuration SettingsStatus Information AP StatusStation Status Static The client is using static WEP keys for encryption Security System Configuration Console Connection Using the Command Line InterfaceAccessing the CLI Telnet Connection Entering Commands Keywords and ArgumentsShowing Commands Negating the Effect of Commands Command ModesConfiguration Commands Command Groups Keystroke CommandsGeneral Commands General CommandsConfigure Related Commands Default SettingCommand Mode ExamplePing Command UsageExit SyntaxReset Syntax Reset board configurationShow history Show lineCountry System Management CommandsSystem Management Commands Country countrycode Country CodesPrompt Syntax Prompt string no promptUsername System nameSyntax System name name no system name Syntax Username namePassword Ip ssh-server enableIp ssh-server port Default Setting Command ModeIp telnet-server enable Syntax Ip ssh-server port port-numberSyntax Ip http port port-numberno ip http port Syntax No ip http server Default SettingIp http port Ip http serverIp https port Syntax Ip https port portnumber no ip https portSyntax No ip https server Default Setting Ip https serverSyntax No web-redirect Default Setting Web-redirectAPmgmtIP APmgmtIP multiple IPaddress subnetmask single IPaddress anySyntax APmgmtUI Snmp Telnet Web enable disable APmgmtUIShow apmanagement Snmp UIShow system US United StatesShow config Show versionSsid PRE Shared KEY WPA PSK Enabled Dot11StationRequestFail Nocountryset Show hardware System Logging CommandsSystem Loggign Commands Logging host Syntax No logging on Default SettingLogging on Logging level Syntax No logging console Default SettingLogging console Logging facility-type Syntax Logging facility-type typeLogging clear Syntax Logging clear Command ModeSyntax Show logging Command Mode Show loggingSystem Clock Commands System Clock CommandsSyntax Show event-log Command Mode Show event-logSntp-server ip Sntp-server enableSyntax No sntp-server enable Syntax Sntp-server ip 1 2 ipSntp-server date-time Sntp-server ip 6-38 show sntpSntp-server timezone Syntax No sntp-server daylight-saving Default SettingSntp-server daylight-saving Syntax Sntp-server timezone hoursShow sntp TAIPEI, BeijingSyntax No dhcp-relay enable Default Setting Dhcp Relay CommandsDhcp-relay enable Dhcp Relay CommandsShow dhcp-relay Dhcp-relaySyntax Dhcp-relay primary secondary ipaddress Snmp Commands Snmp CommandsDisplays the Snmp v3 notification filter assignments Snmp-server community Snmp-server contactSnmp-server location Snmp-server enable server Snmp-server hostHostname Name of the host. Range 1-63 characters Snmp-server trapCommand Line Interface Snmp-server engine-id Snmp-server user Syntax Snmp-server user user-nameSnmp-server targets Snmp-server filter Default Setting Snmp-server filter-assignments Show snmp groupsShow snmp users Syntax Show snmp groups Command ModeSyntax Show snmp users Command Mode Show snmp group-assignmentsShow snmp target Syntax Show snmp group-assignments Command ModeSyntax Show snmp target Command Mode Show snmp filterSyntax Show snmp filter-assignments Command Mode Show snmp filter-assignmentsShow snmp Syntax Bootfile filename Flash/File CommandsBootfile Flash/File CommandsSyntax Copy ftp tftp file copy config ftp tftp CopyDelete Dir File information is shown belowShow bootfile Radius ClientSyntax Radius-server secondary port portnumber Radius-server addressRadius-server port Radius-server retransmit Radius-server keySyntax Radius-server secondary key keystring Syntax Radius-server secondary retransmit numberofretriesRadius-server port-accounting Radius-server timeoutSyntax Radius-server secondary timeout numberofseconds Syntax Radius-server secondary port-accounting portnumberRadius-server timeout-interim Radius-server radius-mac-formatShow radius Radius-server vlan-formatSyntax Radius-server vlan-format hex ascii 802.1X Authentication Syntax 802.1x supported required no 802.1X Authentication802.1x Using the Command Line Interface 802.1x broadcast-key-refresh-rate Syntax 802.1x broadcast-key-refresh-rate rateSyntax 802.1x session-key-refresh-rate rate 802.1x session-timeout802.1x session-key-refresh-rate 802.1x-supplicant user Default802.1x-supplicant enable Show authentication MAC Address Authentication Address filter entry Address filter defaultSyntax Address filter default allowed denied Syntax Address filter entry mac-addressallowed deniedAddress filter default 6-79 802.1x-supplicant user Address filter delete Mac-authentication serverSyntax Mac-authentication server local remote Syntax Address filter delete mac-addressSyntax Mac-authentication session-timeout minutes Filtering CommandsMac-authentication session-timeout Filtering Commands Filter local-bridgeOutdoor 11a Building to Building config#filter local-bridge Syntax No filter uplink enable Default Syntax No filter ap-manage DefaultFilter uplink enable Filter ap-manageFilter ethernet-type enable Syntax No filter ethernet-type enable DefaultFilter ethernet-type protocol Show filtersWDS Bridge Commands WDS Bridge CommandsBridge role WDS Bridge modeSyntax Bridge mode master slave Syntax Bridge role ap repeater bridge root-bridgeSyntax Bridge channel-auto-sync enable disable Bridge channel-auto-syncBridge-link child Bridge-link parentSyntax Bridge-link parent mac-address Syntax Bridge-link child index mac-addressBridge dynamic-entry age-time Syntax Bridge dynamic-entry age-time secondsSeconds Show bridge aging-time Show bridge filter-entry MAC Syntax Show bridge link ethernet wireless a g index Show bridge linkParent 00-12-34-56-78-9a Child Bridge Commands Spanning Tree CommandsBridge stp enable Syntax No bridge stp enable Default Setting Bridge stp forwarding-delayBridge stp max-age Bridge stp hello-timeSyntax Bridge stp hello-time time No bridge stp hello-time Syntax Bridge stp prioritypriority no bridge stp priority Syntax Bridge stp max-age seconds No bridge stp max-ageBridge stp priority Bridge-link path-cost Syntax Bridge-link path-cost index costShow bridge stp Bridge-link port-prioritySyntax Bridge-link port-priority index priority Ehternet Interface Commands Ethernet Interface CommandsSyntax Show bridge stp Command Mode Interface ethernet Dns serverIp address Ip address ip-address netmask gateway no ip addressSyntax No ip dhcp Default Setting Ip dhcpSyntax Speed-duplex auto 10MH 10MF 100MF 100MH Syntax No shutdown Default SettingSpeed-duplex ShutdownSyntax Show interface ethernet Default Setting Show interface ethernetWireless Interface Commands Wireless Interface CommandsInterface wireless Syntax Interface wireless a gSyntax Speed speed VapSpeed Turbo Syntax Turbo static dynamic no turboMulticast-data-rate Syntax Multicast-data-rate speedChannel Syntax Channel channel autoSyntax Radio-mode b g b+g Transmit-powerRadio-mode Syntax Preamble long short-or-long Default Setting +g mode Command ModePreamble Antenna control Syntax Antenna control diversity left rightAntenna location Antenna idSyntax Antenna id antenna-id Syntax Antenna location indoor outdoorBeacon-interval Syntax Beacon-interval intervalDtim-period Syntax Dtim-period intervalRts-threshold Fragmentation-lengthSyntax Fragmentation-length length Syntax Rts-threshold thresholdSyntax No super-a Default Setting Super-aDescription Syntax No super-g Default SettingSuper-g Closed-system Syntax No closed-system Default SettingSsid Max-association Assoc-timeout-intervalSyntax Assoc-timeout-interval minutes Syntax Max-association countAuth-timeout-value Syntax Auth-timeout-value minutesShow interface wireless Syntax Show interface wireless a g vap-id130 131 132 Rogue AP Detection Commands Show stationRogue-ap enable Rogue AP CommandsRogue-ap authenticate Syntax No rogue-ap authenticate Default SettingRogue-ap interval Rogue-ap durationSyntax Rogue-ap duration milliseconds Syntax Rogue-ap interval minutes Rogue-ap scan138 Show rogue-ap Wireless Security CommandsWireless Security Commands Auth 141 Syntax No encryption Default Setting EncryptionKey Key index size type value no key indexKey 6-143 encryption 6-142 transmit-key Transmit-keySyntax Transmit-key index Cipher-suite Syntax Cipher-suite aes-ccmp tkip wepMicmode Syntax Micmode hardware softwareWpa-pre-shared-key Syntax Wpa-pre-shared-key hex passphrase-keyvaluePmksa-lifetime Syntax Pmksa-lifetime minutesPre-authentication Link Integrity Commands Link Integrity CommandsSyntax No link-integrity ping-detect Default Setting Link-integrity ping-detectSyntax Link-integrity ping-interval interval Link-integrity ping-hostLink-integrity ping-interval Link-integrity ethernet-detect Link-integrity ping-fail-retrySyntax Link-integrity ping-fail-retry counts Show link-integrity Iapp CommandsSyntax No link-integrity ethernet-detect Default Setting Iapp Vlan CommandsSyntax No iapp Default Vlan Commands Vlan Syntax No vlan enable DefaultCommand Description Management-vlanidVlan-id Syntax Vlan-id vlan-idWmm WMM CommandsWMM Commands Syntax No wmm supported requiredWmm-acknowledge-policy Syntax Wmm-acknowledge-policy acnumber ack noackAP Access Point BSS Wireless client Wmmparam161 162 Troubleshooting Page Page Page Cables and Pinouts TWISTED-PAIR Cable Assignments10/100BASE-TX PIN Assignments STRAIGHT-THROUGH Wiring Crossover Wiring PIN DIN Connector Pinout Pin DIN Ethernet Port PinoutPIN DIN to RJ-45 Cable Wiring Glossary CSMA/CA Infrastructure Radius Virtual LAN Vlan Glossary-6 Index RTS STA

Related manuals

Manual 20 pages 14.36 Kb