Metrologic Instruments MS6130 MX003 Appendix B, Default Settings of the MS6130 and MX Receiver

Page 36

APPENDIX B

Default Settings of the MS6130 and “MX” Receiver

Before the MS6130 hand-held scanner and “MX” Receiver ships from the factory, the factory programs the scanners to a group of default settings. An asterisk ( * ) in the charts on the following pages marks the default settings of the units. If an asterisk is not in the default column then the default setting is Off or Disabled.

The MS6130 and “MX” receiver do not support every parameter. For those parameters that are a transmitter function, a letter “T” will appear in the second column of the charts, for the “MX”, the

letter “R”.

RS-232, light pen and keyboard wedge emulation does not support every parameter. If your host device’s communication supports a parameter listed in the charts on the following pages, a check mark will appear.

In order for the “MX” receiver to communicate with your RS-232, light pen or keyboard wedge host device properly, program it to meet your individual scanning needs. Since each host system is unique, change the default settings to match your host system requirements. To modify default settings, refer to the MS4120 and MS951 Programming Guides.

Note: If your “MX” Interface is connected to a MS700i/MS720i scanner, use the bar codes in the ScanSelect Programming Guide to match your scanner’s settings to the host system requirements.

T - Transmitter (MS6130 Hand-held)

R - Receiver (“MX”)

Parameter

T - Transmitter

Default

RS-232

Light

R - Receiver

Pen

 

 

 

 

 

 

 

 

Enter/Exit Program Mode

T

 

 

 

Recall Defaults

R

 

 

 

Enter Program Mode After Any

 

 

 

 

Scan

T

*

3

3

Enter Program Mode Only on

 

 

 

 

First Scan

T

 

3

3

Short Range Activation Out of the

 

 

 

 

Stand

T

 

3

3

Long Range Activation Out of the

 

 

 

 

Stand

T

*

3

3

Short Range Activation in the

 

 

 

 

Stand

T

 

3

3

 

 

 

 

 

32

Page 35 Page 37
Image 36
Page 35 Page 37
Contents Metrologic INSTRUMENTS, INC Table of Contents Table of Contents Printer Note Leave page blank MS6130 Hand Held BAR Code Scanner MX003 Series Scanner Interfaces Unpacking List Transmitter GroupReceiver Group Connections of the Mxnterfacei to the Host Device Except versionConnections of the Keyboard Wedge Mxnterfacei to the PC Version 17 onlyConnections of the MS700I/MS720I With Mxto the Host Device Configuration of the MS700I/MS720I with MX Page Configuration of the Mxto the Scanpal Data Collector Page Keyboard Wedge KB Interface KB Parameter Keyboard TypeKB Parameter Keyboard Type KB Parameter Caps Lock Mode KB Parameter Alt Mode Microsecond DelayMillisecond Delay Millisecond Delay KB Parameter XT Clean-Up BitConfiguration of the MS6130 HAND-HELD Enabling the MS700I/MS720I SCANNER’S RF LOW Speed Option Changing the ID Handset /XMatching Procedure Parts of the MS6130 HAND-HELD BAR Code Scanner Output WindowComponents of the MS6130 Series Stand Installation of the MS6130 Series Stand Installation of the 6000 Series Universal Charging Stand Permanent Counter TOP InstallationNicd Battery Charger with Reconditioning Feature Recommended USEVisual Indicators Audible Indicators One BeepRazzberry Tone Two BeepsAudible Indicators Maintenance LabelsTroubleshooting Specifications Appendix aMX003 Series Scanner Interface Specifications Temperature Characteristics Degrees Celsius of each Cell Default Settings of the MS6130 and MX Receiver Appendix BRTS/CTS UPC EAN Parameter Transmitter Default Keyboard Receiver Wedge Appendix C MX003 Series Scanner Interface Pin AssignmentsPin Function Appendix E Appendix F PatentsIndex ESDTroubleshooting
Top Page Image Contents