Advantech PPC-V106 user manual Overview of Hardware Installation and Upgrading

Page 28

Chapter 3 Hardware and Peripheral Installation

3.1 Overview of Hardware Installation and Upgrading

The panel PC consists of a PC-based computer that is housed in a rugge- dized aluminum enclosure. Any maintenance or hardware upgrades can be completed after removing both panels..

Warning! Do not remove the ruggedized aluminum covers until you have verified that no power is flowing within the panel PC. Power must be switched off

and the power cord must be unplugged. Every time you service the panel PC, you should be aware of this.

3.2 Installing the 2.5" Hard Disk Drive (HDD)

You can attach one enhanced Integrated Device Electronics (IDE) hard disk drive to the panel PC's internal controller which uses a PCI local-bus interface. The advanced IDE controller supports faster data transfer and allows the IDE hard drive to exceed 528 MB. The following are instruc- tions for installation:

1.Detach the HDD bracket by unscrewing the four screws (#2) on the top of the HDD bracket.

2

Screw

11930030400-M3x4L

21933030500-M3x5L

PPC-V106 User Manual

16

Image 28

Contents User’s Manual Fanless Vehicle Mounted Terminal with 10.4 TFT LCDCopyright FCC Class B Packing List Additional Information and Assistance Contact informationSafety Instructions Wichtige Sicherheishinweise Viii Contents Chapter VIA Chipset Appendix a Programming the Watchdog Timer Xii General Information General Specifications IntroductionStandard PC functions Audio function LCD Specifications Backlight lifetime 20,000 hoursDimensions System Setup Quick Tour of the Panel PC Front View of the Panel PCRear Side View of the Panel PC Installation Procedures Connecting the Power CordConnecting the Keyboard or Mouse Switching On the PowerRunning the Bios Setup Program Installing System Software Prior to shipment of your panel PCInstalling the Drivers InstallPage Hardware and Peripheral Installation Overview of Hardware Installation and Upgrading Installing the 2.5 Hard Disk Drive HDDPlacing the Rubber Seal Placing the Rubber SealInstalling the Universal Arm Universal ArmJumper Settings and Connectors Setting Jumpers Jumpers and Switches Locating Jumpers and SwitchesConnectors Panel PC connectorsCPU Installation Locating ConnectorsCmos Clear for External RTC JP1 1 COM2 RS-232/422/485 Setting JP5COM-port Interface Serial port default settings 2 COM1/COM2/COM3/ Pin 9 Output Setting JP4 COM1/2/3 Pin 9 Output SettingJP4JP3 Setting LCD Panel Power Setting VGA InterfaceVIA Chipset Installation 4-in-1 Driver for Windows 98/2000/XP Further InformationAGP Svga Setup Chipset Installation of Svga DriverDisplay memory Installation for Windows 98/ME Installation for Windows 2000/XPPage PCI Bus Ethernet Interface Installation of Ethernet Driver Installation for Windows 98/ME Further Information Audio Installation of Audio Driver USB Installation of USB 2.0 Driver Driver Installation for Windows XPDriver Installation for Windows Driver Installation for Windows ME / 98 / 98SE Touchscreen General specifications General informationInstallation of Touchscreen Drivers Environmental SpecificationsInstallation of Resistive T/S driver for Windows 98/ME Installation of Resistive T/S driver for Windows 2000/XP Installation of Infrared T/S driver for Windows 2000/XPPage Programming the Watchdog Timer Appendix a Programming the Watchdog Timer Programming the Watchdog TimerMOV DX,2EH MOV DX,2EH MOV AL,AAH Pin Assignments Internal Speaker Connector CN14 Inverter Power Connector CN10Appendix B Pin Assignments Floppy Drive Connector CN16 Reserved Table B.3 Floppy drive connector CN16IDE Hard Disk Drive Connector CN15 IR Connector CN8 Reserved Lvds Connector CN4Flat Panel Display Connector CN2 Reserved COM1 COM211 COM3 Connector CN 10 COM3COM 4 Connector CN USB PortParallel Port Connector CN11 VGA Connector