Air_US_rev_111.qxd
THE AIR DISPLAY & SETTING UP
| EXIT |
|
|
|
|
|
|
|
|
|
|
|
|
|
| Overload Indication | ||||
|
|
|
|
|
|
|
|
| ||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| UP | |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
| |||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
| ENTER |
|
|
|
|
|
|
|
|
|
|
|
|
|
| DOWN | ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
ENTER key | CURSOR UP/DOWN keys | |||||||||||||||||||
The ENTER key has two main functions: | These keys are used for navigating and adjusting | |||||||||||||||||||
• | To enter the menus currently displayed. | parameter values. | ||||||||||||||||||
• | To set the displayed parameter in Edit mode. | The previous page illustrates how to navigate through | ||||||||||||||||||
When a parameter can be edited via the CURSOR keys a | parameters using the AIR display. | |||||||||||||||||||
“*” is set as the first character in front of the parameter. | Overload Indication LED | |||||||||||||||||||
EXIT key | ||||||||||||||||||||
When this LED flashes the monitors | ||||||||||||||||||||
The EXIT key is used to exit the current display and go to | beyond max performance. A continuos overload will | |||||||||||||||||||
previous menu level. | activate the amp protection circuit and the monitor will be | |||||||||||||||||||
|
|
|
|
|
|
| shut down. The monitor can be reactivated after a short |
period of cooling down.
This situation will NOT damage the monitor in any way.
Setting up - Introduction
To make your setup operate as intended correct cabling is essential. Choose one of the described setups and connect exactly as illustrated. The following section is a
Setups including Subwoofer:
To activate the subwoofer, please choose an appropriate
General Setup Procedure
•Decide which Setup you are going to build.
•Connect monitors exactly according to the illustrations on the following pages.
•Power up all monitors.
•Set one of the
•NOTE: There can be only ONE System Controller in a setup.
After
Set tasks for all monitors via the System Controller unit via the following procedure:
-Enter Setup menu by pressing ENTER, ARROW DOWN, ENTER.
-Select the setup type you are using.
-Press ENTER again and the System will generate Pink Noise in one of the monitors.
-Select appropriate task for the monitor currently fed with Pink Noise using the ARROW keys and press ENTER to confirm.
-Continue allocating tasks for all monitors in the system.
Your monitor system is now set up ready for calibration and
These procedures are described on pages
The setups will ONLY operate correctly if connected according to the illustrations!
9