Radio Shack PRO-2053 owner manual Using the Attenuator, Turning the KEY Tone on and OFF

Page 29
#CF98Cý ã00ô

To change the receive mode, repeatedly press MODE. The receive mode changes as follows:

ã) — accesses the AM mode

") — accesses the FM mode

)+ — accesses the FM Mode, Motorola Trunking System (with a 4- or 5-digit ID code)

!— accesses the FM Mode, EDACS Trunking System (with 4-digit decimal ID code or 5-digit AFS code)

Note: MO (MOT) and ED modes are not available when the scanner tunes up or down through the frequency ranges in which the trunking operation is not used.

USING THE ATTENUATOR

To reduce interference or noise caused by strong signals, you can reduce the scanner's sensitivity to these signals.

There are two attenuator modes in your scanner. In normal attenuator mode, you set the attenuator in each channel or each band/ group in the search and tune mode. In global mode, you set the attenuator only once. The global setting affects every mode.

Press ATT to turn on or off the attenuator while the channel number is indicated, or while the scanner is searching through bands/groups. When the attenuator is on, ã appears at the seventh digit in the top line.

When you turn it off, ã changes to "ô". You cannot set the attenuator while the scanner is scanning.

Press FUNC then ATT to set the attenuator to

the global mode.appears for 2 seconds at the bottom line and (on) or # (off) appears. Press ATT to turn on or off the attenuator. ã00FE or ã00Vý appears on the bottom line while scanning.

Press FUNC then ATT again to turn off the global attenuation mode. *FID8Cýã00 is indi- cated at the bottom line for 2 seconds.

Note: If you turn on the attenuator, the scan- ner might not receive weak signals.

TURNING THE KEY TONE ON AND OFF

Each time you press any of the scanner's keys, the scanner sounds a tone. To turn the scanner's key tone off or on:

1.If the scanner is on, turn VOLUME OFF/ MAX counterclockwise until it clicks to turn the scanner off.

2.Turn VOLUME OFF/MAX clockwise to

turn the scanner on. 3<C:FD<ý 0Fý L8C

0ILEB@E> appears.

3.While 3<C:FD<ý 0Fý L8Cý 0ILEB@E>

appears, press 1 to turn on the key tone or 2 to turn it off.

CHANGING THE DISPLAY CONTRAST

1.Press MAN.

2.Press FUNC then 9. 1J<ý1Gó FNEýB<PJ

KFýJ<Ký:FEKI8JKô appears.

3.Press 8 or 9 to select the contrast.

4.Press ENTER to set the display contrast.

CLONING PROGRAMMED DATA

You can transfer programmed data to and from another RadioShack PRO-2053 or a PRO-93 scanner using an optional connect- ing cable with 1/8-inch phone plugs on both ends, (not included) available at your local RadioShack store.

Follow these steps to clone the data.

Special Features

29

Image 29
Contents PRO-2053 Channel Desktop Trunk-Tracking Scanner FCC Wants You to Know Contents General Guide to Frequencies Special FeaturesTrunking Operation Specifications TroubleshootingTriple Conversion Superheterodyne Re Simultaneous Trunking OperationCharacter, 4-Line, Alphanumeric Dis Telescoping Antenna provides excellent Scanning LegallyUsing AC Power Power SourcesUsing Vehicle Battery Power PreparationConnecting AN EARPHONE/ Headphones Connecting the AntennaConnecting an Outdoor Antenna Listening SafelyLook AT the Keypad Traffic SafetyAbout Your Scanner Quick Start Understanding Your Scanners Modes Understanding BanksEdacs Mode Open and Closed Modes Turning on the Scanner and Setting SquelchOperation Storing Known Frequencies Into Channels Assigning a Text Tag to a Channel Storing Trunking Frequencies Into ChannelsStoring Text Tags Assigning a Text Tag to a Bank Text Input ChartAssigning a Text Tag to a Group Bank Band Finding and Storing Active FrequenciesSearching a Preprogrammed Fre- quency Range Search bank SR0 Marine band Receive mode FM Search bank SR1 CB band Receive mode AM Group Search bank SR2 Police/Fire band Receive Mode FMSearch bank SR4 Ham band Receive mode FM Search bank SR3 Aircraft Receive mode AMSpecial Notes Manually Tuning a FrequencyListening to the Weather Band Listening to a Weather Channel Using Frequency Copy FunctionDisplaying Weather Messages WX Alert and Beep Tone Confir- mationTurning Channel-Storage Banks Off and On Scanning the ChannelsCopying a Frequency into the Pri- ority Channel Locking OUT Channels or Frequencies Special FeaturesUsing the Delay Function Reviewing Locked-Out Frequen- cies PriorityClearing a Locked-Out Frequency Clearing All Locked-Out Frequen- cies in a Search BankChanging the Receive Mode Turning the KEY Tone on and OFF Using the AttenuatorChanging the Display Contrast Cloning Programmed DataTrunking Operation Programming Trunking Frequencies Setting Squelch for the Trunking ModeUnderstanding Trunking DF appears Programming Motorola Trunking Systems UHF-LoProgramming Fleet Maps Programming Motorola Trunking System 800 MHzSize Code Storing Talk Group IDs Talk Group IDs8Wdaý&# ?ýDe$ý CEJ0ýdedTurning Sub-Banks On or Off Talk Group ID HoldLocking Out Talk Group IDs Delay Function in ID Indication ModeReviewing Locked-Out Talk Group IDs Clearing Talk Group IDsGeneral Guide to Frequencies Changing the Open/Closed ModeOpen and Closed Modes US Weather Frequencies in MHzBirdie Frequencies Ham Radio FrequenciesTypical Band Usage Guide to the Action BandsHF Band VHF BandUHF Band Primary UsageBand Allocation AbbreviationsServicesHigh Frequency HF Meter Amateur Band-50-54 MHz in 5 kHz steps VHF High Band 148-174 MHz in 5, 6.25 or 7.5 kHz steps New Mobile Narrow Band 220-222 MHz in 5 kHz steps Ultra High Frequency UHF Conventional Systems Band Locally Assigned in 6.25 kHz steps Frequency Conversion RESETTING/INITIALIZING the Scanner TroubleshootingResetting the Scanner Initializing the ScannerCare Sensitivity 20 dB S/N SpecificationsSpecifications Page Page Limited One-Year Warranty