Advantech PPC-V106 user manual General information, General specifications

Page 58

Chapter 10 Touchscreen

10.1Introduction

10.1.1General information

There are two kinds of touch screens for the PPC-V106 series, one is resistive touch screens, the other for infrared touch screens.

The resistive touch screen incorporates advanced second-generation resistive, impact-resistant technology, which allows 75% light transmis- sion. There is also an antiglare surface for greatly enhanced visual resolu- tion. It also has new and improved scratch-resistant features.

The resistive touch screen is manufactured from UL-recognized compo- nents. When properly installed, the touchscreen's ball impact resistance meets the UL 1950 standard. Its fire resistance meets the UL-746C, 19

mm(0.75") flame test standard. Systems incorporating the touchscreen, controllers, and cables have been approved to FCC Class A and Class B standards.

For more detailed information, please visit the following websites:

www.dynapro.com

www.3m.com/us/electronics_mfg/touch_systems

www.elotouch.com

Advantech Co.,Ltd. reserves the right to alter the touchscreen at any time without notice.

10.1.2 General specifications

Please refer to Chapter 1, Section 1.2 of this manual.

PPC-V106 User Manual

46

Image 58

Contents User’s Manual Fanless Vehicle Mounted Terminal with 10.4 TFT LCDCopyright FCC Class B Packing List Additional Information and Assistance Contact informationSafety Instructions Wichtige Sicherheishinweise Viii Contents Chapter VIA Chipset Appendix a Programming the Watchdog Timer Xii General Information General Specifications IntroductionStandard PC functions Audio function LCD Specifications Backlight lifetime 20,000 hoursDimensions System Setup Quick Tour of the Panel PC Front View of the Panel PCRear Side View of the Panel PC Connecting the Keyboard or Mouse Installation ProceduresConnecting the Power Cord Switching On the PowerRunning the Bios Setup Program Installing System Software Prior to shipment of your panel PCInstalling the Drivers InstallPage Hardware and Peripheral Installation Overview of Hardware Installation and Upgrading Installing the 2.5 Hard Disk Drive HDDPlacing the Rubber Seal Placing the Rubber SealInstalling the Universal Arm Universal ArmJumper Settings and Connectors Setting Jumpers Jumpers and Switches Locating Jumpers and SwitchesConnectors Panel PC connectorsCPU Installation Locating ConnectorsCmos Clear for External RTC JP1 1 COM2 RS-232/422/485 Setting JP5COM-port Interface Serial port default settings 2 COM1/COM2/COM3/ Pin 9 Output Setting JP4 COM1/2/3 Pin 9 Output SettingJP4JP3 Setting LCD Panel Power Setting VGA InterfaceVIA Chipset Installation 4-in-1 Driver for Windows 98/2000/XP Further InformationAGP Svga Setup Chipset Installation of Svga DriverDisplay memory Installation for Windows 98/ME Installation for Windows 2000/XPPage PCI Bus Ethernet Interface Installation of Ethernet Driver Installation for Windows 98/ME Further Information Audio Installation of Audio Driver USB Installation of USB 2.0 Driver Driver Installation for Windows XPDriver Installation for Windows Driver Installation for Windows ME / 98 / 98SE Touchscreen General specifications General informationInstallation of Touchscreen Drivers Environmental SpecificationsInstallation of Resistive T/S driver for Windows 98/ME Installation of Resistive T/S driver for Windows 2000/XP Installation of Infrared T/S driver for Windows 2000/XPPage Programming the Watchdog Timer Appendix a Programming the Watchdog Timer Programming the Watchdog TimerMOV DX,2EH MOV DX,2EH MOV AL,AAH Pin Assignments Internal Speaker Connector CN14 Inverter Power Connector CN10Appendix B Pin Assignments Floppy Drive Connector CN16 Reserved Table B.3 Floppy drive connector CN16IDE Hard Disk Drive Connector CN15 IR Connector CN8 Reserved Lvds Connector CN4Flat Panel Display Connector CN2 Reserved COM1 COM211 COM3 Connector CN 10 COM3COM 4 Connector CN USB PortParallel Port Connector CN11 VGA Connector