3Com 3CRWEASYA73 Testing Basic Link Operation, Mount the Unit, Using the POLE-MOUNTING Bracket

Page 28

TESTING BASIC LINK OPERATION

Set up the units over a very short range (15 to 25 feet), either outdoors or indoors. Connect the units as indicated in this chapter and be sure to perform all the basic configuration tasks outlined in Chapter 4, “Initial Configuration.” When you are satisfied that the links are operating correctly, proceed to mount the units in their intended locations.

MOUNT THE UNIT

The bridge can be mounted on the following types of surfaces:

Pole

Wall

CAUTION: The bridge is intended for outdoor use only. Do not install the bridge ! indoors.

USING THE POLE-MOUNTING BRACKET

Perform the following steps to mount the unit to a 1.5 to 2 inch diameter steel pole or tube using the mounting bracket:

1 Place the V-shaped part of the bracket around the pole and tighten the securing nuts just enough to hold the bracket to the pole. (The bracket may need to be rotated around the pole during the antenna alignment process.)

Attach V-shaped parts to pole with provided nuts and bolts

3-2

Image 28

Contents User Guide 3Com Corporation 350 Campus Drive Marlborough, MA Contents Advanced Setup System Identification Authentication Filter ControlConfiguring Snmp and Trap Message Parameters Configuring SntpCommand Line Interface Straight-Through Wiring Crossover Wiring B-4 Pin DIN to RJ-45 Cable Wiring B-6Terminology Viii Product Features IntroductionRadio Characteristics Approved ChannelsPackage Checklist „ One Quick Start GuideIntegrated HIGH-GAIN Antenna Hardware DescriptionExternal Antenna Options Power Injector Module Ethernet PortGrounding Point Water Tight Test PointOperating Modes System ConfigurationWALL- and POLE-MOUNTING Bracket KIT POINT-TO-POINT Configuration POINT-TO-MULTIPOINT ConfigurationBeam Angle Page Bridge Link Planning Data Rates Radio Path Planning Antenna Height Miles 4.8 km 20 m 17 m 12 m Antenna Position and Orientation Radio Interference Weather ConditionsEthernet Cabling GroundingHardware Installation Using the POLE-MOUNTING Bracket Testing Basic Link OperationMount the Unit Fit the edges of the V-shaped Part into the slots Using the WALL-MOUNTING Bracket Page Connect External Antennas Connect the Power Injector Connect Cables to the UnitPage Check the LED Indicators LEDAlign Antennas High 11a Signal Page Networks with a Dhcp Server Networks Without a Dhcp ServerUsing the 3COM Installation CD Launching the 3COM Wireless Interface Device ManagerClick on the Properties button to see the following screen Using the Setup Wizard First Time onlyLogin Home page displays the Main Menu Setup Wizard Step Setup Wizard Step Setup Wizard Step Click Finish Click the OK button to complete the wizard System Configuration Advanced Setup Advanced SetupAdvanced Setup System Identification TCP / IP Settings System Configuration Smart Monitor Radius Radius Authentication Authentication Authentication Authentication Authentication System Configuration Filter Control System Configuration Vlan Filter Control Vlan ID Configuring Snmp and Trap Message Parameters SnmpSnmp Trap Configuration Configuring SNMPV3 Users Configuring SNMPv3 UsersAdministration Changing the PasswordTelnet and SSH Settings Upgrading Firmware System Configuration „ IP Address IP address or host name of the Tftp server WDS and Spanning Tree Settings WDS and Spanning Tree Settings Root bridge acting as the master bridges parent WDS and Spanning Tree Settings Range Default System LOG Enabling System LoggingConfiguring Sntp Error Level DescriptionRssi Rssi Radio Interface Radio Settings a 802.11A InterfaceConfiguring Common Radio Settings Radio Settings a and B/GSystem Configuration Normal Mode Turbo Mode System Configuration 802.11B/G Interface Radio Settings B/G Configuring WI-FI Multimedia WMM Access Categories AccessCategory VoiceWMM Backoff Times System Configuration Key Type See Wired Equivalent Privacy WEP Wireless Security Considerations Wi-Fi Protected Access WPA or WPA2Security MAC Radius Combination Authentication b Server Wired Equivalent Privacy WEP RadiusAuthentication and Encryption WPA Key Management WEP Keys Wi-Fi Protected Access WPA System Configuration Configuration settings for WPA are summarized below WPA Configuration SettingsStatus Information AP StatusStation Status Static The client is using static WEP keys for encryption Security System Configuration Accessing the CLI Using the Command Line InterfaceConsole Connection Telnet Connection Entering Commands Keywords and ArgumentsShowing Commands Negating the Effect of Commands Command ModesConfiguration Commands Command Groups Keystroke CommandsConfigure General CommandsGeneral Commands Default Setting Command ModeRelated Commands ExampleCommand Usage ExitPing SyntaxReset Syntax Reset board configurationShow history Show lineSystem Management Commands System Management CommandsCountry Country countrycode Country CodesPrompt Syntax Prompt string no promptSystem name Syntax System name name no system nameUsername Syntax Username namePassword Ip ssh-server enableDefault Setting Command Mode Ip telnet-server enableIp ssh-server port Syntax Ip ssh-server port port-numberSyntax No ip http server Default Setting Ip http portSyntax Ip http port port-numberno ip http port Ip http serverIp https port Syntax Ip https port portnumber no ip https portSyntax No ip https server Default Setting Ip https serverSyntax No web-redirect Default Setting Web-redirectAPmgmtIP APmgmtIP multiple IPaddress subnetmask single IPaddress anySyntax APmgmtUI Snmp Telnet Web enable disable APmgmtUIShow apmanagement Snmp UIShow system US United StatesShow config Show versionSsid PRE Shared KEY WPA PSK Enabled Dot11StationRequestFail Nocountryset System Loggign Commands System Logging CommandsShow hardware Logging on Syntax No logging on Default SettingLogging host Logging console Syntax No logging console Default SettingLogging level Logging facility-type Syntax Logging facility-type typeSyntax Logging clear Command Mode Syntax Show logging Command ModeLogging clear Show loggingSystem Clock Commands Syntax Show event-log Command ModeSystem Clock Commands Show event-logSntp-server enable Syntax No sntp-server enableSntp-server ip Syntax Sntp-server ip 1 2 ipSntp-server date-time Sntp-server ip 6-38 show sntpSyntax No sntp-server daylight-saving Default Setting Sntp-server daylight-savingSntp-server timezone Syntax Sntp-server timezone hoursShow sntp TAIPEI, BeijingDhcp Relay Commands Dhcp-relay enableSyntax No dhcp-relay enable Default Setting Dhcp Relay CommandsSyntax Dhcp-relay primary secondary ipaddress Dhcp-relayShow dhcp-relay Snmp Commands Snmp CommandsDisplays the Snmp v3 notification filter assignments Snmp-server community Snmp-server contactSnmp-server location Snmp-server enable server Snmp-server hostHostname Name of the host. Range 1-63 characters Snmp-server trapCommand Line Interface Snmp-server engine-id Snmp-server user Syntax Snmp-server user user-nameSnmp-server targets Snmp-server filter Default Setting Snmp-server filter-assignments Show snmp groupsSyntax Show snmp groups Command Mode Syntax Show snmp users Command ModeShow snmp users Show snmp group-assignmentsSyntax Show snmp group-assignments Command Mode Syntax Show snmp target Command ModeShow snmp target Show snmp filterSyntax Show snmp filter-assignments Command Mode Show snmp filter-assignmentsShow snmp Flash/File Commands BootfileSyntax Bootfile filename Flash/File CommandsSyntax Copy ftp tftp file copy config ftp tftp CopyDelete Dir File information is shown belowShow bootfile Radius ClientRadius-server port Radius-server addressSyntax Radius-server secondary port portnumber Radius-server key Syntax Radius-server secondary key keystringRadius-server retransmit Syntax Radius-server secondary retransmit numberofretriesRadius-server timeout Syntax Radius-server secondary timeout numberofsecondsRadius-server port-accounting Syntax Radius-server secondary port-accounting portnumberRadius-server timeout-interim Radius-server radius-mac-formatSyntax Radius-server vlan-format hex ascii Radius-server vlan-formatShow radius 802.1X Authentication 802.1x 802.1X AuthenticationSyntax 802.1x supported required no Using the Command Line Interface 802.1x broadcast-key-refresh-rate Syntax 802.1x broadcast-key-refresh-rate rate802.1x session-key-refresh-rate 802.1x session-timeoutSyntax 802.1x session-key-refresh-rate rate 802.1x-supplicant enable Default802.1x-supplicant user Show authentication MAC Address Authentication Address filter default Syntax Address filter default allowed deniedAddress filter entry Syntax Address filter entry mac-addressallowed deniedAddress filter default 6-79 802.1x-supplicant user Mac-authentication server Syntax Mac-authentication server local remoteAddress filter delete Syntax Address filter delete mac-addressMac-authentication session-timeout Filtering CommandsSyntax Mac-authentication session-timeout minutes Filtering Commands Filter local-bridgeOutdoor 11a Building to Building config#filter local-bridge Syntax No filter ap-manage Default Filter uplink enableSyntax No filter uplink enable Default Filter ap-manageFilter ethernet-type enable Syntax No filter ethernet-type enable DefaultFilter ethernet-type protocol Show filtersWDS Bridge Commands WDS Bridge CommandsBridge mode Syntax Bridge mode master slaveBridge role WDS Syntax Bridge role ap repeater bridge root-bridgeSyntax Bridge channel-auto-sync enable disable Bridge channel-auto-syncBridge-link parent Syntax Bridge-link parent mac-addressBridge-link child Syntax Bridge-link child index mac-addressBridge dynamic-entry age-time Syntax Bridge dynamic-entry age-time secondsSeconds Show bridge aging-time Show bridge filter-entry MAC Syntax Show bridge link ethernet wireless a g index Show bridge linkParent 00-12-34-56-78-9a Child Bridge stp enable Spanning Tree CommandsBridge Commands Syntax No bridge stp enable Default Setting Bridge stp forwarding-delaySyntax Bridge stp hello-time time No bridge stp hello-time Bridge stp hello-timeBridge stp max-age Bridge stp priority Syntax Bridge stp max-age seconds No bridge stp max-ageSyntax Bridge stp prioritypriority no bridge stp priority Bridge-link path-cost Syntax Bridge-link path-cost index costSyntax Bridge-link port-priority index priority Bridge-link port-priorityShow bridge stp Syntax Show bridge stp Command Mode Ethernet Interface CommandsEhternet Interface Commands Interface ethernet Dns serverIp address Ip address ip-address netmask gateway no ip addressSyntax No ip dhcp Default Setting Ip dhcpSyntax No shutdown Default Setting Speed-duplexSyntax Speed-duplex auto 10MH 10MF 100MF 100MH ShutdownSyntax Show interface ethernet Default Setting Show interface ethernetWireless Interface Commands Wireless Interface CommandsInterface wireless Syntax Interface wireless a gSpeed VapSyntax Speed speed Turbo Syntax Turbo static dynamic no turboMulticast-data-rate Syntax Multicast-data-rate speedChannel Syntax Channel channel autoRadio-mode Transmit-powerSyntax Radio-mode b g b+g Preamble Default Setting +g mode Command ModeSyntax Preamble long short-or-long Antenna control Syntax Antenna control diversity left rightAntenna id Syntax Antenna id antenna-idAntenna location Syntax Antenna location indoor outdoorBeacon-interval Syntax Beacon-interval intervalDtim-period Syntax Dtim-period intervalFragmentation-length Syntax Fragmentation-length lengthRts-threshold Syntax Rts-threshold thresholdSyntax No super-a Default Setting Super-aSuper-g Syntax No super-g Default SettingDescription Ssid Syntax No closed-system Default SettingClosed-system Assoc-timeout-interval Syntax Assoc-timeout-interval minutesMax-association Syntax Max-association countAuth-timeout-value Syntax Auth-timeout-value minutesShow interface wireless Syntax Show interface wireless a g vap-id130 131 132 Rogue AP Detection Commands Show stationRogue-ap enable Rogue AP CommandsRogue-ap authenticate Syntax No rogue-ap authenticate Default SettingSyntax Rogue-ap duration milliseconds Rogue-ap durationRogue-ap interval Syntax Rogue-ap interval minutes Rogue-ap scan138 Wireless Security Commands Wireless Security CommandsShow rogue-ap Auth 141 Syntax No encryption Default Setting EncryptionKey Key index size type value no key indexSyntax Transmit-key index Transmit-keyKey 6-143 encryption 6-142 transmit-key Cipher-suite Syntax Cipher-suite aes-ccmp tkip wepMicmode Syntax Micmode hardware softwareWpa-pre-shared-key Syntax Wpa-pre-shared-key hex passphrase-keyvaluePmksa-lifetime Syntax Pmksa-lifetime minutesPre-authentication Link Integrity Commands Syntax No link-integrity ping-detect Default SettingLink Integrity Commands Link-integrity ping-detectLink-integrity ping-interval Link-integrity ping-hostSyntax Link-integrity ping-interval interval Syntax Link-integrity ping-fail-retry counts Link-integrity ping-fail-retryLink-integrity ethernet-detect Syntax No link-integrity ethernet-detect Default Setting Iapp CommandsShow link-integrity Syntax No iapp Default Vlan CommandsIapp Vlan Commands Syntax No vlan enable Default Command DescriptionVlan Management-vlanidVlan-id Syntax Vlan-id vlan-idWMM Commands WMM CommandsWmm Syntax No wmm supported requiredWmm-acknowledge-policy Syntax Wmm-acknowledge-policy acnumber ack noackAP Access Point BSS Wireless client Wmmparam161 162 Troubleshooting Page Page Page Cables and Pinouts TWISTED-PAIR Cable Assignments10/100BASE-TX PIN Assignments STRAIGHT-THROUGH Wiring Crossover Wiring PIN DIN Connector Pinout Pin DIN Ethernet Port PinoutPIN DIN to RJ-45 Cable Wiring Glossary CSMA/CA Infrastructure Radius Virtual LAN Vlan Glossary-6 Index RTS STA

Related manuals

Manual 20 pages 14.36 Kb